Makita CT321RX Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita CT321RX manuals!
Problems with Makita CT321RX?
Ask a Question
Free Makita CT321RX manuals!
Problems with Makita CT321RX?
Ask a Question
Popular Makita CT321RX Manual Pages
DT03 Instruction Manual - Page 3
... use ) replace strict adherence to be sure you have the power tool repaired before making any con- Properly maintained cutting tools with water. Use of the power tool for misalignment or binding of moving parts, breakage of your skin. 6. When battery pack is not in use and care 1. Have your power tool serviced by...
DT03 Instruction Manual - Page 4
....
A battery short can explode in locations where the temperature may accidentally fall out of the model number
4 ENGLISH Do not store the tool and battery cartridge in a fire. 8.
SAVE THESE INSTRUCTIONS. Charge the battery cartridge before installing or removing of the cartridge. Always stop the application that the tool is switched off your...
DT03 Instruction Manual - Page 6
...and insert the driver bit into the sleeve as it with a screw. CAUTION: When not operating the tool, always set the reversing switch lever to secure the driver bit. This tool...comes to the instructions above. When the reversing switch lever is removed before carrying out any other driver bit/socket bit.
1
2
The proper fastening torque may damage the tool.
Installing hook
ASSEMBLY
...
DT03 Instruction Manual - Page 8
... trouble develop during this manual. If inspection shows the trouble is thoroughly inspected and tested before attempting to country. IN NO EVENT SHALL MAKITA BE...SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. 2. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts...
FD05/FD06 Instruction Manual - Page 3
...parts of the power tool is below when using only identical replacement
parts. Disconnect the plug from the power source and/or the battery pack from the power tool before use ) replace...driver drill safety warnings
1. Cutting accessory contacting a "live " and could burn your power tool serviced by a qualified repair person using the tool in this instruction manual...with specifically ...
FD05/FD06 Instruction Manual - Page 4
... completely. If electrolyte gets into place. Overcharging shortens the battery service life.
3. CAUTION: Do not install the battery cartridge forcibly. The tool will also void the Makita warranty for the Makita tool and charger. Be careful not to disposal of the button, it all instructions and cautionary markings on the tool. Use of non-genuine...
FD05/FD06 Instruction Manual - Page 5
...again to scratch the lens of lamp, or it to become overloaded. tridge into the tool, always check to see the source of the model number
1
2
1. Lamp
CAUTION: Do not look in a manner that causes it may differ slightly from the actual capacity.
1. The... runs again but stops soon. The lamp keeps on lighting while the switch trigger is equipped with "B" at a Makita service center.
FD05/FD06 Instruction Manual - Page 7
...Open
Turn the sleeve counterclockwise to the instructions above. Sleeve To install the driver bit, pull the sleeve in the direction of the arrow and insert the driver bit into the sleeve as far as ...off and the battery cartridge is convenient for temporarily hanging the tool.
Installing or removing driver bit/ socket bit
For Model FD06 (optional accessory)
1 2
1. Then release the sleeve to ...
FD05/FD06 Instruction Manual - Page 8
...speed up the drilling.
Driver bit Fit the driver bit holder into the workpiece.
Hold the tool firmly with a guide screw. The guide screw makes drilling easier by setting the reversing switch to ... red part on either right or left side and secure it is a tremendous force exerted on the tool will only serve to the tool. There is not locked completely.
Installing driver bit holder...
FD05/FD06 Instruction Manual - Page 9
... by Makita Authorized or Factory Service Centers, always using the holster, remove a driver bit/...Makita tool specified in the holster. The use is removed before placing it in this manual...repairs, any other maintenance or adjustment should be sure that the arrow points to the neutral position. Waist belt
2. Using holster
Optional accessory
CAUTION: When using Makita replacement parts...
FD05/FD06 Instruction Manual - Page 10
... or exclusion may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. If inspection shows the trouble is thoroughly inspected and tested before leaving the factory. IN NO EVENT SHALL...
DT03R1/Z Parts Breakdown - Page 2
....
1 PC.
1 PC.
2 PC.
2 PC.
1 PC.
2 PC.
1 PC.
1 PC.
1 PC.
1
1
2 PC.
0
1 PC.
1
1 PC.
1
(DT03R1)
1
(DT03R1)
2
(DT03R1)
1
(DT03R1)
2 PC. (DT03R1)
1 Model DT03R1/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
183B49-8 HOUSING SET
001 C10 252126-6 HEX. LOCKING NUT M4-7
001 D10
INC. 31
002
851G84-1 DT03 NAME PLATE
003
266429...
FD05R1/Z Parts Breakdown - Page 2
...
013
911003-8 PAN HEAD SCREW M3X6
014
183B50-3 HOUSING SET
014 C10 252126-6 HEX. LOCKING NUT M4-7
002 D10... PC.
1
1
(FD05R1)
1
(FD05R1)
2
(FD05R1)
1
(FD05R1)
2 PC. (FD05R1) Model FD05R1/Z Parts list
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
126233-0 SPEED CHANGE LEVER ASSEMBLY
001 C10 231433-0 COMPRESSION SPRING 4
002
183B50-3...
Makita DT03Z/DT03R1 New Tool Flyer English - Page 1
... as bare tool Model DT03Z
SPECIFICATIONS
Hex Shank No Load Speed (variable speed) Impacts Per Minute (variable speed) Maximum Torque Battery Overall Length Net Weight (with battery) UPC code (kit) UPC code (bare tool)
...Makita General Catalog or visit our website at only 6" long n Weighs only 2.3 lbs. of Max Torque in .lbs. 12V max CXT™ Lithium-Ion Cordless Impact Driver Kit
Model ...
Makita FD05Z/FD05R1 New Tool Flyer English - Page 1
...™ 3/8" Driver-Drill (Tool Only) (FD05Z) n (2) 12V max CXT™ Lithium-Ion 2.0Ah Battery (BL1021B) n 12V max CXT™ Lithium-Ion Charger (DC10WD) n Tool Case
*Also availabe as bare tool Model FD05Z
SPECIFICATIONS
Capacity (steel) Capacity (wood) No Load Speed (variable 2 speed) Maximum Torque Battery Overall length Voltage Net weight UPC code (kit) UPC code (bare tool...
Makita CT321RX Reviews
We have not received any reviews for Makita yet.