Makita XPH03Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XPH03Z manuals!
Problems with Makita XPH03Z?
Ask a Question
Free Makita XPH03Z manuals!
Problems with Makita XPH03Z?
Ask a Question
Popular Makita XPH03Z Manual Pages
XPH03Z Instruction Manual - Page 2
...from heat, oil, sharp edges or moving parts. A moment of inattention while operating power ... is earthed or grounded.
6. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XPH03
Drilling into concrete
16 mm (5/8")
Drilling into steel...research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may ignite the ...
XPH03Z Instruction Manual - Page 3
... identical replacement parts. Keep cutting tools sharp and clean. in the hands of children and do the job better and safer at all times. Recharge only with these instructions to noise can reduce dust-related hazards. Under abusive conditions, liquid may cause burns or a fire. 27. If contact accidentally occurs, flush with specifically designated battery...
XPH03Z Instruction Manual - Page 4
... to follow the safety rules stated in a container with any conductive material. (2) Avoid storing battery cartridge in this
instruction manual may reach or exceed 50 ﾟ C (122 ﾟ F).
7. Do not store the tool and battery cartridge in a fire.
8.
Tips for tool. ･ volts
･ direct current
･ no one is completely worn out. The...
XPH03Z Instruction Manual - Page 5
... of the cartridge. Release the switch trigger to stop the application that caused the tool to the tool and battery cartridge and a personal injury. Installing or removing battery cartridge
1.
Star marking
012128
Lithium-ion batteries with a star marking are placed under one of the following conditions: • Overloaded:
The tool is too low and...
XPH03Z Instruction Manual - Page 6
...the ring. Selecting the action mode
1. When the reversing switch lever is set the ring correctly to the "2" side for high speed or, "1" side for your desired mode
mark. CAUTION... tool stops may damage the tool. • When not operating the tool, always set the speed change
1.
CAUTION: • Always set the reversing switch lever to the
correct position. CAUTION: • Always check the ...
XPH03Z Instruction Manual - Page 7
... the pointer, and maximum when the marking is shown in the following table.
Installing or removing driver bit or drill bit
1.
The status displayed on the switch panel and the remaining battery capacity is aligned with the pointer on the panel. Installing side grip (auxiliary handle)
2
1
3 4
5
1. Protrusion 3. Grip base 5. Then tighten the grip by...
XPH03Z Instruction Manual - Page 8
...set to do so may be resumed. Hook 3. Failure to desired position, then tighten the clamp screw. Light pressure gives best results. By repeating this operation. Installing bit holder
OPERATION
1. Bit holder 2. Bit 1
2
012708
Fit the bit holder into a groove in the concrete. When not using the driver...there. Do not force the tool. To install the hook, insert it with a screw....
XPH03Z Instruction Manual - Page 9
...driver bit is operated continuously until the battery...Replacing carbon brushes
1. Use only identical carbon brushes.
1
1. Screws
2
012705
Use a screwdriver to the marking. Arm
2. Hold the tool firmly and exert care when the bit begins to break through . Drilling in wood When drilling in the recessed part of the housing with a fresh battery...guide screw makes drilling easier by setting...
XPH03Z Instruction Manual - Page 10
...risk of the carbon brushes. EN0006-1
10 Reinstall the rear cover and tighten two screws securely. OPTIONAL ACCESSORIES
CAUTION: • These accessories or attachments are required because of Makita's Factory or Authorized Service Centers. It is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. If inspection shows the trouble is warranted to...
XPH03Z Parts Breakdown - Page 2
...BRUSH HOLDER COMPLETE CARBON BRUSH CB-440 (195021-6) RUBBER PIN 4 REAR COVER TAPPING SCREW BIND PT 3X16 TERMINAL SEAL SPONGE A PAN HEAD SCREW M3X10 SPONGE B HEAT SINK HOUSING SET... CHARGER BATTERY BL1840 SET BATTERY COVER PLASTIC CASE COMPLETE
1 1 PC...) 2 SET (XPH03M) 1 PC. (XPH03M) 1 PC. (XPH03M) Model XPH03M, XPH03Z Parts LIST
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
...
Makita XPH03Z Reviews
We have not received any reviews for Makita yet.