IBM 4247-003 Support and Manuals
Get Help and Manuals for this IBM item
View All Support Options Below
Free IBM 4247-003 manuals!
Problems with IBM 4247-003?
Ask a Question
Free IBM 4247-003 manuals!
Problems with IBM 4247-003?
Ask a Question
Most Recent IBM 4247-003 Questions
Printing To Lightly On 4247 003
How do I make it print darker on all carbon copies?
How do I make it print darker on all carbon copies?
(Posted by hohmanm 11 years ago)
How Can I Get The Service Manual For Ibm 4247-003 Printer
(Posted by badjacodjoe 12 years ago)
Popular IBM 4247-003 Manual Pages
Maintenance Manual - Page 3
... 70 MAP 0150: Power Supply 75 MAP 0160: Ribbon Feed and Ribbon Lift 89
© Copyright IBM Corp. 1995, 2001
3 Contents
Safety Information 9 Safety Notices 9 General Safety 11 Electrical Safety 13 Pre-Service Inspection 15
Related Publications 17 Model A00 Publications 17 Models 001 and 002 Publications 17 Model 003 Publications 18 Common Publications 18
Preface - What's New...
Maintenance Manual - Page 24
... 001, 002, and 003 Error
action. Is this is a Model A00, see "How To Print the Printer Demonstration" on page 25.
in
Error Messages" on page 146, and perform the action suggested.
Is the problem no print? Locate the Model
"Reference Table 1, Model A00 001, 002, or 003 message in the display, such as
4247 User's Guide for other
informational messages...
Maintenance Manual - Page 32
... 001 and 002" on page 370. Model 003" on page 366.
003, see "How To Run the Test and
Diagnostic (T&D) Programs" on
correct printer operation, For Model - page 201. Information - Diagnosing Problems 32 For Models 001 or 002, see "How
(T&D) Programs" on page 161. For Models 001, 002, or
Install a new stacker assembly.
Install a new logic board. Diagnostic (T&D) Programs" on...
Maintenance Manual - Page 33
...Notes: 1.
a Model 003 with parallel only - Model A00: In the Program Configuration Setup, scroll to a 4247 User's Guide for a Model 003 with a serial attachment card. 2. Refer to HEX DUMP=NO. Model 003: On the operator panel, press the Hex Print key. A computer, such as a laptop, can be in hexadecimal code is the correct MAP for instructions. 3. Diagnosing Problems 33...
Maintenance Manual - Page 46
... must have the parallel loop-back connector (PN 08H7269) for this printer? See "T&D Error Messages and Actions -
Go to find the message. Go to step 7. See "Logic Board - Model 003" on page 201. Run T&D06 in Single Test Mode to verify correct printer operation. Install a new host parallel Record the message and go to test the...
Maintenance Manual - Page 65
... "Logic Board -
Chapter 1. Diagnosing Problems 65 For Model
page 378. page 447. Table 8. Is the measurement correct for both windings? Models 001 and 002" on page 201. and Diagnostic (T&D) Programs"
- Yes
No
Install a new logic board. For page 447.
A00, see "How To Run the Test and Diagnostic (T&D) Programs" on printer operation. the Test and...
Maintenance Manual - Page 110
... on page 112 for pull mode and push mode.
Go to step 14 on page 112. Diagnosing Problems 110
Table 15. Are the forms jamming into the platen during a Load Go to step 17 on... page 111. Check that the rear tractor is open or removed. rear tractor paper door is installed correctly, and the Go to step 16 on configuring the tractor. The following figure shows the positions...
Maintenance Manual - Page 129
... service. Or "Logic Board -
d. Check the printhead cables.
MAP 0200: 55 AFTA Errors (continued)
Step Questions/Actions
Yes
No
2. a. Remove the printhead.
c.
Mount forms, and try loading and parking forms several times. Are the cables OK?
3. Install a new logic board. For Return the printer to step 3.
Models 001 and 002" on
page 378.
Diagnosing Problems...
Maintenance Manual - Page 140
.... Model 003" on page 366.
052 MACHINE CHECK ERR XXX
Firmware error in supervisor code. Power off and power on the printer. See "Logic Board - Power off and power on the printer.
Diagnosing Problems 140 Models 001 and 002" on page 378. Models 001 and 002" on page 378. Or "Logic Board - If message remains, install a new Logic Board. If
of ribbon...
Maintenance Manual - Page 142
... installed correctly. If message remains, see IBM 4247 Printer Models 001, 002 User's Guide, SA24-4408).
2. Chapter 1.
Always lock the operator panel after completing your service procedures by performing this procedure. Error Messages for Models 001, 002, and 003 (continued)
Message
Description
Action
070 PRINTER BOARD CHANGED VERIFY CONFIGURATION SETTINGS
Occurs when printer...
Maintenance Manual - Page 144
...
This will be from the base code, the
the Model 003" on the operator's panel. If error reoccurs, replace logic board,
see "Logic Board - Flashing the Memory of
problem may be displayed
on page 549.
See "Attachment Card Guide Assembly with the Interposer
Connector (Model 003)" on page 366. Chapter 1. After the code transfer is
installation of attachment card was previously...
Maintenance Manual - Page 154
... board jumper that enables pin 18 voltage is installed correctly. Go to Step 2 on page 61. NPS 540+ with error messages
Probable Cause Internal errors
Action
1. Remove NPS from printer's parallel connector. 2. b. Wrong token ring speed. Disconnect the power cable at the unit. If the problem continues, replace the NPS unit or LAN card.
2. If the...
Maintenance Manual - Page 193
.... Run T&D21 to verify sensor
operation. Model A00" on page 441.
Replace the sensor cable assembly. If sensors are not operational: v Replace the logic board. Model A00" on page 441. See "Sensor Cable Assembly" on page 370. 3. See "Paper Path Service Checks"
on page 403. 2.
Replace the ribbon drive motor. See "Ribbon Drive Motor" on page 301. 3.
Diagnostics...
Maintenance Manual - Page 198
... print each of 8 Code Description entries. When a ninth Code Description is encountered, the oldest entry is deleted from the Print Error Log, and the new entry is displayed. Chapter 2.
Press the
Menu key until the 'Printer Configuration' test is displayed below '4247 OPERATOR TESTS'. 5. To print a custom set on the Model 003 and later
Models of blank letter or...
Maintenance Manual - Page 499
...set on the Model 003 and later
Models of configuration information found here: v "Coax Attachment Configuration" on page 517, contains all other possible configuration information. Press the
Menu key until 'Print Custom Sets' is displayed. Unlocking and Locking Printer...Stop key to locked.
Use the manual sheet feed to unlock or lock the printer configuration menu. 1. Press the ...
IBM 4247-003 Reviews
We have not received any reviews for IBM yet.