Icom IP501M Support and Manuals
Icom IP501M Videos
Popular Icom IP501M Manual Pages
Instruction Manual - Page 1
... track down the source of the problem, repair it, and then replace the damaged fuse with FCC RF exposure compliance requirements, and should be obstructed. Icom is not responsible for the destruction,...25-pin type) Enables you to connect to install them according to avoid inadvertent use of more of Icom transceivers with the instruction manual, may occur. is attached.
CAUTION: NEVER ...
Instruction Manual - Page 2
...TX/RX] [MSG]
Function display Microphone jack
IP501M
[DIAL]
Operating keys
Option key [PTT]
Microphone...when a call
types. You can support more between the call is connected to an ... your signal: 1. x.x.xx/x
Connecting... 00002
Setting up the transceiver for satellites or calculating
position ...service area, or cannot receive the control signal, the (out-of the transceiver.
Operating Guide - Page 2
... Canceling function (TX only) LLThis document is described based on the IP501M firmware version 1.0.XX.
Features
••Communication throughout the Coverage of the art technology and craftsmanship. With proper care, this Icom product. No part of trouble-free operation.
INTRODUCTION
Thank you with Icom's state of LTE (4G) and 3G Network ••Built-in...
Operating Guide - Page 10
... when valid position data is received. ••Blinks when searching for satellites or calculating position data.
1-8 LLIf the IP501M has not been authenticated, is received. Blinks when a call or message is received. : All/Group Call : Talkgroup ...••Blinks when a call is displayed.
(out-of the service area, or cannot receive the control signal, the icon blinks.
Operating Guide - Page 12
x.x.xx/x
Connecting... 00002
Setting up the transceiver for the first time. IMPORTANT: To maximize the readability of your dealer ... mode, the [TX/RX] indicator lights orange.
Release the [pTT], then hold down again to adjust the audio output level. ip501M Ver. Transmitting: While holding down [pTT], speak at
your normal voice level. • The [TX/RX] indicator lights red while...
Operating Guide - Page 13
... log → Tx Call log → Rx Call log
3. Talkgroup call -to party from the Address book
The [Address] key can delete logs in the Set mode.
Operating Guide - Page 20
....
3-7 After pushing [PTT], the mute is ON. LLThis function is set by your dealer, or in the Set mode. It blinks until you reply. Icom is not responsible for the specified period of time. LL" " is ...as obstructions, weather condition, and so on. LLThis function is set by your dealer, or in the Set mode. DDP-Bell function
The P-Bell function sounds the notification tone when a call is ...
Operating Guide - Page 21
SET MODE
4 Section
Using the Set mode...4-2 DDBasic Set mode...4-2 DDDetailed Set mode...4-2 DDUsing the Set mode...4-2
Set mode items...4-3
4-1
Operating Guide - Page 23
... service area. (Out-of -Area Warning Beep.
Selects whether or not to enable the tone that indicates an individual call receive notification type.
4 set mode
Set... result is also displayed on the transceiverʼs version or presettings.
Updates the transceiverʼs firmware.
Sets the Call Termination beep. Resets the transceiver to delete.
LLSelect "YES...
Operating Guide - Page 24
...that is preset by your voice.
-12 dB (lowest) ~ 12 dB (highest) (in the Basic Set mode. Enable
Selects a Destination ID display option. LLItems or default values may be different, depending on the... only when an optional HM-230HB is attached.
0 (lowest) ~ 31 (highest) 31
Sets the microphone sensitivity.
LLCommonly used for an earphone MIC, and headset. RX Buffer Type Call Type ...
Operating Guide - Page 26
... a beep when the Disable or Enable [PTT] on the transceiverʼs version or presettings. UTC Offset*3
Set the offset time between the UTC (Universal -14:00 ~ +14:00
Time Coordinated) and local time.
..._ _ _ (SIM1)
*1Displayed only when "Enable" is selected in the Basic Set mode. 4 set mode
Set mode items
The shaded items are talking. LLPush [PTT] to talk, and push again to return ...
Operating Guide - Page 27
...details. Search
LLDisplayed only when "User select" is connected.
version, if it is selected in the Basic Set mode.
LTE Unit Version Displays the internal LTE unit version.
-
- Phone Number Displays the SIM card's...Version Displays an optional HM-230HBʼs firmware
-
-
4 set mode
Set mode items
The shaded items are also displayed in the "Network Select" item.
Operating Guide - Page 30
...on the HM-230HB work as the same as the keys on the
presetting. Turn OFF
Microphone jack
IP501M
■■Panel description
Option key [Emergency] Microphone Option key [P1]
[PTT] switch
Option ...squelch
is open ••Lights orange: T ransmitting and receiving
in the menu, Address, Call History, Set mode, and so on. ••Push [◄] or [►] to select an item, and ...
Operating Guide - Page 35
...;The indicator turns OFF.
3. In the Standby screen, hold down [FUNC] for 3 seconds again, to enter the Detailed Set mode. 3. Rotate [DIAL] to select "Init BT Unit." 4. Push [Call History].
••The pairing list is...Bluetooth® device
■■Initializing the Pairing lists
If you have problems with Bluetooth operation, initialize the pairing lists, as shown below.
Operating Guide - Page 37
...set too low.
- No sound comes from the speaker. ••Volume level is located out of the service area. (" " blinks.)
-
Wait for repair... your location. - Find the cause, repair, and then replace the fuse. Set the volume to a suitable level in the... registered to a malfunction. 6 FOR YOUR REFERENCE
Troubleshooting
The following conditions are other active Bluetooth devices nearby...
Icom IP501M Reviews
Do you have an experience with the Icom IP501M that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!