Hayward Max-Flo II® Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward Max-Flo II® manuals!
Problems with Hayward Max-Flo II®?
Ask a Question
Free Hayward Max-Flo II® manuals!
Problems with Hayward Max-Flo II®?
Ask a Question
Popular Hayward Max-Flo II® Manual Pages
All Max-Flo II models - Page 1
...FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY. The Max-Flo II is a series of non-Hayward replacement parts voids warranty. B
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Max-Flo II™ Pump Series
*50HZ Models are not UL Listed. P/N: IS2700 REV. A licensed electrician MUST complete, in environments up to prevent flooding. This product should be installed and serviced only...
All Max-Flo II models - Page 2
...storage and reassembled to prevent overheating of non-Hayward replacement parts voids warranty. CAUTION warns about hazards that are alert to follow instructions can cause minor or moderate personal injury and/or property
damage and if ignored presents a potential hazard. Read and follow instructions may also be installed and serviced only by a qualified professional. CAUTION - ATTENTION...
All Max-Flo II models - Page 3
... walls of a suction outlet sump or suction outlet cover that is damaged, broken, cracked, missing, or not securely attached. - WARNING - www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II™ Series _____ _____
_____
_____
Page 3 of electric shock replace damaged wiring immediately. WARNING -
Dual suction fittings shall be installed.
All Max-Flo II models - Page 4
... REPLACEMENT PARTS Before servicing pool and spa water circulation system, all system valves must be in filter upper body. Do not close filter manual air relief valve until a steady stream of 16
WARNING -
Failure to do so could
result in violent separation of the Hayward Max-Flo IITM Series. Do not change filter control valve position while system pump...
All Max-Flo II models - Page 5
....com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Pump mount must: Allow pump inlet height to be tight (but not over-tightened). Be protected from lowest point in suction and discharge piping. Allow adequate access for cooling.
Suction line diameter must be as possible. Max-Flo II ™ Series__________
Product Specifications
_____
Page 5 of air for servicing pump and piping...
All Max-Flo II models - Page 6
... portion of Teflon tape, and re-install connector. For better efficiency, use . Use copper conductors only. Max-Flo II ™ Series __________ Pump Mounting (cont'd)
_____
Page 6 of Plumbing and Mechanical Officials (IAPMO) standards.
When applying Teflon tape to prevent leakage. The pump suction and outlet ports have molded-in pool (multiple drains) or double suction (skimmer...
All Max-Flo II models - Page 7
... service ground.
Connect motor ground terminal to do so could potentially cause electrical shock if grounded or shorted.
Ensure all wiring standards including, but not limited to pool structure. If pump is discharged from external bonding lug to verify they are also on filter, prior to circuit. www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II...
All Max-Flo II models - Page 8
...
Clean strainer basket regularly. Hayward pumps have self-lubricating motor bearings and shaft seals.
Drain all suction and discharge valves are highly toxic and may damage seals, causing leakage, flooding and voids the warranty. To avoid condensation/corrosion problems, do so could result in your pool/spa system.
NOTE - If no wrenches). See Troubleshooting Guide. Failure to do...
All Max-Flo II models - Page 9
... page 11 of non-granulated liquid-type soap. Removing the Ceramic Seat (See Parts Diagram on page 11 of the ceramic facing out.
9. If tight, use this product. Seal Installation (See Parts Diagram on page 11 of this manual for pump component locations.)
6. Max-Flo II ™ Series
Page 9 of injury, do not permit children to use a small screwdriver to tap...
All Max-Flo II models - Page 10
... (item#10) onto the motor shaft in diagram 1 at bottom of the spring seal assembly with the matching holes in place, and lubricated. Replace if damaged). Gently wipe the black, polished surface of this manual for pump component locations.)
11. black polished surface facing toward the
polished surface of 16
10. Max-Flo II ™ Series
Page 10 of...
All Max-Flo II models - Page 11
Max-Flo II ™ Series
Replacement Parts
Parts Diagram
Page 11 of 16
Item #16: Optional with some models
SEE PARTS LISTING ON NEXT PAGE
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
All Max-Flo II models - Page 12
... 115/230V)
SPX2707Z2M Motor, 1 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V)
SPX2710Z2M Motor, 1-1/2 HP, Two Speed, Threaded Shaft
1
(Single Phase, 60 Cycle 115/230V)
SPX2715Z2M Motor, 2 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V)
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II ™ Series
Parts Listing
Page 12 of...
All Max-Flo II models - Page 13
... to correct cause of "Shaft Seal Change Instructions" in suction. Empty pump/strainer housing. Tighten cover. 5. If pump develops a vacuum, check for debris. b. Max-Flo II ™ Series
Page 13 of obstruction. open the pump and remove the debris. Reset tripped breakers or replace blown fuses. 2. Impeller jammed with the wiring diagram on pool wall. 3. Lubricant will...
All Max-Flo II models - Page 15
... E-mail Address
Product Purchased Product Serial No
□ New Installation
□ Replacement
Type of In-Ground Pool:
□ Vinyl □ Fiberglass □ Gunite
Size of purchase.
Pump housing/strainers which fail or become defective during the warranty period, except as the result of purchase/installation. Max-Flo II ™ Series
___
Page 15 of purchase.
All Max-Flo II models - Page 16
Max-Flo II ™ Series
___
Page 16 of 16
This Page is Blank
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Hayward Max-Flo II® Reviews
We have not received any reviews for Hayward yet.