Makita XLT02 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XLT02 manuals!
Problems with Makita XLT02?
Ask a Question
Free Makita XLT02 manuals!
Problems with Makita XLT02?
Ask a Question
Popular Makita XLT02 Manual Pages
Makita DC18RC Instruction Manual - Page 3
...damaged, ask Makita authorized
service center to replace it stops adjusting to the guide of electric ...Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 - 60 HZ
D.C. 7.2 V - 18 V
0.88 kg (1.94 lbs)
0.77 kg (1.70 lbs)
• Manufacturer reserves the right to change specifications without supervision. 14. This manual contains important safety and operating instructions...
Makita DC18RC Instruction Manual - Page 4
...a long time in a location exposed to repair or maintenance, if the yellow warning light will...charger, which charging is too hot, charging will flash for charging Makita-battery cartridge. Trouble on the charger.
• Yellow light will begin after the... it may not accept a
full charge until after the cooling fan installed in the following cases. -
BL1430
BL1830
22
Note: • It...
XLT02Z Instruction Manual - Page 1
IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar. 1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Angle Impact Wrench Boulonneuse d'Angle à Chocs sans Fil Llave de Impacto
XLT02
014172
IMPORTANT: Read Before Using.
XLT02Z Instruction Manual - Page 2
...BL1840
• Due to our continuing program of research and development, the specifications herein are subject to follow the warnings and instructions may differ from heat, oil, sharp edges or moving parts. Use personal protective equipment. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XLT02
Capacities
Standard bolt High tensile bolt
M4 - M12 (5/32 " - 1/2") M4 - fastening...
XLT02Z Instruction Manual - Page 3
...only identical replacement parts. A ...instruction for your power tool serviced by poorly maintained power tools. 22. Keep handles dry, clean and free from the battery;
GEB049-2
CORDLESS IMPACT WRENCH SAFETY WARNINGS
1. Fasteners contacting a "live" wire may cause burns or a fire.
27. Wear ear protectors. 3. Always be sure you have the power tool repaired before installation...
XLT02Z Instruction Manual - Page 4
... of overheating, possible burns and even an explosion. 4. Overcharging shortens the battery service life. 3.
Red indicator 2. Battery cartridge
3
014173
• Always switch off...• Do not use a damaged battery. If you notice less tool power. 2. Install it fully until it all instructions and cautionary markings on the battery cartridge with room temperature at 10 ﾟ C - 40 ...
XLT02Z Instruction Manual - Page 5
...that causes it may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position.
5 Changing the direction of rotation. In .... The light automatically goes out 10 - 15 seconds after switch lever release, have tool serviced at a Makita service center. Reversing
switch lever
B
A
014168
This tool has a reversing switch to restart. Star...
XLT02Z Instruction Manual - Page 6
...the bolt or nut. Angle head
1
1. Anvil
2
2
008335
1. Hook (Accessory)
CAUTION: • When installing the hook, tighten the screw firmly.
Straight head
3
014169
The hook is removed before carrying out any work ... 45-degree increments). An incorrect size socket will match up with a screw. Installing or removing socket
Adjusting the angle head The angle head can be adjusted 360&#...
XLT02Z Instruction Manual - Page 7
...will be reduced. 2. OPERATION
CAUTION: • Always insert the battery cartridge all the way until the red part cannot be seen. Turn the tool on and fasten for a longer period of the workpiece to the diameter ...fall out of the tool, causing injury to you or someone around you can see the red part on the hex end or square
end) will differ according to use of the universal joint or...
XLT02Z Instruction Manual - Page 8
... by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
It is warranted to be sure that the tool is switched off and the
battery cartridge is thoroughly inspected and tested before attempting to perform inspection or maintenance. • Never use of any trouble develop during this manual.
To maintain product SAFETY and RELIABILITY, repairs, any...
XLT02Z Parts Breakdown - Page 2
.... 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 1 0 1 PC. 1 PC. Model XLT02Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
187889-4
001 C10 263005-3
001 C20 803B00-9
001 C21 802J50-9
001 D10
002
265995-6
003
815L76-4...
424044-0
043
231990-8
HOUSING SET RUBBER PIN 6 CAUTION LABEL CAUTION LABEL INC. 40 TAPPING SCREW 4X18 XLT02 NAME PLATE TERMINAL RUBBER PIN ...
Makita XLT02 Reviews
We have not received any reviews for Makita yet.