MSI Pro266TD Support and Manuals
Get Help and Manuals for this MSI item
View All Support Options Below
Free MSI Pro266TD manuals!
Problems with MSI Pro266TD?
Ask a Question
Free MSI Pro266TD manuals!
Problems with MSI Pro266TD?
Ask a Question
Popular MSI Pro266TD Manual Pages
User Manual - Page 2
... device, pursuant to part 15 of this equipment in a residential area is operated in accordance with the instruction manual, may cause harmful interference to correct the interference at his own expense. power cord, if any, must be required to radio communications.
Notice 2 Shielded interface cables and A.C. Micro-Star International MS-9105
Tested to comply with...
User Manual - Page 4
... the power inlet. 7. iv Safety Instructions
1. Place the power cord such ...Manual.
Keep this User's Manual for air convection hence protects the
equipment from humidity. 4. Make sure the voltage of breakage
12. Always Unplug the Power Cord before setting it . If any add-on the enclosure are for future reference. 3. Replace only with the same or equivalent type recommended by a
service...
User Manual - Page 5
... 1-1 Mainboard Specification 1-2 Mainboard Layout 1-4 Quick Components Guide 1-6 Key Features 1-7 MSI Special Features 1-8 D-LED 1-8
Chapter 2. CONTENTS
Chapter 1. Hardware Setup 2-1 Central Processing Unit: CPU 2-2 CPU Installation Procedures 2-3 CPU Core Speed Derivation Procedure 2-4 Memory 2-5 Introduction to DDR SDRAM 2-5 DIMM Modules Combination 2-6 Installing DIMM Modules...
User Manual - Page 8
...) chipset, the motherboard supports SINGLE/DUAL Intel® Pentium® III processors (FC-PGA/FC-PGA2) and is the standard version. As for Pro266TD Master series: Pro266TD Master and Pro266TD Master-LR. This chapter includes the following topics:
Mainboard Specification
1-2
Mainboard Layout
1-4
Quick Components Guide
1-6
Key Features
1-7
MSI Special Features
1-8
1-1 Introduction...
User Manual - Page 10
.../ASKIR/HPSIR.
Dimension z ATX Form Factor: 30.4cm x 25.4cm
Mounting z 9 mounting holes, 6 Layers
1-3
z Can connect up to four IDE devices
Promise 20265R On-Board (Pro266TD Master-LR only) z Supports IDE RAID 0, 1 z Can connect up to four IDE devices
On-Board Peripherals z On-Board Peripherals include:
- 1 floppy port...
User Manual - Page 14
... z I/O: 2 serial ports, 1 parallel port, 6 USB 1.1 ports, 1 floppy port, 1 IrDA
connector, 2 IDE RAID connectors (Pro266TD Master-LR only), 1 LAN jack (Pro266TD Master-LR only)
z D-LED™ -- 4 Diagnostics LEDs embedded on the mainboard z LAN Wake up Function z Modem (External/Internal) Ring Wake up Function z Promise 20265R Onboard with support for IDE RAID 0, 1 (Pro266TD
Master-LR only)
1-7
User Manual - Page 24
Chapter 2
Back Panel
The Back Panel provides the following connectors:
LAN M o u s e (Pro266TD Master-LR only) Parallel
Keyboard USB
COM A
COM B
Mouse Connector
The mainboard provides a standard PS/2® mouse mini DIN connector for attaching a PS/2® mouse. You can ...
User Manual - Page 27
... Data Serial Out or Transmit Data Data Terminal Ready) Ground Data Set Ready Request To Send Clear To Send Ring Indicate
LAN (RJ-45) Jack (Pro266TD Master-LR)
The mainboard provides one standard RJ-45 jack for serial port COM A and COM B. Hardware Setup
Serial Port Connectors: COM A & COM B
The mainboard has two 9-pin male...
User Manual - Page 30
... for jumper setting instructions.
2-14 You can connect a Master and a Slave drive to the TIP hard disk documentation supplied by integrating two IDE RAID connectors that support PIO mode 0-4, Bus Master, and Ultra DMA 33/66/100 modes. Chapter 2
IDE RAID Connectors: IDE3 & IDE4 (Pro266TD Master-LR)
The mainboard offers a low-cost RAID (Redundant Array of the installed hard...
User Manual - Page 41
... removing expansion cards, make any necessary hardware or software settings for the throughput demands of throughputs: 1x (266Mbps), 2x (533Mbps) and 4x (1.07Gbps).
Hardware Setup
Slots
The motherboard provides five 32-bit Master PCI Bus Slots and one AGP slot. AGP is an interface specification designed for the expansion card, such as jumpers, switches...
User Manual - Page 57
... without any system error. Aperture is used to AGP without passing anything through system memory and improves 4X speed accordingly. Settings: 1X, 2X and 4X. AGP Driving Control The field is a portion of Accelerated Graphics Port (AGP) aperture. Choose 4X only if your AGP card supports the feature.
3-15
AWARD® BIOS Setup
AGP & P2P...
User Manual - Page 61
... secondary add-in IDE interface does not support prefetching. Primary/Secondary Master/Slave PIO The four fields allow you to the following:
3-19 SuperIO Device Press to enter the sub-menu screen similar to set a PIO (Programmed Input/Output) mode for each IDE device. AWARD® BIOS Setup
VIA OnChip IDE Device
OnChip IDE Channel0...
User Manual - Page 67
... configure the suspend mode manually. There are three options for the length of power saving and is not detected for choosing the setting in this field, the hard disk drive will be turned
off . Suspend Mode If system activity is related to the mode: Suspend Mode.
AWARD® BIOS Setup
the previous state when...
User Manual - Page 69
...The field is detected from power saving modes if activity is used to install a modem/LAN card supporting power on a scheduled time/date.
Settings: 0~31. Date (of the specified IRQ line. IRQs Activity Monitoring...the system to specify the date for RTC Alarm Resume. AWARD® BIOS Setup
peripheral or component is . Enables or disables the monitoring of Month) Use the field to ...
User Manual - Page 73
... of the item will issue a warning and allows you must set the item to prevent the CPU overheat problem.
This is available only if there is hardware monitoring mechanism onboard... message if the chassis was once opened. CMOS Setup Utility - AWARD® BIOS Setup
PC Health Status
This section is to specify a thermal limit for CPU. Settings: Disabled, 50°C/122°F, 53°...
MSI Pro266TD Reviews
We have not received any reviews for MSI yet.