Icom VE-PG4 Support and Manuals
Get Help and Manuals for this Icom item
Icom VE-PG4 Videos
Unboxing The Icom VE-PG4 RoIP Gateway Unit | Icom IP Network | Two Way Direct
Duration: 1:31
Total Views: 291
Duration: 1:31
Total Views: 291
VE-PG4 ????(ICOM)? RoIP??????(????????) ?????????
Duration: 1:34
Total Views: 66
Duration: 1:34
Total Views: 66
Introduction To The Icom VE-PG4 RoIP Gateway Unit | Radio Over IP Networks | Two Way Direct
Duration: 1:51
Total Views: 1,163
Duration: 1:51
Total Views: 1,163
Webinar #25/2020 - Especificaciones RoIP VE-PG4 ICOM
Duration: 59:52
Total Views: 259
Duration: 59:52
Total Views: 259
Popular Icom VE-PG4 Manual Pages
Installation Guide ver.1.34 - Page 6
...) The detailed references for the system requirements, the system setup basics, maintenance, and the specifications. It can be downloaded from the Icom website. INTRODUCTION
ABOUT THE CONSTRUCTION OF THE MANUAL
You can be downloaded from the Icom website. Installation guide (This manual, PDF type) Instructions for the settings in the RoIP Gateway setting screen.
v It can use the...
Installation Guide ver.1.34 - Page 9
... the VE-PG4 from the Icom website and install it to save the recorded audio on your PC. Only one with
password protection is required. LLThe VE-PG4 accepts up the data on the USB flash drive before connecting it on a data storage device through the USB
port. LLBe sure to back up to update the firmware. LLYou...
Installation Guide ver.1.34 - Page 94
... appropriate way, according to your situation.
••Pushing the button: When the settings screen cannot be accessed because the IP address or
password for the VE-PG4 is unknown.
••Using the setting screen:
When you cannot access the VE-PG4 setting screen, change your network, and so on, you can successfully access the...
Installation Guide ver.1.34 - Page 95
The IP address of the VE-PG4 will be reset to "192.168.0.1."
••V/RoIP Settings: Restores the factory defaults other than the settings in the Network Settings, Router Settings, and Management menus. Factory Defaults options ••All Settings: Restores all settings to the factory defaults. If the IP address and the password are unknown, see the...
Installation Guide ver.1.34 - Page 105
... [USB1]
has turned OFF
e Remove the USB flash drive
7 Confirm the firmware version of the VE-PG4, save it is completely rebooted. ••Before removing the USB flash drive, confirm the [USB] indicator is a specific folder of the VE-PG4 on the setting screen.
(TOP > System Status)
CAUTION:
••DO NOT remove the...
Installation Guide ver.1.34 - Page 112
...
••Parity:
None
••Stop:
1 bit
••Flow control: None
When the COM port setting is required. The USB driver for the Icom network devices is finished, press the [Enter] key to the manual. Download the USB driver and the manual from the Icom web site and install it according to display the "VE-PG4 login:" prompt.
6-5
Installation Guide ver.1.34 - Page 122
... your information
Using the Virtual serial port
Connection Port Settings > EXT I/O (EXT)
■■Preparation on the VE-PG4
Before using the virtual serial port, enable serial communication on the serial communication.
LLThe required settings on the VE-PG4 vary, depending on the setting on the VE-PG4. VE-PG4
Serial communication
device
[EXT3]
Connection cable OPC-2389...
Operating Guide ver.1.36 - Page 3
...It can be downloaded from the Icom website. Installation guide (PDF type) Instructions for the settings in the RoIP Gateway setting screen.
Operating guide (This manual, PDF type) The detailed references for the system requirements, the system setup basics, maintenance, and the specifications. Precations (Comes with the RoIP Gateway) Instructions for each device, that is connected...
Operating Guide ver.1.36 - Page 88
... letters, numbers, and symbols can be
used by another connection setting.
•• When [Transceiver Model] (2) is completed, you use to 31 characters. LLAfter the registration is set the port number that you must reboot the IP100H.
1 2 3 4
5
6 7 8
9 10
1 TRX No
2 Transceiver Model 3 Name 4 Unit ID 5 Password
6 Transceiver Port Number
Selects the number that the IP100H...
Operating Guide ver.1.36 - Page 427
LLWhen a SIM card is inserted, the Automatic Update Setting is not displayed.
1
2 3
1 Automatic Update
2 15 Management
Firmware Update screen
Management > Firmware Update
■■Automatic Update
The firmware can be automatically downloaded and updated.
Usb Driver Installation Guide - Page 1
http://www.icom.co.jp/world/support/ •• The Icom network device ...INSTALLING THE DRIVER 3
4.
OVERVIEW 1 System requirements 1
2. OVERVIEW
System requirements The following conditions: •• You have already downloaded the latest USB driver from the Icom Download Service website.
USB DRIVER
INSTALLATION GUIDE
For the Icom network devices
You can set up an Icom...
Usb Driver Installation Guide - Page 2
..., and then log in as the administrator.
•• Confirm no other application is installed, manually uninstall it before installing the latest driver. Before connecting to a PC
•• The USB driver does not support the automatic recognition system.
Once the driver has been installed, a PC software can be used by the PC.
•• When another network...
Usb Driver Installation Guide - Page 3
...Click (☞ Continued on the PC as the administrator. 3.
Double-click the following instructions, depending on your system version and settings.
6. Disconnect the cable, if connected, before starting the USB driver installation.
•• This USB driver does not support the automatic recognition system. LLThe displayed dialog, indications, or operations may differ slightly from...
Usb Driver Installation Guide - Page 5
... FOR YOUR REFERENCE
4-1 Terminal software setting
Do the following steps to access the network device with the device name is displayed. (For example: "VE-PG4> login:") LLAfter you have successfully ... control: None
Network device To the [CONSOLE] port
4. After installing the USB driver, set the serial port
settings in to the device, you can display the available command list by pressing the [Tab] ...
Usb Driver Installation Guide - Page 6
... the PC first, and then turn ON the device.
1. q Click
q Right-click
w Click
w Click
3.
FOR YOUR REFERENCE
4-2 COM Port setting
To change the COM Port number setting after you have installed the USB driver, connect the network device to close the screen. w Click
q Select 7. Right-click "Silicon Labs CP210x USB to UART Bridge (COM...
Icom VE-PG4 Reviews
We have not received any reviews for Icom yet.