NEC MT1035 - MultiSync XGA LCD Projector Support and Manuals
Popular NEC MT1035 Manual Pages
User Manual - Page 1
NEC Multimedia Theatre
MultiSync® MT1035™
LCD Projector User's Manual
NEC Technologies
NEC Multimedia Theatre
NEC Technologies, Inc. 1250 N. Arlington Heights Road,Suite 500 Itasca, Illinois 60143-1248
Part No. 78409631 Printed in Japan
User Manual - Page 2
... harmful interference to radio communications. NO USER-SERVICEABLE PARTS INSIDE. Failure to the unit EXCEPT those specified by NEC Technologies in which case the user will be read this manual carefully before using your right to operate this government regulation could void your NEC MultiSync MT1035 LCD Projector and keep the manual handy for a Class A digital device, pursuant to...
User Manual - Page 3
... this happens, contact your LCD projector and to your projector. If installing the LCD projector on . The ceiling must be strong enough to support the LCD projector and the installation must be careful not to clean the lens, and be installed by a qualified NEC service person.
3. b. Power Supply
1. Ensure that vents are to use the lamp after every 100 hours of...
User Manual - Page 6
... the problem to your product, consult the dealer from an authorized NECTECH dealer. Costs of initial technical adjustments (set-up), including adjustment of the first customer purchase. Whenever warranty service is warranted for service MUST have other rights which vary from the date of user controls. L I M I T E D WA RRA NT Y
9
NEC MultiSync® LCD Projector Products
NEC...
User Manual - Page 8
...; Keystone correction allows you to correct trapezoidal distortion
so that comes with your projector and describes the features and controls.
C o n s u l t y o u r NEC dealer for your presentation.
*1 Installing the MultiSync MT1035 LCD Projector on the screen with the pointer and enlarge the selected area.
• Supports most IBM VGA, SVGA, XGA, SXGA(with SXGA (1280ן...
User Manual - Page 9
... Projector.
• NEC MultiSync MT1035 LCD Projector • Remote Control With Built-In Laser Pointer And Cables • Mouse Adapter for IBM PS/2 and Mac • Serial Cable • Signal Cable (15-Pin Mini D-Sub To 15-Pin Mini D-Sub Connector) • Pin Adapter for Macintosh • Power Cable • Two AA Batteries • Quick Connect Guide...
User Manual - Page 10
... Features
Lamp Cover Lamp Cover Set Screw
Remote Sensor
Connector Cap Carrying Handle
10
INTRODUCTION
S-VIDEO INPUT AUDIO
L/MONO
R
RGB MONITOR OUTPUT
AUDIO
PC CONTROL MOUSE OUTPUT REMOTE CONTROL
INPUT
L/MONO
R
VIDEO INPUT AUDIO
RGB INPUT 1
AUDIO
RGB INPUT 2
AUDIO
Filter Cover
Slot Cover for the Optional MT Viewer Board. 17
Getting To Know Your MultiSync MT1035 LCD Projector...
User Manual - Page 13
... the MultiSync MT1035 Projector. This enables you connect a second RGB audio output from the NEC MultiSync MT1035 remote control....remote sensors on the LCD projector cabinet will receive your mouse commands.
8 Remote Control Jack Connect your own program, command references are writing your remote control cable here for wired operation.
9 Built-in Security Slot ( )
This security slot supports...
User Manual - Page 21
... to moisture, dust, or smoke. Ceiling Installation
Installing your MultiSync MT1035 LCD Projector on the ceiling must be used at temperatures between the projector bottom and the top of
the projector. NOTE : Distances may vary ± 5%. The projector must be injured and the projector severely damaged. • Do not use your NEC dealer for more information. This will harm the...
User Manual - Page 25
... the MT1035, set to 1024ן768 unless "mirroring" is off the power to your Macintosh. Refer to owner's manual supplied with your new graphics board for installation instructions.
47
3.
Make sure that comes with your XGA/SVGA/VGA configuration. If your PC does not support XGA/SVGA/VGA you 've connected to the projector...
User Manual - Page 34
...in the under scan mode) if:
* the LCD projector fails to determine automatically. * you want to fine...or to project an image using NEC's AccuBlend Intelligent Pixel Blending Technology...
66
Usually set "Horizontal Position", "Vertical Position", "Picture Adjustment", "Fine Picture" and "Resolution" manually. When the... the Auto mode is evident when part of your computer for each color ...
User Manual - Page 37
... must first install the optional MT Viewer board (VK-MT) in the original position.
5. Remove the slot cover by pushing up on end with the two screws that you removed in step 2.
37
72 Put the LCD projector back in the LCD projector and set up .
Set the LCD projector on the catch of the cover with a flat...
User Manual - Page 41
... set screw and two lamp case screws. CAUTION: Do not use , the lamp bulb may cause injury. The filter comes in the lamp case.
Allow at 2000 hours to cool.
• The projector will be sure to prevent the risk of glass may shatter, and pieces of use a lamp other than the NEC replacement lamp. If this happens, contact your projector's model...
User Manual - Page 45
... cycle of operation and should be replaced. 5 TROUBLESHOOTING
87
This section helps you resolve problems you 're presenting is particularly warm, move the projector to a cooler location. • Check the filter and clean it if necessary. • If the problem persists, contact your NEC dealer for service.
Contact your MultiSync MT1035 LCD Projector.
Check each and reattach them if...
User Manual - Page 46
... 23 feet (7m) of the projector. To Contact Your NEC Service Representative, Call 1-800-836-0655
46
TROUBLE SHOOTING
90
89
Common Problems & Solutions
Problem
Check These Items
Does not turn on
No picture
Image isn't square to the screen Picture is blurred
Image is scrolling vertically, horizontally or both Remote control does not work
Status indicator...
NEC MT1035 Reviews
Do you have an experience with the NEC MT1035 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!