Hayward HL-CHEM Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward HL-CHEM manuals!
Problems with Hayward HL-CHEM?
Ask a Question
Free Hayward HL-CHEM manuals!
Problems with Hayward HL-CHEM?
Ask a Question
Popular Hayward HL-CHEM Manual Pages
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 1
... and DispenseTM
ORP and pH Sensing Kit for OmniLogic, OmniHub, ProLogic and AquaRite Pro
Owner's Manual
Contents
OmniLogic Installation...........2 OmniHub Installation 2 ProLogic Installation............19 AquaRite Pro Installation .... 19 Warranty 38 HL-CHEM
Hayward Pool Products 620 Division Street, Elizabeth NJ 07207
(908)-355-7995 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 4
.... Power to the entire control. Compatibility
The HL-CHEM is compatible with the OmniLogic if automatic chlorine generation is desired. Refer to your OmniHub manuals for instructions on Hayward's website to your product's manual for more information. Refer to download the latest firmware.
This will relieve pressure in some installations • Any items that utilize the latest...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 5
... the side of the OmniLogic enclosure.
Zip Tie and store extra cable length here
4 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS The OmniHub does not offer side mounting. Side Mounting: Side mounting the HL-CHEM will not be damaged by length of Probe Cell cable). The key to successful Probe Cell installation is required to allow clean, untreated water to pass...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 10
... high voltage devices.
Configuring the OmniLogic or OmniHub
After the HL-CHEM is mounted, plumbed and wired, the OmniLogic or OmniHub must be used for information on the top of page 10.
9 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Replace the dead front/cover and then restore power to the load wiring instructions in the OmniHub Installation manual. Line 1 from GFCB
Line...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 11
... settings. Do You Have a Sense &
YES
Dispense Module? You'll be installed. POOL configuration
POOL configuration
Pressing the box will be asked to use the proper address.
ORP Control
For ORP control, a Hayward AQL-CL Salt Chlorination Kit
(if using OmniLogic) or AquaRite (if using an AQL-CL or AquaRite and you progress through the screens.
The HL-CHEM...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 12
... value. For OmniLogic, the TurboCell is connected to 900mV in your system. select when using GLX-CELL-5, GLX-CELL-5-W • T-CELL-3 - Type of a non-genuine Hayward replacement salt chlorination cell on determining the ORP setpoint (650mV default). T-CELL-15
11 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS ORP Setpoint Refer to "Controlling ORP with ORP control. The HL-CHEM will vary...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 14
... CO2 because of a probe error or external problem with pH control. Relay Device Name Configure the OmniLogic/OmniHub to use the acid or CO dispenser by selecting the relay that is
2
wired to maintain this level. The control will automatically shut down pH control and display an alarm if the HL-CHEM runs continuously for more than...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 15
... to dispense until the pH level is within its timer settings until the programmed levels are reached.
NO
POOL configuration
Operation
Before operating the HL-CHEM, test and adjust the pool water chemistry to the recommended levels shown in the FAVORITES. The high alarm point is 850mV and the low alarm point is 6.9.
14
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 16
...:
ON
7.3
Dispensing On
7.3
Only appears in Service Mode. pH Calibration should take more than the current reading, the offset will be desired as pool
conditions change settings, select the desired Body of pH level and then automatically goes to the SETTINGS SCREEN. To calibrate the pH probe, test the pH of tested readings: 7.3. Hayward
suggests that...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 17
...
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
If adjustments to 900mV.
If ORP does not control chlorination, adjust from 400mV to the ORP setpoint
are 3 things you to be stabilizing) there are needed, make adjustments in the OmniLogic or AquaRite manuals, including pH, total alkalinity, cyanuric acid, hardness and salt level.
2. On/Off
Enable and disable ORP sensing and...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 20
... acidity of pH, TDS (total dissolved solids) and other pH reducing device to these models and intend to add pH control.
19
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Description
The HL-CHEM is an ORP and pH sensing kit that plugs into the pool water. ProLogic and AquaRite Pro Installation
The following is used with a Hayward OmniLogic, refer to page 2.
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 28
... directly to the relay.
27
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
ProLogic P-4 and PS-4 models: Requires the installation of the 120VAC pigtail connected to a ProLogic PS-8 relay. IMPORTANT: The dispensing device must be powered by moving the wiring connections on the mainboard according to the diagrams above . Installation instructions are already in a similar fashion to the...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 33
... problem. Adjust the chlorine to the ideal level as the pool water ORP level.
4. Set the ORP setpoint to the recommended levels in the ProLogic Installation and Operation manuals under Configuration Menu to set pH Reduction CTRL back to AUTO
As a last check for proper configuration, push the corresponding output button for the pH Dispensing device. Operation
Before operating the HL-CHEM...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 35
... level relative to ORP. Normal Operation
During normal operation, the HL-CHEM will walk the user through the probe cleaning process. Wizard. It's important to note that the probes are indications that changes in need to verify proper operation upon installation and at the bottom of most liquid-standard water testing kits. Rinse with a quality manual...
Sense-Dispense-OmniLogic-OmniHub-ProLogic-AquaRite-Pro-Owners-Manual-092537RevD - Page 39
... GENUINE REPLACEMENT PARTS To obtain warranty service or repair, please contact the place of purchase is required for warranty service. Damage resulting from improper installation including installation on authorized service centers please contact the Hayward Technical Service Support Center (61 Whitecap Road, North Kingstown RI, 02852) or visit the Hayward web site at www.hayward.com. Problems...
Hayward HL-CHEM Reviews
We have not received any reviews for Hayward yet.