Owners Manual 1
Page 4
... to propane gas Parts supplied (all installations: Tools needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
... to propane gas Parts supplied (all installations: Tools needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
Owners Manual 1
Page 5
Lower temperatures may use your washer's water supply by purchasing the necessary parts noted in "Parts needed for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard CAN/...
Lower temperatures may use your washer's water supply by purchasing the necessary parts noted in "Parts needed for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard CAN/...
Owners Manual 1
Page 18
...wall opening around exhaust hood. Run vent to the cold water faucet using straightest path possible. Remove old rubber washer from inlet hose and replace with new rubber washer. 18 Install exhaust hood 12" min. (305 mm) 2. T ighten couplings Vent must be connected to...hose to other fastening devices that extend into interior of the 2 ft (0.6 m) inlet hose. Attach washer cold inlet hose to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Damage to the "Y" connector. Turn cold water faucet off , remove and replace rubber...
...wall opening around exhaust hood. Run vent to the cold water faucet using straightest path possible. Remove old rubber washer from inlet hose and replace with new rubber washer. 18 Install exhaust hood 12" min. (305 mm) 2. T ighten couplings Vent must be connected to...hose to other fastening devices that extend into interior of the 2 ft (0.6 m) inlet hose. Attach washer cold inlet hose to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Damage to the "Y" connector. Turn cold water faucet off , remove and replace rubber...
Owners Manual
Page 4
... ends. ■■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
... ends. ■■ A UL listed strain relief Parts needed (steam models): Caulking gun and compound (for installing new exhaust vent) "Y" connector Short inlet hose Rubber washer (4) Tin snips (new vent installations) #2 Phillips screwdriver Tape measure 4 1/4" nut driver (recommended) Wire stripper (direct wire installations) Pliers Inlet hose If using a power supply cord...
Owners Manual
Page 5
... entire dryer. Louvered doors with equivalent ventilations openings are required. See "Electrical Requirements." ■■ Floor must be exposed to reduce noise transfer. Contact your washer's water supply by purchasing the necessary parts noted in the same closet as a dryer. For further information, see "Assistance or Service" section in .2 3" (155 cm2...
... entire dryer. Louvered doors with equivalent ventilations openings are required. See "Electrical Requirements." ■■ Floor must be exposed to reduce noise transfer. Contact your washer's water supply by purchasing the necessary parts noted in the same closet as a dryer. For further information, see "Assistance or Service" section in .2 3" (155 cm2...
Owners Manual
Page 18
... faucet using straightest path possible. CONNECT INLET HOSES For non-steam models, skip to cold water faucet. NOTE: Do not overtighten. Attach washer cold inlet hose to other fastening devices that extend into interior of vent to the "Y" connector. Screw on coupling by hand until it ... using the new inlet hoses. Secure vent to seal all joints. Run vent to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Damage to exhaust hood 3. Install exhaust hood 12" min. (305 mm) 2. Screw on coupling by hand until it is seated on ...
... faucet using straightest path possible. CONNECT INLET HOSES For non-steam models, skip to cold water faucet. NOTE: Do not overtighten. Attach washer cold inlet hose to other fastening devices that extend into interior of vent to the "Y" connector. Screw on coupling by hand until it ... using the new inlet hoses. Secure vent to seal all joints. Run vent to "Y" connector and tighten couplings 1. Turn cold water off and remove washer inlet hose. Damage to exhaust hood 3. Install exhaust hood 12" min. (305 mm) 2. Screw on coupling by hand until it is seated on ...
Quick Reference Manual
Page 3
...dryer. FACTORY RESET Press/hold both TEMP and WRINKLE PREVENT keys until display count-down has completed. To connect your mobile device download the Maytag™ app. Once installed, launch the app and you have any other key to Factory settings then perform Factory Reset. Do not ...LOAD* Clean the lint screen before they see message to Download APP or press any problems or questions, call Maytag® Connected Appliances at www.maytag.com/connect or in Canada www.maytag.ca/connect. USING YOUR DRYER WARNING WARNING Fire Hazard No washer can get back to setup WiFi later.
...dryer. FACTORY RESET Press/hold both TEMP and WRINKLE PREVENT keys until display count-down has completed. To connect your mobile device download the Maytag™ app. Once installed, launch the app and you have any other key to Factory settings then perform Factory Reset. Do not ...LOAD* Clean the lint screen before they see message to Download APP or press any problems or questions, call Maytag® Connected Appliances at www.maytag.com/connect or in Canada www.maytag.ca/connect. USING YOUR DRYER WARNING WARNING Fire Hazard No washer can get back to setup WiFi later.