Makita EA5000PRGG Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita EA5000PRGG manuals!
Problems with Makita EA5000PRGG?
Ask a Question
Free Makita EA5000PRGG manuals!
Problems with Makita EA5000PRGG?
Ask a Question
Popular Makita EA5000PRGG Manual Pages
EA5000P53G EA5000PR Instruction Manual - Page 2
... should be repaired or replaced by the manufacturer according to a MAKITA distribution center or service center as soon as required maintenance in the written instructions required by subsection (d) must be warranted for replacement as the problem exists.
You are responsible for the warranty period defined in materials and workmanship that causes the failure of a warranted part for...
EA5000P53G EA5000PR Instruction Manual - Page 4
... 37 Service, spare parts and guarantee 37-38 Troubleshooting 38 Extract...guide bar 31 Replacing the saw or other safety related precauti- Cardboard is a basic raw material and is important that you to read , fully understand and
carefully follow the instructions outlined in a protective cardboard box to accidents.
WARNING ! Careless or improper use of this operator's manual...
EA5000P53G EA5000PR Instruction Manual - Page 6
... a planned retreat path from your chain saw, use replacement bars and chains speci fied by the manufacturer or the equivalent.
Additional safety precautions
The following rules:
a)
Contact of the guide bar nose with any other than the items listed in the operator's manual maintenance instructions, should be avoided. Do not operate a chain...
EA5000P53G EA5000PR Instruction Manual - Page 9
... fuel before starting to avoid false setting the tensioning procedure must match each other (see chapter "Fuel" of this manual. Be absolutely sure that guide bar and chain are ) tightened securely... important. Do not allow it has to be followed as described in this manual).
6
5
WARNING! Fueling instructions Fuel your hands. Always shut off the engine and then tighten. Never attempt...
EA5000P53G EA5000PR Instruction Manual - Page 15
.... 23). Begin the felling cut slighty higher than the
length of the guide bar requires use of either the
sectioning or plunge-cut method. These methods
are poorly supported. Then cut horizontally through the hinge because you try to fall completely, set the saw , you may be injured. When the tree hangs or...
EA5000P53G EA5000PR Instruction Manual - Page 16
...saw plunge-cutting should be taken to the operator.
32
WARNING! 4. WARNING! Never permit another person to support the log off the ground (fig. 30). Seek the help of the limb.
There is cutting a log...are inexperienced with your leg or foot.
16 WARNING! 2.
Do not work with the nose of the guide bar. Do not stand on a log while limbing it -
3
Bucking
2
Bucking is an extreme...
EA5000P53G EA5000PR Instruction Manual - Page 17
.... 33, 34). Follow the maintenance and repair instructions in this manual. Chain saws with catalytic converter take longer...replace worn sprockets or chains. a blowdown area, fig. 35).
Do not attempt any maintenance work not described in the appropriate section of this manual... repair work (burn hazard)!
Only properly trained professionals should work performed by your MAKITA service ...
EA5000P53G EA5000PR Instruction Manual - Page 19
...Specific consumption at max. Do not operate this chain saw is capable of a cut
inch 16 / 18
Guide-bar type
see the Extract from the spare-parts list
Weight (fuel tank empty, without chain, guide.... when using other synthetic oil
50:1 (oil quality must be JASO FC or ISO-L-EGD)
Chain brake
engages manually or in (cm3)
3.1 (50.0)
Bore
inch (mm) 1.77 (45)
Stroke
inch (mm) 1.24 ...
EA5000P53G EA5000PR Instruction Manual - Page 22
...the chain brake manually, simply push the hand guard (1) forward (towards you (arrow 2) until the saw chain is installed to contact of the guide-bar tip with... your left hand (arrow 1).
B
2
1
1
Engaging the chain brake (braking)
If the kickback is sufficiently strong.
While doing so the chain brake must be turned over whenever replacing...
EA5000P53G EA5000PR Instruction Manual - Page 23
...life.
If your eyes, immediately wash them with 1 part oil.
50:1 when using MAKITA synthetic two-stroke engine...marked containers for lubricating the chain and guide bar. AVOID SKIN AND EYE CONTACT
...see a doctor immediately! In addition, a long service life and reliable operation with adhesive additive for ...is available, you can cause starting problems and damage the engine.Purchase only that...
EA5000P53G EA5000PR Instruction Manual - Page 25
.... Adjusting the chain lubrication
STOP
The engine must be reduced. The oil pump comes factory‑set to the oil spray!
Pay attention to the left for a time. Place the saw by ...saw (see a light oil trace because oil will be cleaned regularly. Otherwise the service life of the guide bar.
To adjust the supply rate, use an appropriate base).
The adjusting screw is...
EA5000P53G EA5000PR Instruction Manual - Page 27
...service center.
6
C
Working in winter
In order to operating temperature faster, heated air can be replaced... by a specal insert with your hand, until the chain brake engages. Remove the cover (see "Cleaning the air filter"). If the temperature is not done, the cylinder and piston can be taken from getting in this test, turn the insert 180° so that the chain and guide... part ...
EA5000P53G EA5000PR Instruction Manual - Page 31
... are important for damage, and clean them with a brush. CAUTION: Start the chain saw only after having assembled it completely and inspected.
For replacing the guide bar, chain, and sprocket see "Replacing the spark plug"). B) and clean the interior with a suitable tool.
7 2 65
SERVICE A
B
31 Cleaning the guide bar
CAUTION: Protective gloves must be worn.
EA5000P53G EA5000PR Instruction Manual - Page 37
...'s manual. Clean to ensure even wear of the chain saw
Saw chain
Chain brake
Guide bar
Starter cable
Clean exterior, check for damage. Failure to maintain good cooling air flow. Page
General
Chain saw must be performed only by a MAKITA service center. In case of damage, have repaired by a qualified service center immediately
Sharpen regulary, replace...
EA5000P53G EA5000PR Instruction Manual - Page 38
...repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. Troubleshooting...8226; Disregard of the operator's manual. • Non-performance of...parts are not original MAKITA parts, insofar as the safety of your chain saw by a MAKITA service center.
Oil‑pump adjusting screw incorrectly adjusted. Spare parts...
Makita EA5000PRGG Reviews
We have not received any reviews for Makita yet.