Icom IP740D Support and Manuals
Get Help and Manuals for this Icom item
Icom IP740D Videos
Temps d'allumage des postes Icom IP740D et IP501H
Duration: 3:01
Total Views: 119
Duration: 3:01
Total Views: 119
IP730D/IP740D de Hybride IP-portofoon van Icom
Duration: 3:00
Total Views: 12
Duration: 3:00
Total Views: 12
Icom IP740D et DSD - Test de la partie NXDN
Duration: 14:06
Total Views: 447
Duration: 14:06
Total Views: 447
An introduction to the IP740D
Duration: 6:34
Total Views: 293
Duration: 6:34
Total Views: 293
Popular Icom IP740D Manual Pages
Instructions boxed With The Transceiver - Page 1
... protection appears defective, carefully clean the transceiver with any Icom or non-Icom equipment, if the malfunction is designed for and classified as this transceiver under license. INSTRUCTIONS
HYBRID IP TRANSCEIVER
IP730D IP740D
Thank you for choosing this product.
For Advanced features and instructions, see the INSTRUCTION MANUAL on . * O nly when the battery pack, antenna, and...
Instructions boxed With The Transceiver - Page 2
...when the transceiver downloading a new firmware.
LLTo turn ON the power. ••If the battery pack does not properly charge when it is out of the service area, or cannot receive a control...
(Not released, as of the power adapter.
* The shape may have some and green problems.
NOTE: ••The transceiver MUST be turned OFF while charging. Lights green:
Receiving or...
Instruction Manual - Page 1
INSTRUCTION MANUAL
HYBRID IP TRANSCEIVER
IP730D IP740D
INTRODUCTION 1 ACCESSORIES 2 BEFORE USING 3 USING THE CELLULAR MODE 4 USING THE IDAS MODE 5 OTHER FUNCTIONS 6 SET MODE 7 FOR YOUR REFERENCE
Instruction Manual - Page 2
..., disturbances, riots, war, or radioactive contamination. • The use of such marks by Bluetooth SIG, Inc. This instruction manual contains additional important operating instructions for the transceiver. and any use of Icom transceivers with any Icom or non-Icom equipment, if the malfunction is because of: • Force majeure, including, but not limited to , or performance...
Instruction Manual - Page 11
...;•Rotate to adjust the audio output level.
3-2 You can also assign functions in the Detailed Set mode (p. 6-5).
••Selects a preset address. (p. 3-3) ••Push to toggle ...mode selection, Talkgroup Selection, and so on*. *Selectable function may be assigned, depending on a Set mode setting.
••Rotate to turn the Key Lock function ON or OFF. (p. 2-4)
LL[PTT...
Instruction Manual - Page 17
...." 5. Rotate Rotary Selector or push [▲] or [▼] to select a SIM card to display the "SIM Selection" screen by your dealer, or in the Detailed Set mode (p. 6-8).
SET(Detail)
SIM Selection Carrier A (SIM1)
DDPocket Beep function
The Pocket beep function sounds a notification tone and indication when a call is received. LL" " is displayed...
Instruction Manual - Page 19
You can also assign functions in the Detailed Set mode. (p. 6-5)
••Push to display the Call-to party selection screen
•...times to select functions such as Operating mode selection, and so on*. *Selectable function may be assigned, depending on a Set mode setting.
••Rotate to turn ON or OFF the transceiver.
••Rotate to adjust the audio output level.
4-2...
Instruction Manual - Page 23
...(Example: Optional VS-3)
DDAbout the VS-3 Bluetooth headset
When you can operate with the IP730D or IP740D.
••If the headset does not work correctly, even if the power is approximately 10 ...device near such devices, interference may not be usable, depending on the Notice Tone settings or "BT PTT Beep" setting in the 2.4 GHz band that you use a Bluetooth device, pay attention to...
Instruction Manual - Page 24
.... Push [CLR/Lock] to cancel searching. ••If found, the device's name and BD address are displayed on the screen.
(Example: ICOM BT-002)
SET Bluetooth ON
SET Search BT Device ICOM BT-002
2. Turn OFF the transceiver, if it is displayed. 3. Rotate Rotary Selector or push [▲] or [▼] to select "Search...
Instruction Manual - Page 25
... the VS-3 for 3 seconds, to turn ON the transceiver.
••The Set Mode is displayed. Pairing List
ICOM BT-002 Unconnected
DDInitializing the Pairing lists
If you have problems with Bluetooth operation, initialize the pairing lists, as shown below.
SET
Init BT Unit Clear
Initializing the Pairing list of the transceiver LLAll the...
Instruction Manual - Page 27
..., the Emergency mode is tilted past the preset angle for the
ON Timer preset time. Icom is detected. Sends an Emergency call .
Sends an Emergency call . Acceleration
ON Timer
Reminder...
Time
If raised back from the preset angle towards the vertical position before the Reminder Timer set time expires, the Emergency mode is canceled. 5 OTHER FUNCTIONS
Using the Emergency Call function ...
Instruction Manual - Page 28
... ON Timer preset time�
L If a user pushes any key before the Reminder Timer set time expires, the Emergency mode is canceled�
Enters the Emergency mode. Time
If pushing... functions, depending on � Icom is not responsible for the ON Timer set time�
L If a user pushes any key, or moves the transceiver before the Reminder Timer set time expires, the Emergency mode ...
Instruction Manual - Page 35
Notify Vol. Updates the transceiverʼs firmware. NO or YES
Sets the call or message received notification volume.
0 ~ 32
Sets the Notification Beep level.
0 ~ 32
Selects ...," and then push [Call History]
to enable the Key-
Selects whether or not to update the firmware.
ON or OFF touch beep. The function automatically switches between receive and transmit by detecting ...
Instruction Manual - Page 39
...Selects whether or not to enable the tone that indicates an individual call Receive tone.
P-Bell or Pocket beep
Sets the number of -Area Warning Beep.
6 SET MODE
Set mode items (Continued)
The shaded items are not holding down [PTT], depending on the attached microphone. (p. ... call was successfully transmitted. The beep also sounds when the transceiver reenters the service area.
Instruction Manual - Page 52
...-
Rotate [VOL] to the system. (" " is set too low.
- Check the call -to party number or... Remove the battery pack from the transceiver, then charge it for repair. Firmly insert the plug. Restart the transceiver. Wait until the operator...7 FOR YOUR REFERENCE
Troubleshooting
The following conditions are locked.
- No power comes ON. ••Loose connection of the service area. (" " ...
Icom IP740D Reviews
We have not received any reviews for Icom yet.