NEC P484 Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC P484 Manual Pages
Users Manual - Page 1
Large Format Display
User's Manual
MultiSync P404 MultiSync V404 MultiSync P484 MultiSync V484 MultiSync P554 MultiSync V554
Please find your model name in the label on the backside of monitor.
Users Manual - Page 24
... cable
Under 29 mm
NOTE: It is 300.
Refer to the Windows® instruction user's manual or Help file on the remote control, or "AUTO" in a folder including folder icons is not guaranteed to the monitor.
PAGE UP PAGE DOWN SETTINGS
Displays a list of files can be displayed. NOTE:
The maximum number...
Users Manual - Page 48
When manually specify the ID number or control by using RS-232C, REMOTE IN or LAN daisy-chain connection. Main Monitor
Connector
IN
OUT
RS-232C
REMOTE IN
LAN2
LAN1
Sub Monitors
Connector
IN
OUT
LAN1
LAN2
Connection
MultiSync
MultiSync
LAN1 LAN2 LAN Cable
LAN1 LAN2 LAN Cable
MultiSync
English-46
NOTE:
Multiple monitors that are daisy-chained...
Users Manual - Page 56
... function is only for PJLink. Set a password for HTTP server. A password must be 10 characters or less. This standard protocol is only for class1 and class2 command. Only the master monitor can be used .
TITLE MESSAGE MEMO PASSWORD MEMO PASSWORD ENABLE
A title must be 16 characters or less. The default is model name. External Control
Connecting external...
Users Manual - Page 58
... RECIEVER then press SET/POINT ZOOM.
In addition, this monitor to HDMI. If the monitor is turned standby while a HDMI CEC supporting device is recording, the device is necessary that the connected HDMI CEC supporting device to the monitor will also be switched. Please refer to the user's manual supplied with the monitor, HDMI CEC supporting devices also go...
External Control Codes - Page 11
... Lo Hi Lo Hi Lo MSB
LSB MSB
LSB
Refer to section 5.2 "Get parameter reply" for more details.
3)Set parameter
The controller sends this message to change a setting of the monitor.
Operation code table". Refer to the section 4.1 "Header block format" for more detail.
1)Get current parameter
The controller sends this message when...
External Control Codes - Page 23
...0Dh): End of Message '0'-'0' (30h, 30h): Result code. Monitor ID: Indicate a replying Monitor ID. Message STX (02h): Start of packet
Step 2. The monitor replies with the current brightness setting and
capability to support this operation. (Get parameter)
Header SOH-'0'-Monitor ID-
'0'-'C'-'0'-'6'
Message STX-'0'-'0'-'1'-'0'-ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of...
External Control Codes - Page 24
... length is the controller.
Header
Message
SOH-'0'-'0'- Monitor ID: Indicate a replying Monitor ID.
Delimiter CR (0Dh): End of Message '0'-'0' (30h, 30h): Result code. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Set Backlight setting 80(0050h). Ex.) When this byte is...
External Control Codes - Page 26
MultiSync P404/ P484/ P554/ V404/ V484/ V554 have three built-in temperature sensors.
The monitor replies for reading the temperatures from the sensors. Monitor ID: Indicates a replying Monitor ID. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 78h (in the page 2). '0'-'0' (30h, 30h): This operation is "Set parameter" type. ...
External Control Codes - Page 27
... you want to the section 4.3 "Check code" for a BCC calculation. The monitor replies a temperature of packet
Step 4. Ex.) When this byte is set to send the temperature from the selected sensor.
Message STX (02h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is 6 bytes.
No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h...
External Control Codes - Page 47
...Delimiter CR (0Dh): End of Message '0'-'0' (30h, 30h): Result code. Header SOH-'0'-Monitor ID-
'0'-'A'-'0'-'C'
Message STX-'C'-'2'-'0'-'3'-'D'-'6'-
'0'-'0'-'0'-'1'-ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of Message
(47/135) 7.2 Power control
1) The controller requests the monitor to change a setting. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the...
External Control Codes - Page 50
...of packet
(50/135)
ETX (03h): End of Message
Check code
BCC: Block Check Code Refer to the monitor at a time is 32bytes. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write ...4.3 "Check code" for confirmation. N-N: Message length Note.) The maximum data length that can be written to the monitor at a time is 32bytes.
Ex.) When this byte is set to write Asset...
External Control Codes - Page 94
...". '0'-'A'(30h,41h): Message length (10byte)
Message
STX (02h): Start of Message 'C'-'B'-'0'-'9' (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of packet
2) The monitor replies to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of Message
Check...
Raspberry Pi Compute Module Setup Guide - Page 33
... /etc/init.d/lirc stop mode2 -d /dev/lirc0
©2017 NEC Display Solutions, Ltd. Notes:
• A reboot is usually necessary to ENABLE. If not set to enable support. • If lirc support is not included with the OS, it can be installed using : sudo apt-get install lirc
• Additional configuration may be required in the OS...
Raspberry Pi Compute Module Setup Guide - Page 43
... between the Compute Module, Internal PC (OPS) (if installed), and an External PC connected to the Compute Module. It also routes the internal USB connection from the touch sensor will automatically switch to the correct source device.
©2017 NEC Display Solutions, Ltd. This setting can be configured to the display for communications...
NEC P484 Reviews
We have not received any reviews for NEC yet.