Specifications
Page 45
... removing the jumper blocks at E-F. To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at A-B or C-D position does not affect any selection of Device or Cable Selection mode. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 37 In the CSEL mode the drive address is determined...
... removing the jumper blocks at E-F. To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at A-B or C-D position does not affect any selection of Device or Cable Selection mode. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 37 In the CSEL mode the drive address is determined...
Specifications
Page 46
When CSEL is 1 (Device 1). To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is open or at E-F. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 38 In the CSEL mode, the drive address is determined ...by AT interface signal #28 CSEL as follows: When CSEL is 0 (Device 0). In CSEL mode, installing or removing the jumper blocks at a...
When CSEL is 1 (Device 1). To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is open or at E-F. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 38 In the CSEL mode, the drive address is determined ...by AT interface signal #28 CSEL as follows: When CSEL is 0 (Device 0). In CSEL mode, installing or removing the jumper blocks at a...
Specifications
Page 48
... • When CSEL is grounded or at a low level, the drive address is 0 (Device 0). • When CSEL is open or at E-F. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 40 Refer to spin up is 1 (Device 1). Command to 10.37 Set Features. 5.3.4.4 Power ...below shows the jumper positions used for Disabling Auto Spin Notes: 1. 2. 3. To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is SET FEATURES (subcommand 07h). These jumper settings are used. I GECA HFDB DEVICE 0 (Master) I GECA...
... • When CSEL is grounded or at a low level, the drive address is 0 (Device 0). • When CSEL is open or at E-F. HITACHI Deskstar & CinemaStar P7K500 Hard Disk Drive specification (Rev 1.1) 40 Refer to spin up is 1 (Device 1). Command to 10.37 Set Features. 5.3.4.4 Power ...below shows the jumper positions used for Disabling Auto Spin Notes: 1. 2. 3. To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is SET FEATURES (subcommand 07h). These jumper settings are used. I GECA HFDB DEVICE 0 (Master) I GECA...
Specifications
Page 64
MIC standards are based technically on CISPR22:1993-12 measurement standards and limits. 5.12 Electromagnetic compatibility When installed in conformity with a random accessing routine at maximum data rate, the drive meets the following worldwide EMC requirements: United States ...76/889 related to electromagnetic compatibility. 5.12.2 C-Tick Mark The product complies with the following EC directives under the sole responsibility of Hitachi Global Storage Technologies Japan Ltd: Council Directive 2004/108/EC on the approximation of laws of the Member States relating to the control of...
MIC standards are based technically on CISPR22:1993-12 measurement standards and limits. 5.12 Electromagnetic compatibility When installed in conformity with a random accessing routine at maximum data rate, the drive meets the following worldwide EMC requirements: United States ...76/889 related to electromagnetic compatibility. 5.12.2 C-Tick Mark The product complies with the following EC directives under the sole responsibility of Hitachi Global Storage Technologies Japan Ltd: Council Directive 2004/108/EC on the approximation of laws of the Member States relating to the control of...