LiftMaster MAS Support and Manuals
Get Help and Manuals for this LiftMaster item
This item is in your list!
View All Support Options Below
Free LiftMaster MAS manuals!
Problems with LiftMaster MAS?
Ask a Question
Free LiftMaster MAS manuals!
Problems with LiftMaster MAS?
Ask a Question
Popular LiftMaster MAS Manual Pages
Owners Manual - Page 2
...OPERATION AND MAINTENANCE
Important Safety Instructions General Service Shear Pin Replacement Battery
ADDITIONAL FEATURES
Suggested Loop Sensor Locations Trap Instructions Sequence Access Management System (SAMS) with "Memory" Control Board Layout
TROUBLESHOOTING
Battery Checkout Gate Not Operating Troubleshooting Chart
REPAIR PARTS
Part Numbers and Descriptions Parts Shipped Mega Arm Tower Unique...
Owners Manual - Page 3
...servicing the general public. That means that is installed on this operator. Non-contact sensors such as an airport security area or other restricted access locations not servicing the general public, in which unauthorized access... garage or parking area associated therewith. Gate may move at least one of the four UL325 classes. SAFETY » UL325 MODEL CLASSIFICATIONS
UL325 MODEL ...
Owners Manual - Page 5
... foot x 3 inch tubular aluminum barrier arm
• Heater option MUST be needed.
• Wrench or Socket Set • Phillips Head Screwdriver • C Clamps
• Level • Small Screwdriver • T25 Torx Head Screwdriver
OPERATOR SPECIFICATIONS
This model is sensed at close loop.
• Anti-tail gate alarm - fires K1 relay to monitor arm...
Owners Manual - Page 9
... open position if it is re-opened. With S1 switch 5 on, this input becomes a momentary pulse open limit switch of the control board. When used as receivers, loop detectors, access controls... (COM) on the control board
C18 U18
C15
F
MANUAL
1 2 3 4 5 6 7 8 9 1Ø 11 12
OPEN Q2
J5
S3
T2
T4
T6
T8
T1
T3
T5
T7
CLOSE OPEN 1 OPEN 2 OPEN 3 R21
AUX 4 SAFETY 5 CLOSE 6 BACK 7...
Owners Manual - Page 10
...LiftMaster MBAT or 29-NP712 batteries. ALWAYS CONNECT AC POWER BEFORE INSTALLING BATTERIES.
1 Connect AC power BEFORE installing batteries. 2 Install...;
S2 12
BATTERY INSTALLATION CONNECTING THE BATTERY LEADS - Replace batteries in place. maximum...,Buzzers, and SAMS (Sequence Access Management System). K1 D11
U19...provide battery backed power to install batteries correctly will cause damage ...
Owners Manual - Page 12
... open /push to operate the gate.
TO ERASE ALL REMOTE CONTROL CODES
1 Press and hold the button on the receiver panel until completely closed.
THERE ARE NO OTHER USER SERVICEABLE PARTS.... steadily for changing the code setting or replacing the battery. Connect terminals 1 and 2 to door travel. • ALWAYS keep remote controls out of reach of moving gate or door. BAT- Repeat Steps ...
Owners Manual - Page 13
...THE BARRIER ARM DIP Switch S1-7
The J4 Motor Wiring is manually forced UP (OPEN), the barrier arm will activate throughout the OPEN cycle. For left .
5. when the barrier arm is controlled ...such as Counters, Alarms, Buzzers, and SAMS (Sequence Access Management System), can be used for variable amounts of time depending upon the settings of the Barrier Arm may be wired into terminal strip...
Owners Manual - Page 15
...) should be adjusted by a LiftMaster professional.
10. WARNING After any adjustment open position, time out (using the time delay set at the limits: Move the ... delay set at S-2 switches 1-5) and then close.
Have a qualified service person make repairs to detect obstructions. OPERATION AND MAINTENANCE » IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To...
Owners Manual - Page 16
... use a drill bit smaller than
light ones). 5. If drilling is loose or needs replacement, adjust with a number 6 taper...Replacement must be 27.5 +0.05, -0 Vdc disconnected (set with LiftMaster P/N MBAT batteries. Connect AC power and batteries. 10. Batteries are maintenance free.
Turn the S3 Manual Open switch to OPEN on the Control Board Layout page). BATTERY REPLACEMENT
Service...
Owners Manual - Page 18
...the OPEN input (J5 - ADDITIONAL FEATURES » TRAP INSTRUCTIONS
TRAP INSTRUCTIONS
INSTALL THE K1 AUXILIARY RELAY AND CONNECTOR AT MEGA ARM CONNECTED TO THE ACCESS DEVICE
1. SET THE DIP SWITCHES AT THE TRAP OPERATOR
1.
Set switch ...OFF
OFF
12345678
TRAP CONFIGURATION Must use trap kit. See Mega Arm Options Parts List
Close Loop Trap
Close Loop Trap
Close Loop
Close Loop
Card Reader...
Owners Manual - Page 19
...
Access Device
J5 #11 J5 #8
C
Extra Open Limit
Switch
NC
S1, #6 and #8 (ON) = K1 Relay PULSE only. NOTE: A separate open input. (WARNING: Max of dedicated/isolated dry contacts - {C. Tampering with the multiple vehicle memory count selection, use the K1 relay to raise if one set of 30 VOLTS at the other operator is 4 wires...
Owners Manual - Page 20
...ma. [1/2 amp]. Shows that processor and program are running properly. Free Exit Loop
Shadow Loop Commons - 0 Vdc
C18 U18
C15
Q6 Q5
Q4 D28
Open Limit Sensor Open Drivers On
Motor Brake On Close Drivers...AGAINST FIRE DX1 REPLACE ONLY WITH THE... opened or closed during service of operator. S3: Manual open....BOARD LAYOUT
Open Gate Inputs - Reader, Push Button Aux Open / Reset (Pulse Open/Close)
...
Owners Manual - Page 24
..., operation without notice.
01-60162H
HOW TO ORDER REPAIR PARTS OUR LARGE SERVICE ORGANIZATION SPANS AMERICA
INSTALLATION AND SERVICE INFORMATION SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-2806 www.liftmaster.com
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • PART NAME • MODEL NUMBER
ADDRESS ORDERS TO: THE CHAMBERLAIN GROUP, INC. In...
Quick Start Guide - Page 1
...50%.
If the barrier arm is to the right, it is set for right-hand gate operation.
• Motor speed is set to -Close, Single Button Function, and Fail Safe (Auto Open...operator default setting for DIP switch S1-7 is intended to the installation manual for complete information regarding installation and programming. QuickStart programming guide for MEGA Arm Gate Operators
MODELS MADCBB, ...
Quick Start Guide - Page 2
...+
PROTECTION
AGAINST FIRE
DX1
REPLACE ONLY
WITH THE SAME
TYPE ...manually forced UP (OPEN), the barrier arm will automatically OPEN approximately 15 seconds after the set amount of time elapses and the count memory is set... Alarms, Buzzers, and SAMS (Sequence Access Management System), can be in the ...it is reset to Close) will remain OPEN before CLOSING....batteries drop below 50% at which ...
LiftMaster MAS Reviews
Do you have an experience with the LiftMaster MAS that you would like to share?
Earn 750 points for your review!
We have not received any reviews for LiftMaster yet.
Earn 750 points for your review!