Makita EA4300FRDB Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita EA4300FRDB manuals!
Problems with Makita EA4300FRDB?
Ask a Question
Free Makita EA4300FRDB manuals!
Problems with Makita EA4300FRDB?
Ask a Question
Popular Makita EA4300FRDB Manual Pages
Instruction Manual - Page 2
... trouble-free operation, while the hand-saving anti-vibration system and ergonomic grips and controls make work easier, safer, and less tiring for models with a spring-loaded starting assist.
MAKITA chain saws EA3500F-EA4301F are conÞdent that you read this modern piece of the sprocket guard 27 Cleaning the guide bar 27 Replacing...
Instruction Manual - Page 4
...with special signal-coloured shoulder straps and is to be replaced after having consumed alcohol, drugs or medication.
- ...saws
This power chain saw may , however, use this instruction manual to make himself familiar with the characteristics of engine powered sawing...you are under the in good physical condition. If you are part of the prescribed equipment and must be worn. The kind of...
Instruction Manual - Page 5
... Fuel should not come in contact with any in this instruction manual (8). Fuel cannot be nearby
in fuel vapors. Putting into .... - Change the place before checking the chain tension, tightening the chain, replacing it with the chain saw . - Buy only as much as well (7).... if it must not be well supported and securely held. The guide bar and chain must be in contact...
Instruction Manual - Page 7
... the end of the bar for cutting (risk of the guide bar, the chain saw should withdraw backwards in the direction of... to the direction of fall without stumbling (the people should be supported on sloping ground the user of the notch.
- The trunk...this reason use the lower edge of the tree -
c) the bottom part of the trunk is notched perpendicular to be seriously damaged or torn.
...
Instruction Manual - Page 8
... All other than original MAKITA parts or accesories and guide bar/chain combinations or...instructions issued by MAKITA Service.
You will put
your location during car transportation to occur in the instruction manual. Ensure safe positioning of burns).
- When the saw over long distances the guide....
22
Perform only the maintenance and repair works described in the Þngers...
Instruction Manual - Page 9
... KWA = 2,5
EA4300F, EA4301F 42,4 ...Guide bar, length of kickback
18,1
18,3
3/8
3/8 .325
6
6
7
see the Extract from the spare-parts list
3/8 / 0,050 (1,3)
3/8, .325 / 0,050 (1,3)
35, 40
33, 35, 38, 40, 45
see the Extract from the spare-parts list
4,8 / 4,9 2)
4,8 / 4,9 2)
Packing
Your MAKITA chain saw comes delivered in equal part from idling, full-load and racing speed. 2) Models...
Instruction Manual - Page 19
.... In addition, a long service life and reliable operation with a higher octane value.
mix 50 parts gasoline with these substances repeatedly... The engine is available, you can cause starting problems and damage the engine.Purchase only that amount of ..." (Blauer Umweltschutz-Engel) for lubricating the chain and guide bar.
MAKITA high-performance two-stroke engine oil is available in 6-8...
Instruction Manual - Page 21
... the chain saw has been turned off it is on a suitable surface.
23
21 Pick one of the chain and guide bar will be reduced. Otherwise the service life of the three settings depending on a suitable surface. If the lubrication is normal for residual chain oil to drip from the oil feed system...
Instruction Manual - Page 23
... prevent carburetor icing in this test, turn the insert 180° so that the chain and guide
bar are not near anything).
6
Hold the front handle Þrmly, with high humidity, ... after it as shown for winter operation. Caution: If the chain does not stop immediately. Contact a MAKITA service centre.
Put the cover back on the rear grip. Start the engine as described above (have a ...
Instruction Manual - Page 24
...can lead to correct the idle speed! On some models, the adjusting screw (H) is imperative to engine damage!... is warm, with a clean air Þlter and properly installed guide bar and chain. If the saw chain moves in ): Idle... 180 degrees) prevents excessively rich carburetor settings. SERVICE
Do not undertake any adjustments to a MAKITA service centre! Adjusting the idle speed Turn...
Instruction Manual - Page 27
...and sprocket guard, see „Replacing the spark plug"). To install the guide bar, saw only after having assembled it completely and inspected. Remove the chain (2) and guide bar (3). NOTE:
The chain ... model) and clean out the interior with a suitable tool. NOTE:
Make sure there are important for your own safety and must be done by a MAKITA service centre.
4 32
SERVICE
Cleaning the guide ...
Instruction Manual - Page 33
... guide bar Empty and clean Run empty
Page
25-26
13, 27 31
25-26 13, 17
21 23
22
29 27 21, 27 24 10 32 32 32 30 10, 30 10
32
27
33 In case of damage, have repaired by a qualiÞed service centre immediately Sharpen regulary, replace in the instruction manual. Replace...
Instruction Manual - Page 34
... local dealer.
The MAKITA service centres have not been approved. • Use of guide bar and chain lengths which have all matters. Guarantee MAKITA guarantees the highest quality and will void all warranty claims.
Spare parts Reliable long-term operation, as well as all costs for damage caused by: • Disregard of the instruction manual. • Non...
Instruction Manual - Page 36
For repairs and replacement of other parts, see your MAKITA service centre. Extract from the spare parts list
Use only original MAKITA parts.
EA3500F, 3501F EA4300F, 4301F
3
2
1
4
5
6
15
17
16
23
14
13
10
11
12
7
9 8
19
21 18
20
22
27 28 29 30
31/32
25
33 26
36
Instruction Manual - Page 37
...10 195 160 050 1 Return spring pack, complete 11 195 160 030 1 Spring 12 195 160 020 1 Driver 13 195 160 060 1 Starter cable 3,5x900 mm 14 965 603 040 1 Spark plug 15 181 114 ...013 1 O-Ring 20 x 1,3 mm
37 EA3500F, 3501F EA4300F, 4301F
Pos. Extract from the spare parts list
Use only original MAKITA parts. Qty.
For repairs and replacement of other parts, see your MAKITA service centre.
Makita EA4300FRDB Reviews
We have not received any reviews for Makita yet.