Hayward EcoStar® SVRS Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward EcoStar® SVRS manuals!
Problems with Hayward EcoStar® SVRS?
Ask a Question
Free Hayward EcoStar® SVRS manuals!
Problems with Hayward EcoStar® SVRS?
Ask a Question
Popular Hayward EcoStar® SVRS Manual Pages
EcoStar® Manual - Page 17
Hayward EcoStar Pump SP3400VSP
Thursday
1:27p
1725rpm 380 Watts
Timer 1 timer will end at 11:45p
EcoStar® Manual - Page 18
Configuration Menu Locked
Configuration Menu press > to next item Time: Th 1:27PM
+ change or > skip
Set Day and Time Thursday 1:27p
Speed Selection rpm
MAX allowed speed 3450 (600-3450rpm)
MIN allowed speed 600 (600-3450rpm)
Set max-speed Prime Period: Auto Sense
Remote Control Mode Standalone/Hayward
Set COMM Bus Address Pool Filter to adjust, > go to enter
Use + / -
Technical Guide - Page 1
Variable Speed Pump and Drive Technical Guide
© 2011 Hayward Pool Products
Version 2 Drive FW 1.02 Interface FW 2.55 residential Interface FW 1.00 commercial
Technical Guide - Page 4
... least 5 times pipe size. Existing Pools: When installing the EcoStar on a new pool, care should be taken to insure the maximum flow does not exceed the capacity of pipe (L) between pump suction port and first elbow or fitting should be taken to ensure proper pipe and equipment sizing to equipment manuals for flow rates.
3" 184gpm 8fps...
Technical Guide - Page 17
... a specific setup menu. Programming - Default settings: Speed 1 1000 RPM 29% Speed 2 1750 RPM 51% Speed 3 2500 RPM 72% Speed 4 3250 RPM 94%
Display Screen
Fig 30
MENU/NAVIGATION BUTTONS
The button will illuminate indicating the
pump has stopped. STOP /RESUME
When pressed it will blink when in
unprotected mode if included with the SVRS
models. It...
Technical Guide - Page 22
...the controller. See page 3 for the max allowed flow for setting speed (fig 41).
SVRS model will now see the MAX allowed speed. Press the button to ...Press the button to a Hayward/Goldline compatible software controls place the MIN and MAX settings at the lowest and highest settings respectively so as #10 above for pipe. Programming-Configuration
9. You can set this from 600-3450 ...
Technical Guide - Page 24
... 45 Page 22 Press the button to continue.
14. For EcoStar interface software v2.51 data linked to a Goldline/Hayward compatible software control pressing & buttons will allow for the control of up to 8 EcoStars assignable to be set, as all settings will only recognize address 1 (Pool Filter) and address 2 (Aux 1/ Spa Filter). ProLogic control software v4...
Technical Guide - Page 32
... the current time.
2. When the Low Temp Operation is activated you are set, the pump will be displayed on the display while the pump is pressed.
3. Operation
1. If the EcoStar you will not start unless one or more timers are using is an SVRS model and there is not achieved within 15 minutes.
4. If this does...
Technical Guide - Page 33
PRESET SPEEDS
Any time one of the pump to the maximum set in the Speed Setup Menu. Operation
Display Screen
Fig 62 STOP RESUME
When pressed it will go to 12 hrs maximum. It will resume normal operations. Disables SVRS if included with the SVRS
models.
QUICK CLEAN
Elevates the speed of the speed buttons is
pressed...
Technical Guide - Page 44
...replace drive. There should be between 0.5 and 1.0 ohms max.
Indicates internal drive voltage is drawing excessive current. Check impeller, diffuser and shaft seals for blockage. Troubleshooting/Fault Codes
This guide will cover only those problems with priming problems are addressed in the owners manual... drive (page 36). All other pump problems including seals, gaskets, impellers, etc...
Technical Guide - Page 45
... verify that it is correct and error still occurs, replace drive. Check incoming supply voltage, if greater than 264 VAC, refer to Hayward Service Bulletin "Pump Error: Ac Volts too High" and follow instructions for blockage.
PFC Circuit Low Drive Error AC Voltage Too Low
Drive Error AC Voltage Too High
Drive Error Heatsink Overheated
Indications
Indicates internal drive voltage...
Technical Guide - Page 46
.... If error still exists remove all (0) check connection between terminal 1 with EcoStar and terminal 4 with Hayward/Goldline Control (page 10). If error still exists...replace drive. There should be sure motor shaft turns freely. Troubleshooting/Fault Codes
Code/Fault
Drive Error Drive failed to start the motor.
Check continuity from the drive and check each motor lead to a Hayward...
Technical Guide - Page 48
... and re-connect. Contact Clemmons Tech Service for isolator. Troubleshooting/Fault Codes
Code/Fault
Indications
Warning NO Comm
Inspect the data wire between the control and EcoStar. If the error has not been eliminated, check the Diagnostic Menu.
ground between the interface and drive. If still tripping breaker, replace drive. Install RS485 isolator, or new interface v2...
Technical Guide - Page 49
... to variable speed . bus connection and NOT the input connections for Standalone/Hayward. . The %/rpm reading does not match between GL/Hayward control and EcoStar. The pump comes on the EcoStar is configured for relay control (page 10) .
Troubleshooting/Fault Codes
Code/Fault
Indications
EcoStar is connected and operating via GL/Hayward control. Control reads "Pool bridge comm."
Technical Guide - Page 50
... is wired and set to the pump, the
EcoStar interface reads "Remote Stop Engaged". wires from freezing temperatures. (page 23)
My EcoStar is sent to operate via the GL/Hayward control. The Speed
buttons and Quick Clean buttons on and off. Try changing channel on the drive (page
10). If problem persists, purchase (2) model XPF 20A 3-wire...
Hayward EcoStar® SVRS Reviews
We have not received any reviews for Hayward yet.