MSI E7505 Support and Manuals
Get Help and Manuals for this MSI item
Popular MSI E7505 Manual Pages
User Guide - Page 3
...® is a registered trademark of Phoenix Technologies Ltd. Alternatively, please try the following help resources for FAQ, technical guide, BIOS updates, driver updates, and other information: http://www.msi.com.tw/ Contact our technical staff at: support@msi.com.tw
iii AMI® is a registered trademark of American Megatrends Inc. Copyright Notice
The material in the preparation...
User Guide - Page 5
...iii Copyright Notice iii Revision History iii Technical Support iii Safety Instructions iv Chapter 1. Hardware Setup 2-1 Quick Components Guide 2-2 Central Processing Unit: CPU 2-3 CPU Installation Procedures 2-4 CPU Core Speed Derivation Procedure 2-5 Memory 2-6 Memory Speed/CPU FSB Support Matrix 2-6 DIMM Module Combination 2-6 Installing DDR Modules 2-7 Power Supply 2-8 SSI 24-Pin...
User Guide - Page 10
... x 1) provided by add-in ICH4 south bridge. Onboard LAN h Integrated Broadcom® BCM5703CKHB Gigabit Ethernet controller. h Mini PCI interface. On-Board Peripherals h On-Board Peripherals include:
- 1 x floppy port supports 2 FDDs with
PIO, Bus Master and Ultra DMA100/66/33 operation modes.
Onboard Audio h AC'97 audio codec integrated in card (Optional) - 4 x USB 2.0 ports (Rear...
User Guide - Page 21
... for 184-pin DDR DIMM (Double InLine Memory Module) modules and supports the memory size up to 8 GB. DDR DIMM Slots (DIMM 1~4)
Memory Speed/CPU FSB Support Matrix
DDR200 400MHz FSB Yes 533MHz FSB No
DDR266 Yes Yes
DIMM Module Combination
Install at least two DIMM modules on the DDR DIMM slots (DIMM 1~4). You...
User Guide - Page 30
... DMA 33/ 66/100 function. If you install two hard disks on cable, you must configure second hard drive to IDE1. Refer to Slave mode by setting the jumper accordingly.
IDE2 (Secondary IDE Connector) IDE2 can connect a Master and a Slave drive. MSI Reminds You... IDE1 can also connect a Master and a Slave drive. You must configure...
User Guide - Page 42
3. Hold the card lightly but firmly. Locate the supporters on the left end). Use long nose pliers to clip one on the right ...they lock onto the notches in the ends of the supporters and press it withdraws from the fixing hole.
Hardware Setup supporters
supporter
2-27 Push the retaining clips (on the card with the supporters and press the card carefully down until it downwards until...
User Guide - Page 49
.... Set Supervisor/User Password Use this menu to load the BIOS default values that are factory settings for minimal but stable system performance. Save & Exit Setup Save changes to set user and supervisor passwords. Load Fail-Safe Defaults Use this menu to CMOS and exit setup. BIOS Setup
PNP/PCI Configurations This entry appears if your system supports PnP...
User Guide - Page 50
...-only. through Dec.
day
Day of your drive must match with the drive table.
IDE Primary/Secondary Master/Slave Press PgUp/ or PgDn/ to Sat, determined by users. Note that you want (usually the ...to switch to the value you to set the system to the date that the specifications of the week, from Jan. Each category includes none, one or more setup items. Use the arrow keys to highlight...
User Guide - Page 51
...installed. The system doesn't stop for a disk error. Capacity
The formatted size of the landing zone. Landing Zone Cylinder location of the storage device.
If you select Manual, related information is asked to set the type of video adapter used for either a disk or a keyboard error.
3-7 Access Mode The settings...Write precompensation. BIOS Setup
will stop if an error is detected at ...
User Guide - Page 53
... drive. For example, if you to set the sequence of multi-threaded code running on Hyper-threading Technology, go to:
http://www.intel.com/info/hyperthreading
First/Second/Third Boot Device
The items allow you did not install a floppy drive, the setting "Floppy" does not show up.
3-9 BIOS Setup
processor can be executed.
For more...
User Guide - Page 55
...; operating system with DRAM larger than 64MB. Settings: 1.4, 1.1. When this setting is possible if you cannot run Setup. When you choose Non-OS2, you choose OS2. Setting options: Yes, No.
Small Logo(EPA) Show This item enables you to select the MPS version supported by your operating system. A password prompt appears every time when the computer...
User Guide - Page 57
... the number of DRAM installed.
Setting options: By SPD, Manual. This item applies only when synchronous DRAM is allowed for DRAM to be incomplete and DRAM may fail to this memory area, a system error may be allowed to
3-13 DRAM Data Integrity Mode Select ECC (Error-Checking & Correcting Code) or Non-ECC according to CAS# Delay...
User Guide - Page 58
... AGP for ISA cards. The setting you to manually set the AGP mode of the PCI memory address range dedicated to Thermal When the CPU temperature reaches a factory preset level... a system error may result. Delayed Transaction The chipset has an embedded 32-bit posted write buffer to the AGP without any program writes to support compliance with PCI specification version 2.1.
Setting options: 4...
User Guide - Page 61
... separately. IDE Primary/Secondary Master/Slave UDMA Ultra DMA implementation is also called block transfer, multiple commands or multiple sector read/write. Restores the system to use block mode;
BIOS Setup
Off On Former-Sts
Leaves the computer in the power off state. OnChip IDE Device Press to set a PIO (Programmed Input/Output...
User Guide - Page 72
... one company. Saying PCB version 1 is printed circuit board.
A: Please follow the special tech issue, http://www.msi.com.tw/support/
techexpress/special_tech/smartled.htm
Q: I install the fan directly to the motherboard? Can I used my MSI motherboard and got an error message, "Primary IDE Channel No 80 Conductor Cable Installed" while the system detected hard drives. T-1 Somewhere...
MSI E7505 Reviews
We have not received any reviews for MSI yet.