Makita XSC03Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XSC03Z manuals!
Problems with Makita XSC03Z?
Ask a Question
Free Makita XSC03Z manuals!
Problems with Makita XSC03Z?
Ask a Question
Popular Makita XSC03Z Manual Pages
XSC03Z Instruction Manual - Page 2
... safety warnings
WARNING: Read all instructions listed below may differ from heat, oil, sharp edges or moving parts.
Keep work area clean and well...BATTERYoperated (cordless) power tool.
Use of electric shock.
2. Electrical Safety
1. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XSC03
Blade diameter
136 mm (5-3/8″)
Max. Do not use a ground fault circuit ...
XSC03Z Instruction Manual - Page 3
... different from injury when using only identical replacement parts. avoid contact. Do not expose a ...instructions and do not wear cloth work to fire or excessive temperature. Never service damaged BATTERY packs. Maintain power tools and accessories. Damaged or modified batteries may be repaired...If contact accidentally occurs, flush with specifically designated BATTERY packs. Do not ...
XSC03Z Instruction Manual - Page 4
...the cutting depth to repair the appliance or the ...should be retracted manually only for any...the workpiece. Supports must be... fence or straight edge guide. Unsharpened or improperly set blades produce narrow kerf ... existing walls or other part, in line with a...operate automatically.
4. Follow instruction for optimum performance and safety...cutting tool may be serviced before each use damaged...
XSC03Z Instruction Manual - Page 5
...replace...supported, not on the section that will also void the Makita warranty for hazardous material is marked on that it is severely damaged or is extremely dangerous and can lead to serious accidents. 6. Use the batteries only with clear water and seek medical attention right away. Installing...INSTRUCTIONS. Do not disassemble battery cartridge.
3. It may result in this instruction manual...
XSC03Z Instruction Manual - Page 6
.... Overcharging shortens the battery service life.
3.
If not, it is placed under one of the following conditions. CAUTION: Do not install the battery cartridge forcibly. Overload...the batteries. Tips for a few seconds.
6 ENGLISH Charge the battery cartridge before installing or removing of the cartridge. FUNCTIONAL DESCRIPTION
CAUTION: Always be seen.
Overdischarge protection
...
XSC03Z Instruction Manual - Page 7
...
25% to 50%
0% to a Makita service center for dangerous KICKBACKS which can cause switch... releasing the switch trigger. Alignment line 2. Switch action
WARNING: Before installing the battery cartridge into the tool, always check to the "OFF"...lever is provided. For cleaner, safer cuts, set cut
CAUTION: After adjusting the depth of repair may differ slightly from being accidentally pulled, a...
XSC03Z Instruction Manual - Page 8
... dust of such materials can cause personal injury. The saw dust and the dust box with bare hands immediately after switch lever release, have tool serviced at a Makita service center. Periodically dump the saw dust in breakage which thinner, gasoline, grease, or other chemicals are applied.
Hex wrench
2
► 1 . Lever
1 8 ENGLISH Be careful...
XSC03Z Instruction Manual - Page 9
... Makita wrench to the operator. Slipping your job.
This may cause a poor cutting performance and/or present a risk of accumulated metal chips as discussed in the cut. Cup washer
To install ..., make sure to be careful not to install it on the spindle. CAUTION: Never twist or force the tool in the Maintenance section. Replace it flat and advancing smoothly until the circular...
XSC03Z Instruction Manual - Page 10
... SAFETY and RELIABILITY, repairs, any other maintenance or... dull circular saw blade is set to chips and particles being ...fence is securely installed in the base ... and possible serious injury. Rip fence (Guide rule) 2. Simply slide the rip fence...Makita Authorized or Factory Service Centers, always using compressed air to perform inspection or maintenance. When using Makita replacement parts...
XSC03Z Instruction Manual - Page 11
... local Makita Service Center. • Carbide-tipped circular saw blades • Rip fence (Guide rule) • Clamping screw • Hex wrench • Safety goggles • Makita genuine battery and charger
NOTE: Some items in the list may differ from country to the limit mark. If electric brake is not available, refer to this manual. Take...
XSC03 Parts Breakdown - Page 2
Model XSC03Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
266053-1
002
643807-7
003
... 4X18 BALL BEARING 696ZZ RETAINING RING S-10 HELICAL GEAR 23 SLEEVE 10 BEARING RETAINER 14-23 BALL BEARING 6900DDW O RING 26
Q'ty Unit
3 PC. 2 PC. 1 SET 1 SET 0 1 SET 0 4 PC. 1 PC. 1 PC. 1 PC. 8 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 3 PC. 1 PC. 1 PC. 1 ...
XSC03 Parts Breakdown - Page 3
... HEX.SOCKET HEX.BOLT M6X18 STOP RING E-8 LEVER 40 HEX. LABEL PLATE H.S.H.B M6X29 COMPRESSION SPRING 7 DUST CAP O RING 5 TAPPING SCREW 4X18 DUST BOX SET INC. 78 DUST BOX SET INC. 77 DUST BOX ASSEMBLY INC. 72-78 SAFETY GOGGLE HEX. WRENCH 5 TCT SAW BLADE 5-3/8"X5/8X30T
1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 PC...
XSC03Z New Tool Flyers English - Page 1
... over-heating
SPECIFICATIONS
Blade Diameter 5-3/8" Arbor 5/8" Max. The Makita Teal Color is...specifications subject to 2" in L.E.D. NTF-0918 MA-5192-18
4
5
makitatools.com Power Type Cordless UPC Code (XSC03T 088381-865692 UPC Code (XSC03Z 088381-865630
STANDARD EQUIPMENT
• XSC03Z... Charger (DC18RC) • 5-3/8" 30T C.T. All models and accessories subject to stock on the job •...
Makita XSC03Z Reviews
We have not received any reviews for Makita yet.