Garmin Reactor 40 Hydraulic Autopilot Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Reactor 40 Hydraulic Autopilot manuals!
Problems with Garmin Reactor 40 Hydraulic Autopilot?
Ask a Question
Free Garmin Reactor 40 Hydraulic Autopilot manuals!
Problems with Garmin Reactor 40 Hydraulic Autopilot?
Ask a Question
Popular Garmin Reactor 40 Hydraulic Autopilot Manual Pages
Configuration Guide PDF - Page 1
... sequence, select an option: • On a helm control, select Menu > Setup > Dealer
Autopilot Setup > Wizards > Dockside Wizard. • On a chartplotter, select Settings > My Vessel >
Autopilot Installation Setup > Wizards > Dockside Wizard. 3 Select the vessel type. 4 If prompted, follow the on-screen instructions to set the helm lock-to-lock, 5 If prompted, follow the on calm and hazard-free...
Configuration Guide PDF - Page 2
...Sea
Trial Wizard on the boat must be a problem with a clear view of the sky to provide...part of the Sea
Trial Wizard, select Begin. • If you are performing this procedure outside of the Sea Trial Wizard on -screen instructions... Settings > My Vessel > Autopilot Installation Setup > Compass Setup > Compass Cal. > Begin.
2 Follow the directions until calibration is shown.
NOTE: Garmin...
Configuration Guide PDF - Page 3
... same direction as the current. 2 Select an option:
• If you are performing this procedure outside of the Sea Trial Wizard on a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Compass Setup > Set North > Begin.
3 Continue to an optional GPS device, and the device has acquired a GPS position. When the Autotune procedure is complete, you turn...
Configuration Guide PDF - Page 4
... seconds. Manually Defining Individual Configuration Settings Configuring certain configuration settings may be available after a 2018 software update. Descriptions of Sensor Information 1 Select an option:
• On a helm control, from the heading screen, select Menu > Setup > System > System Information.
2 Hold the center key for Dealer Autopilot Setup is available on -screen instructions...
Configuration Guide PDF - Page 5
... steering wheel from the heading screen, select Menu >
Setup > Dealer Autopilot Setup > Steering System Setup > Rudder Sensor Setup. • On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Steering System Setup > Rudder Sensor Setup. If the value does not match the value on the helm, near the hydraulic connectors. Low Speed Counter: Allows you can bypass this...
Configuration Guide PDF - Page 6
...the USA and other countries. These trademarks may not be used without the express permission of Garmin Ltd. or its subsidiaries.
NMEA®, NMEA 2000®, and the NMEA 2000 logo ...of the National Marine Electronics Association. Reactor™ and Shadow Drive™ are trademarks of Garmin. Max. Starboard Angle or Max. Stbd. Ang.: Allows you to enter the angle at which your rudder...
Installation Instructions PDF - Page 1
...; 40 HYDRAULIC Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for product warnings and other and to avoid magnetic interference with the CCU. CCU Mounting and Connection Considerations • The CCU is approximately the same distance from moving parts. You are available from www.garmin.com...
Installation Instructions PDF - Page 2
... detects when you are building a NMEA 2000 network.
You should install this cable only if you manually take control of the helm and suspends autopilot control of the boat. • The Shadow Drive must be mounted horizontally and as level
as a compatible Garmin chartplotter to the pump. • The Shadow Drive must be
extended...
Installation Instructions PDF - Page 3
.... If there is not included in all autopilot packages.
If needed , specific connection diagrams are included in the detailed installation instructions for each component. Hydraulic connections are not shown in this diagram. Hydraulic connections are not shown in this diagram. You must install the Shadow Drive valve properly in the hydraulic steering line, and connect it near the...
Installation Instructions PDF - Page 4
... power cable to configure and control the autopilot system.
After you must select a location and determine the correct mounting hardware (ECU Mounting and Connection Considerations, page 2). 1 Hold the ECU in the product specifications.
Mounting the CCU 1 Determine the mounting location. 2 Using the CCU as a compatible Garmin chartplotter to the boat battery. Test any...
Installation Instructions PDF - Page 5
...Autopilot System, page 5).
Follow the installation instructions...Installing the Pump The pump (sold by Garmin, it will drain your device at which to connect the Shadow Drive to the hydraulic steering of your boat, all the parts needed to build one power source should be connected to the same NMEA 2000 network as a compatible Garmin chartplotter to configure and control the autopilot...
Installation Instructions PDF - Page 6
... cable to the CCU and to the instructions provided by following the instructions provided with the device. You can observe air bubbles during the bleeding process.
2 Insert a bypass hose between the cylinder bleed ports. Before you bleed the hydraulic system, you install the autopilot without a dedicated helm control, the autopilot CCU must be applied to the...
Installation Instructions PDF - Page 7
... on configuring the autopilot. Function N/A
Ê
N/A
Ë
Blue -
See the included configuration guide for a list ...manual for extended runs of different situations you plan to the input port on the connected Garmin device. Tx/A (+)
Ì
White -
Tx/A (+)
Ì
White - Wizard on the included NMEA 0183 data cable. See the installation instructions provided with the autopilot...
Installation Instructions PDF - Page 8
... incidental exposure to water of up to 1 m for up to www.garmin.com/waterrating. For more information, go to 30 min. Rx/B (-) ...update 129283 Cross track error 129284 Navigation data 129540 GNSS satellites in . (23 × 25 mm) 2.4 oz. (68 g) From 5°F to 140°F (from the helm control must be connected to
Ë
NMEA 0183 ground) Blue -
Function
Brown - Alarm
Specification...
Installation Instructions PDF - Page 9
... and the ECU has beeps, and
Between ECU and timed out.
Route To maneuver.
Autopilot placed data while performing a
in to support.garmin.com for
risen above 100°C
5 seconds
(212°F ).
• The ECU shuts
down
Error Message
Cause
Autopilot Action
Error: ECU Voltage The ECU voltage has has Dropped Rapidly dropped quickly below
7.0 Vdc...
Garmin Reactor 40 Hydraulic Autopilot Reviews
We have not received any reviews for Garmin yet.