Installation Instructions
Page 1
...must be performed by properly venting the dryer to the outdoors. • This dryer must comply with the customer). Step 6 Level Your Dryer (see section 11. 234D1113P002 31-16225-1 07/08/10 GE Step 10 Check the Operation of the dryer control system. Step 11 Place the ...these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the state. These conditions will minimize incomplete combustion. Installation Gas Dryer DESIGN Instructions 06 CER TI FI ED Questions on page 6 of this appliance in any location where it must be UL listed and...
...must be performed by properly venting the dryer to the outdoors. • This dryer must comply with the customer). Step 6 Level Your Dryer (see section 11. 234D1113P002 31-16225-1 07/08/10 GE Step 10 Check the Operation of the dryer control system. Step 11 Place the ...these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the state. These conditions will minimize incomplete combustion. Installation Gas Dryer DESIGN Instructions 06 CER TI FI ED Questions on page 6 of this appliance in any location where it must be UL listed and...
Installation Instructions
Page 2
... TO THE OFF POSITION. The use with natural gas. GAS SUPPLY • A 1/8-in.National Pipe Taper thread plugged tapping, accessible for air opening are: 0 in their absence, the NATIONAL FUEL GAS CODE, ANSI Z223. • This gas dryer is to floor. Always use with UL listed ...transition duct . REMOVING LINT FROM WALL EXHAUST OPENING 2 GAS REQUIREMENTS WARNING • Installation must conform to local codes and ordinances,...
... TO THE OFF POSITION. The use with natural gas. GAS SUPPLY • A 1/8-in.National Pipe Taper thread plugged tapping, accessible for air opening are: 0 in their absence, the NATIONAL FUEL GAS CODE, ANSI Z223. • This gas dryer is to floor. Always use with UL listed ...transition duct . REMOVING LINT FROM WALL EXHAUST OPENING 2 GAS REQUIREMENTS WARNING • Installation must conform to local codes and ordinances,...
Installation Instructions
Page 5
...fasteners that extend into a common duct with the instructions found in "Connecting The Dryer To House Vent" on page 6 of this manual. •Do not terminate exhaust in a chimney, a wall, a ceiling, gas vent, crawl space, attic, under an enclosed floor, or in any other...THE INSTRUCTIONS IN SECTION 9 TO EXHAUST DIRECTLY FROM THE SIDES OR BOTTOM OF THE CABINET. Installation Instructions 7 EXHAUST CONNECTION WARNING - THIS DRYER COMES READY FOR REAR EXHAUSTING. STANDARD REAR EXHAUST (Vented above floor level) ELBOW HIGHLY RECOMMENDED RECOMMENDED CONFIGUR A TION TO MINIMIZE EXHAUST ...
...fasteners that extend into a common duct with the instructions found in "Connecting The Dryer To House Vent" on page 6 of this manual. •Do not terminate exhaust in a chimney, a wall, a ceiling, gas vent, crawl space, attic, under an enclosed floor, or in any other...THE INSTRUCTIONS IN SECTION 9 TO EXHAUST DIRECTLY FROM THE SIDES OR BOTTOM OF THE CABINET. Installation Instructions 7 EXHAUST CONNECTION WARNING - THIS DRYER COMES READY FOR REAR EXHAUSTING. STANDARD REAR EXHAUST (Vented above floor level) ELBOW HIGHLY RECOMMENDED RECOMMENDED CONFIGUR A TION TO MINIMIZE EXHAUST ...
Installation Instructions
Page 6
... refastening devices which extend into the dryer room. 6 See the EXHAUST INFORMATION section. • Minimum clearance between dryer cabinet and adjacent walls or other surfaces is recommended. of 60 sq. Allow 2" of duct to prevent gas pocketing in case of a gas leak in the supply line. •... sit close to overhead cabinets, ceiling, etc. Secure the duct with the NATIONAL FUEL GAS CODE, ANSI Z223. Installation Instructions CONNECTING THE DRYER DON'T TO HOUSE VENT RIGID METAL TRANSITION DUCT • For best drying performance, a rigid metal transition duct is : 0 in...
... refastening devices which extend into the dryer room. 6 See the EXHAUST INFORMATION section. • Minimum clearance between dryer cabinet and adjacent walls or other surfaces is recommended. of 60 sq. Allow 2" of duct to prevent gas pocketing in case of a gas leak in the supply line. •... sit close to overhead cabinets, ceiling, etc. Secure the duct with the NATIONAL FUEL GAS CODE, ANSI Z223. Installation Instructions CONNECTING THE DRYER DON'T TO HOUSE VENT RIGID METAL TRANSITION DUCT • For best drying performance, a rigid metal transition duct is : 0 in...