GT36UHDGT56UHD Installation Instructions
Page 1
... products on the transducer. Acetone damages the plastic transducer housing. Read all installation instructions before proceeding with outboard or inboard/outboard motors, the transducer should extend 3.5 mm (0.125 in.) below a fiberglass hull or 10 mm (0.375 in .) from ignition wires, house batteries and wires, trolling motor batteries and wires, and high-energy wires such as possible but at support.garmin.com. To obtain...
... products on the transducer. Acetone damages the plastic transducer housing. Read all installation instructions before proceeding with outboard or inboard/outboard motors, the transducer should extend 3.5 mm (0.125 in.) below a fiberglass hull or 10 mm (0.375 in .) from ignition wires, house batteries and wires, trolling motor batteries and wires, and high-energy wires such as possible but at support.garmin.com. To obtain...
GT36UHDGT56UHD Installation Instructions
Page 2
... the transducer to the bracket with screws, it is recommended to use a 25 mm (1 in.) drill bit to drill a pass-through hole completely through pilot hole. 13Mark the pilot-hole location for optimal performance. • On single-drive boats, the transducer must not be mounted in the path of electrical interference. The cables connected to electrical wires...
... the transducer to the bracket with screws, it is recommended to use a 25 mm (1 in.) drill bit to drill a pass-through hole completely through pilot hole. 13Mark the pilot-hole location for optimal performance. • On single-drive boats, the transducer must not be mounted in the path of electrical interference. The cables connected to electrical wires...
GT36UHDGT56UHD Installation Instructions
Page 3
...cable close to electrical wires or other sources of electrical interference. • You must be on the top side of the trolling motor housing when the motor is stowed. You cannot get a depth or distance reading when out of the water. Testing the Transom-Mount Transducer Installation NOTICE When adjusting the depth of the transducer, make moderate turns...clamps through hole with marine sealant so it too tightly. Because water is necessary to carry the sonar signal, the transducer must avoid routing the cable where it is parallel to the bottom when in use a cable exit that were added...
...cable close to electrical wires or other sources of electrical interference. • You must be on the top side of the trolling motor housing when the motor is stowed. You cannot get a depth or distance reading when out of the water. Testing the Transom-Mount Transducer Installation NOTICE When adjusting the depth of the transducer, make moderate turns...clamps through hole with marine sealant so it too tightly. Because water is necessary to carry the sonar signal, the transducer must avoid routing the cable where it is parallel to the bottom when in use a cable exit that were added...
GT36UHDGT56UHD Installation Instructions
Page 4
....) total Garmin SideVü at 1 MHz, max. depth of cable pins Water rating 12 IPX71 GT36UHD models Transmit power (RMS) Traditional: Not applicable Garmin ClearVü™: 500 W Garmin SideVü: 500 W Frequency Traditional: Not applicable Garmin ClearVü and Garmin SideVü: CHIRP 455 kHz (420-490 kHz); UHD CHIRP 800 kHz (770-840 kHz); Appendix Specifications All models Dimensions...
....) total Garmin SideVü at 1 MHz, max. depth of cable pins Water rating 12 IPX71 GT36UHD models Transmit power (RMS) Traditional: Not applicable Garmin ClearVü™: 500 W Garmin SideVü: 500 W Frequency Traditional: Not applicable Garmin ClearVü and Garmin SideVü: CHIRP 455 kHz (420-490 kHz); UHD CHIRP 800 kHz (770-840 kHz); Appendix Specifications All models Dimensions...