Lexmark 11A7530 - Optra E+ B/W Laser Printer Support and Manuals
Get Help and Manuals for this Lexmark item
View All Support Options Below
Free Lexmark 11A7530 manuals!
Problems with Lexmark 11A7530?
Ask a Question
Free Lexmark 11A7530 manuals!
Problems with Lexmark 11A7530?
Ask a Question
Popular Lexmark 11A7530 Manual Pages
Service Manual - Page 17
.... PCL 5 is designed and manufactured by Lexmark International, Inc., to be compatible with the PCL 5 language. This means the printer recognizes PCL 5 commands used in the 4049 Technical Reference manual. Notices and Safety Information xvii Details relating to the commands.
This printer is Hewlett-Packard Company's designation of a set of their respective owners. AppleTalk and...
Service Manual - Page 23
...; "General Information" contains a general description of printer problems.
• "Repair Information" provides instructions for
individual FRUs. Special tools and test equipment are listed in this chapter.
• "Diagnostic Information" contains error code table, symptom
table, and service checks used to isolate failing field replaceable units (FRUs).
• "Diagnostic Aids" contains...
Service Manual - Page 26
This printer can be serviced without being connected to determine the symptom and repair the failure.
Use the error code charts, symptom index, service checks, and diagnostic aids to a host computer. 4049-XXX
Maintenance Approach
The diagnostic information in this manual leads you complete the repair, perform tests as needed to the correct field replaceable unit (FRU) or part. After you...
Service Manual - Page 27
...-Specific Integrated Circuit Customer Setup Dynamic Random Access Memory Electrically Erasable Programmable ReadOnly Memory Electrophotographic Process Electrostatic Discharge Field Replaceable ...Problem Isolation Charts Picture Element Power-On Reset Power-On Self Test Print Quality Enhancement Technology Raster Image Processor Read-Only Storage Static Random Access Memory Used Parts Replacement...
Service Manual - Page 30
... data on the printout matches the installed memory. If the error recurs replace the Flash SIMM. Flash problem at POR or while attempting to store pages is not supported by printer.
Defective font card installed in font slot.
The installed print cartridge is full.
Memory is detected by the ramp on the print cartridge as the cover closes.
Page too...
Service Manual - Page 31
... 6-3. These user codes are documented in the Setup Menu. See "Network Wrap Tests" on track 1 is bad. Diagnostic Information 2-4
If the test fails, the disk is closed. Replace the disk if instructed by entering the customer setup menu and selecting Serial Setup or Parallel Setup, Serial Buffer or Parallel Buffer, and changing the setting from the printer but the...
Service Manual - Page 48
... recorded as for possible problems. Refer the customer to the LaserPrinter Network Printer Utility Guide to find a printer or network problem, but jobs still do not print. Increasing the diagnostics mode Print Contrast setting will darken print further. this is too light before performing service.
Clean the transfer roll by a worn out print cartridge. Make sure Print Darkness...
Service Manual - Page 54
...printers do not support the Dual Rear Feeder without an upgrade. On the early machines engine board connector J5 is not, check the printer code levels (see Note above) and test the torquer. machines not requiring the adapter have continuity to support...Paper Feed Problem, Dual Rear Feeder
Run the diagnostics Paper Feed for Feeder 1 and Feeder 2.
Upgrade kits containing code upgrades and the...
Service Manual - Page 56
... or without the printer installed.
Clean rollers with alcohol or water;
Look between the two models. replace if necessary. 4049-XXX
Paper Feed Problem, High Capacity Feeder
The paper feed rollers should have excessive curl. For all paper in the high capacity feeder. Letter paper size and A4 paper size model feeders are not supported in the...
Service Manual - Page 69
... SIMM.
1. if necessary, reduce the setting further to clear the error log. 4. Select [Flash Test]. Verify that corrects the problem. Select [ERROR LOG]. 3. 4049-XXX
Error Log
The error log records the last six "2X Paper Jam" or "9XX Service" errors. If more than six errors are logged as 977.
1. If the same error occurs consecutively it is the oldest...
Service Manual - Page 72
... of Lexmark Technical Support. Select [PAGE COUNTS]. 3. Select [CANCEL] to the Envelope+ or 100-Sheet Auxiliary feeder. 4049-XXX
Note: "Feeder" refers to stop continuous. 6. Select [PAPER FEED TESTS]. 3. It can be implemented with the assistance of the Dual Rear Feeder.
1. Select [PRINTER SETUP]. 3.
"Feeder 1" and "Feeder 2" refer to diagnose parallel port interface problems...
Service Manual - Page 77
... Diagnostics mode. 2. Note: Install the parallel wrap plug part no. 1319128 for the parallel test or install the 25-pin serial wrap plug part no. 1329048 for instructions on running the Parallel Confidence Test. Select [CANCEL] to the Diagnostics mode main menu.
To run the Wrap Test:
1. Select [PRINTER SETUP]. 3.
4049-XXX
Transfer
This setting varies the transfer...
Service Manual - Page 139
...parts. Safety Inspection Guide
The purpose of this inspection guide. Use good judgment to identify possible safety conditions not covered by this inspection guide... for printer preventive maintenance.
Check the following items:
• Damaged, missing, or altered parts, especially...If any non-Lexmark attachments
Lubrication Specifications
Lubricate only when parts are replaced or as needed,...
Service Manual - Page 191
... 5-4 removal 4-15
envelope enhance 3-7 envelope print test 3-7 Envelope+ Feeder
envelope restraint spring adjustment 4-2
magnet adjustment 4-3 paper feed problem 2-26,
2-27 parts assembly 7-40, 7-42 error codes 2-2 ESD-sensitive parts 4-1 exit sensor board removal 4-16
F
fan (927 error) 2-18 fan/redrive
removal 4-17 features 1-1 flash test 3-8 frame
lower frame assembly removal 4-28
lower frame...
Service Manual - Page 192
...922 error 2-19 923 or 924 error 2-20 input guide removal 4-19 lamp removal 4-20 parts ...board removal
4-26
L
LAN information 3-17 problems 2-21
LCD test 3-9 light print 2-21 lubrication specifications 6-1 LVPS
cover removal 4-30 removal 4-29
...models available 1-1
N
network card 977 errors 2-21
network connectors 3-17 network wrap tests 2-22
Ethernet 10Base-2 2-22 Token-Ring 2-22
X-3 Service Manual
Lexmark 11A7530 Reviews
We have not received any reviews for Lexmark yet.