Honeywell 4600RSF051CE Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell 4600RSF051CE manuals!
Problems with Honeywell 4600RSF051CE?
Ask a Question
Free Honeywell 4600RSF051CE manuals!
Problems with Honeywell 4600RSF051CE?
Ask a Question
Popular Honeywell 4600RSF051CE Manual Pages
User Guide - Page 2
...part of this publication does not represent a commitment on the part of HII. Web Address: www.honeywell...generates, uses, and can radiate radio frequency energy and, if not installed
Disclaimer
Honeywell International Inc. ("HII") reserves the right to make changes in specifications....
nor for technical or editorial errors or omissions contained herein;
This device must accept ...
User Guide - Page 7
... of Contents
Chapter 1 - Terminal Interfaces
Terminal ID 2-1 Supported Terminals 2-2 Keyboard Country 2-4 Keyboard Style 2-6
i Plug and...Connection 1-12 Wand Emulation Connection 1-13 Menu Barcode Security Settings 1-14 Reading Techniques 1-15
Chapter 2 - Getting Started
About This Manual 1-1 Unpacking the Imager 1-1 Imager Models 1-2 Imager Identification 1-3 Connecting the Imager with ...
User Guide - Page 17
... Imager After you need to an option indicates the default setting. 1 Getting Started About This Manual This User's Guide provides installation and programming instructions for damage during shipment. Product specifications, dimensions, warranty, and customer support information are factory programmed for later storage or shipping.
1 - 1 Honeywell barcode imagers are also included.
User Guide - Page 20
... page 1-8. 6. The imager beeps once. If this manual. Program the imager for a keyboard wedge interface to an IBM PC AT with Keyboard Wedge
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to your interface and you do not need to modify the settings, skip to a portable data terminal in the...
User Guide - Page 21
...barcodes beginning on page 1-2 to determine which interfaces apply to "USB Application Note," available at www.honeywell.com/aidc.
1 - 5 The imager beeps. 4. Verify the imager operation by scanning a barcode... refer to your imager. puter.
2.
Connecting the Imager with USB
Note: See "Imager Models" on page 1-9.
3. An imager can be connected to the com- Connect the appropriate interface...
User Guide - Page 22
... to set the baud rate and communications protocol.
1 - 6 Once the imager has been fully connected, power up the computer. 6. Connecting the Imager with RS-232 Serial Port
Note: See "Imager Models" on... page 1-2 to determine which interfaces apply to your imager. Connect the appropriate interface cable to the port.
4. Tighten the two screws to secure the connector to ...
User Guide - Page 30
Please contact the nearest technical support office (see Technical Assistance on page 2-12.)
Wand Emulation Plug & Play
(Code 39 Format)
Wand Emulation Plug & Play Same Code
Menu Barcode Security Settings
Honeywell 2D imagers are programmed by scanning menu barcodes or by sending serial commands to the imager. 25 inches per second, Output Polarity to black high, ...
User Guide - Page 45
... imager. Default = 40.
20
* 40
60
80
2 - 13 Default = Code 39 Format. Code 39 Format
Same Code Format
Wand Emulation
Note: See "Imager Models" on page 6-2). The Code 39 Format barcode below sets the terminal ID to 61, and the Same Code Format barcode sets the terminal ID to Code 39.
In Wand Emulation mode, the imager decodes the...
User Guide - Page 57
... Scan Stand, and Presentation, and Streaming Presentation Modes are effective in minimizing accidental rereads. Setting a reread delay protects against accidental rereads of the same barcode. You can read a barcode...) the imager reverts to manual trigger mode. Default = 5,000 ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the imager can set the time the imager should...
User Guide - Page 77
... (0-99), and the Save barcode using the Programming Chart inside the back cover of this manual.
4 - 5 Scan the Save barcode using the Programming Chart inside the back cover of this delay, scan the Intercharacter Delay barcode, then set the number of steps to 99 steps (of 5 ms each character of up to...
User Guide - Page 89
... ID to your imager.
Note: Changing secondary wand emulation settings also changes the primary wand emulation settings (see Wand Emulation on page 6-1 to determine which interfaces apply to 64. Wand Emulation Same Code Format
Wand Emulation Code 39 Format
Wand Emulation Multi Block
Note: See "Imager Models" on page 2-13). Default = 50ms.
5ms 150ms
* 50ms...
User Guide - Page 93
... free mode, the imager changes to the original hands free mode.
Programming Low Power Time-Out in the secondary interface also programs it in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the imager reverts...
User Guide - Page 100
... them to the host computer.
Minimum and Maximum lengths = 0-48.
When Check Character is set to Validate, but Don't Transmit, the unit only reads Code 39 barcodes printed with a check character, but Don't Transmit
Validate and Transmit
Code 39 Message Length
Scan the barcodes below to change the message length. The imager transmits...
User Guide - Page 194
...-Out" on page 3-4 for each of the menu commands (indicated by sending the Manual/ Serial Menu Command (page 12-9).
Selection
Setting * Indicates default
Factory Default Settings
Default
Terminal Interfaces
Terminal ID
000 (4600g/4600r/4600rp/ 4800i 030 models) 124 (4600g/4600r/4600rp/ 4800i 050 models)
Serial Command # Indicates a numeric entry
DEFALT
Page 12-4
TERMID###
2-1
12...
User Guide - Page 203
... Emulation Idle Data Block Size
Secondary Trigger Model
Wand Emulation Same Code Format Wand Emulation Code 39 Format 5 ms *50 ms 150 ms 500 ms On *Off 10 *25 40 80 120 150 200 *Black High White High *Idle High Idle Low 20 *40 60 80 *Manual/Serial Trigger Read Time-Out (0 - 300,000...
Honeywell 4600RSF051CE Reviews
We have not received any reviews for Honeywell yet.