NaceCare AV12QX Support and Manuals
Get Help and Manuals for this NaceCare item
View All Support Options Below
Free NaceCare AV12QX manuals!
Problems with NaceCare AV12QX?
Ask a Question
Free NaceCare AV12QX manuals!
Problems with NaceCare AV12QX?
Ask a Question
Most Recent NaceCare AV12QX Questions
How Can I Get The Pre Spray Solution When Using The Wand?
How can I get the pre spray solution when I have the wand hooked up? All I can get from the wand is ...
How can I get the pre spray solution when I have the wand hooked up? All I can get from the wand is ...
(Posted by katrinacrane 8 years ago)
Popular NaceCare AV12QX Manual Pages
AV12QX Owners Manual - Page 1
NaceCare Solutions 1205 Britannia Road East Mississauga, Ontario, Canada
L4W 1C7 Toll Free: 1 800 387 3210 Toll Free Fax: 1 800 709 2896 Owners Manual for the AV12QX
PRIOR TO USING THIS MACHINE, MAKE SURE THAT YOU HAVE READ, AND UNDERSTAND THE SAFETY AND OPERATING INSTRUCTIONS FOR THIS MACHINE.
AV12QX Owners Manual - Page 2
... injury to the operator (shock, electrocution, etc.). Safety instructions (read the following safety instructions carefully and ensure that you understand them . •... you are using produces foam, or if you are cleaning carpet previously treated with
shampoo, you must add defoamer into the ...not repair the cable in case of tears, but replace it is
watertight. • Take care of the...
AV12QX Owners Manual - Page 3
... hose and floor wand (see Using with cold or warm water, through the filling hole, adding chemical according to the manufacturer's specifications. SETUP This machine is designed to clean large areas of carpet (see Safety Regulations).
3 Plug the power cord into the wall outlet (see Using as a Self-propelled Machine). For normal operation...
AV12QX Owners Manual - Page 4
...the circuit breaker trips, reduce the brush pressure on carpet as a Self-contained Extractor
Water-flow adjustment knob
Vacuum shoe pressure adjustment
Brush ...problem persists, contact the nearest service center.
3. This machine is located on hard floor, lower the brush all the way to a scrubber/dryer with an optional hard floor squeegee (P/N#18270E).
2. For carpet, the recommended setting...
AV12QX Owners Manual - Page 5
...hose, which connects the solution tank to the hand-tool using the solution and the vacuum hoses. Set the pump switch to the "I " position, the pump will only work when the
solution control...
VACUUM BRUSH
SOLUTION CONTROL
4. In the "I " position.
On the lower left side of the paragraph SETUP), you can adjust the water flow by turning the ball
valve knob. Connect the machine to the wand...
AV12QX Owners Manual - Page 6
Switch on . 6. Connect the longer vacuum hose to the machine 4. In this position, the solution pump is always on the vacuum motor by setting the switch to the "I" position. 5. Solution hose
Vacuum hose
2. Connect the longer solution hose to the machine 3. To spray water you need to the "II" ...
AV12QX Owners Manual - Page 7
...fan casing. 4. Remove any hair or carpet fibres that the machine is located below the recovery dome. 6. After 500 working hours, the machine should be serviced. AFTER USE, FOLLOW THESE STEPS 1. ...Clean the recovery dome and gasket. 2. When storing the machine, make sure that have built up on
the vacuum motor and pump motor should be replaced...
HT1800 Heater Owners Manual - Page 2
... the solution tank to trip if used on the same power supply (For 15A and 20A services). Using the same power supply will still be used by the cable • Do not handle....). If an extension cord must be replaced with wet hands. • Do not spray water near the outlets. Safety instructions (read the following points and be used on a different power supply to the carpet extractor.
HT1800 Heater Owners Manual - Page 3
...is also provided with the 2 6mm lock nuts. This hose can be used to replace the solution hose of the control panel cover. Mount the 2 metal
brackets on the ...parts, necessary to fix the heater on a Santoemma machine:
• 2 metal brackets, to mount the heater on the machines with model# TP8X, TP12QX, and TP18SX/DX.
• 1 metal bracket, to mount the heater on the machines with model AV12QX...
HT1800 Heater Owners Manual - Page 5
Mounting for models AV12QX, and AV18AX To mount the heater to the 2 metal brackets, vertically, as indicated in the picture. Mount the 2 metal brackets on the bracket by using the 2 x 6mm lock nuts.
5 Mount the heater to the AV12QX, or AV18AX, Follow these instructions: 1. Lock the heater using the 2
screws (M4x20) provided. 2. Hang the heater...
HT1800 Heater Owners Manual - Page 6
...water inside the heater has become hotter than 30-40 seconds. The heating element and other parts
are illuminated. Switch the heater on again, indicating that the solution is connected to the ... the carpet extractor. 7. Insert the plug of the thermal protectors are very hot and can cause severe burns. • Do not try to service the heater yourself. • Repairs may be...
HT1800 Heater Owners Manual - Page 8
...-circulate the water and deliming chemical in the solution for this process 4. Add 1 quart of a deliming chemical into the solution tank. 2. NaceCare Solutions 1205 Britannia Road East Mississauga, Ontario, Canada
L4W 1C7 Toll Free: 1 800 387 3210 Toll Free Fax: 1 800 709 2896
8... time, you will develop a build up of lime and calcium inside of the heating coil, follow these instructions:
1.
Smart Kit Installation Manual - Page 3
Using rivet gun install rivet and make sure rivet grabs washer tightly against the tank. Remove two screws (top right and bottom right) from coming loose**
3
Attach chemical mounting ...
Smart Kit Installation Manual - Page 4
Tighten grey bracket facing away from machine. Mounting bracket and Hose holder installed on top left hand side of machine
4 bolt 5.
Flat washer 4. Three screws 3. Bracket hardware securely fastened to top left hand side of the tank. Grey ...
NaceCare AV12QX Reviews
We have not received any reviews for NaceCare yet.