NaceCare AV12QX Support Question
NaceCare AV12QX Support Question
Find answers below for this question about NaceCare AV12QX.Need a NaceCare AV12QX manual? We have 3 online manuals for this item!
Question posted by katrinacrane on August 17th, 2015
How Can I Get The Pre Spray Solution When Using The Wand?
How can I get the pre spray solution when I have the wand hooked up? All I can get from the wand is water.
Current Answers
Answer #1: Posted by TechSupport101 on August 17th, 2015 9:35 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Please see the manual here https://www.helpowl.com/manuals/NaceCare/AV12QX/240581 for the best walk through.
Related NaceCare AV12QX Manual Pages
AV12QX Owners Manual - Page 1
NaceCare Solutions 1205 Britannia Road East Mississauga, Ontario, Canada
L4W 1C7 Toll Free: 1 800 387 3210 Toll Free Fax: 1 800 709 2896 Owners Manual for the AV12QX
PRIOR TO USING THIS MACHINE, MAKE SURE THAT YOU HAVE READ, AND UNDERSTAND THE SAFETY AND OPERATING INSTRUCTIONS FOR THIS MACHINE.
AV12QX Owners Manual - Page 2
... children and people unable to prevent water from being sucked through the vacuum motor. • If the chemical you are using , store the machine, well cleaned, in an explosive atmosphere. • Do not let the machine be performed by qualified personal only!
2 Do not use the machine to spray or to suck dust,
corrosive...
AV12QX Owners Manual - Page 3
Fill in the lower tank (solution tank) with cold water only! 2.
Attention: wool carpet must be used to clean small areas of carpet, with an additional hose and floor wand (see Using with Accessories) The following steps explain how to prepare the machine for use:
1. Plug the power cord into the wall outlet (see Using as a Self-propelled...
AV12QX Owners Manual - Page 4
...center.
3. If using the machine, you are finished using on the top ...control panel. NOTE: For hard floor cleaning, a more aggressive brush is the second last notch. This machine is located on the lower right side of being converted to transport the machine. If the circuit breaker trips, reduce the brush pressure on carpet as a Self-contained Extractor
Water...
AV12QX Owners Manual - Page 5
Turning the knob counter clockwise increases the water flow. Set the pump switch to the hand-tool using the solution and the vacuum hoses. Turning the knob clockwise reduces the water flow. In the "I
PUMP
VACUUM BRUSH
SOLUTION CONTROL
4. Connect the machine to the wand or to the "I " position. 5.
To connect the hoses to the machine, remove...
AV12QX Owners Manual - Page 6
... to the "II" position. Turn the pump to the "I" position. 5. In this position, the solution pump is always on the handle of the floor wand or hand tool.
6 Connect the longer solution hose to pull the lever situated on . 6. To spray water you need to the machine 4. Connect the longer vacuum hose to the machine...
AV12QX Owners Manual - Page 7
... in the solution tank and pump this procedure, make sure to prevent odors from the motor
fans and fan casing. 4. AFTER USE, FOLLOW THESE STEPS 1. Put some fresh water in damage ...This will
allow any moisture from developing. 3. It is unplugged. Periodically clean the water filter located inside the solution tank. 7. Periodically remove and clean the brush. For this through the system....
HT1800 Heater Owners Manual - Page 2
...; Do not let the device to be used on pre-heating the water. Also, do not pull the plug out of the wall by children and persons unable to understand the danger connected
with wet hands. • Do not spray water near the outlets. Pre-heat the water in the solution tank to the desired temperature
2. Refill the...
HT1800 Heater Owners Manual - Page 3
... on the machines with model AV12QX, and AV18AX. • 2 6mm lock nuts, to mount the metal brackets to the heater. • 4 screws (M4 x 20mm), used to mount the brackets to re-circulate hot water into the holes of the 2 metal brackets, and tightening them with a solution hose capable of using the 4 screws M4x20 provided in...
HT1800 Heater Owners Manual - Page 5
... in the picture, by inserting the screws coming out of the rear side of the heater into the holes of the brackets. Lock the heater using the 2
screws (M4x20) provided. 2. Mounting for models AV12QX, and AV18AX To mount the heater to the 2 metal brackets, vertically, as indicated in the picture.
HT1800 Heater Owners Manual - Page 6
... 2 reasons:
1. Switch the heater on as indicated above. 2.
Once you release the spray trigger for
the 2 thermal protectors will be made by using the solution hose provided. 5. The green light is connected to the cleaning accessory, by qualified personnel only!
6 The water inside the heater has become hotter than 30-40 seconds, you should...
HT1800 Heater Owners Manual - Page 7
... minutes you re-circulate the water for 10 minutes before use, the water in the solution tank. Switch the water pump and the heater on. Let the water re-circulate in your solution tank will pre-heat the water and discharge it ).
2. Insert the end of the solution hose into the solution tank of
water increasing in the solution tank becomes warm. Example...
HT1800 Heater Owners Manual - Page 8
... water into the solution tank. 3. Empty the solution tank and refill with the lime. (Use the same process as pre-heating the water in the solution for this process 4.
To clean the inside the heating coil which will clean out the pump, water lines and heating coil. This will greatly reduce the efficiency of the heater. Spray the clean water...
Smart Kit Installation Manual - Page 2
Pre-spray Hose 3. Chemical dispensing system 4. Hose holder 7. Electric or Cordless Drill* 5. 5mm Allen Wrench 6. 1/8" Drill Bit*
* = If your machine does not have the bracket shown in the next picture. One bracket 2. Rivet gun* 2. 10mm Socket or Wrench 3. Two Rivets 3. Two Washers
Required: Chemical Dispensing system and the Chemical box bracket. Long shank Philips...
Smart Kit Installation Manual - Page 3
... install rivet and make sure rivet grabs washer tightly against the tank. Hold washer on inside of top tank, use mounting bracket as shown. With rivets and washers provided, insert rivet into bracket/tank.
Attach chemical mounting bracket as shown with longer screws and washers provided with kit hardware
**IF NEEDED On left side of...
Smart Kit Installation Manual - Page 4
... holder Place threaded washer inside grey holder as shown
Grey bracket holder mounted using three Philips screws provided. Tighten grey bracket facing away from machine. Bracket 2. Three screws 3.
Bracket hardware securely fastened to top left hand side of the ...
Smart Kit Installation Manual - Page 5
Using pre-spray mode: 1. Jets provided with the spray bar: For restorative cleaning turn the valve to the position. For 3 jet wand, low moisture 1 yellow - For plastic hand tool, low moisture
5 For Maintenance cleaning turn the valve to the left.
Begin pre-spraying and adjust spray pattern as shown to the position. With hose holder and 10mm bolt provided...
Similar Questions
Wont Spray
i cannot get spray to come out of machine. I have cleaned the spray tip.
i cannot get spray to come out of machine. I have cleaned the spray tip.
(Posted by vzopfsummit 2 years ago)
Machine Quits Alot
My TTB 1620 machine will constantly quits while it is being used. I turn the machine off and back on...
My TTB 1620 machine will constantly quits while it is being used. I turn the machine off and back on...
(Posted by dwbelding 7 years ago)
Pressure Issue With Rm1800h
The hose attachment for my RM1800H doesn't generate a lot of pressure when I use it, and the stream ...
The hose attachment for my RM1800H doesn't generate a lot of pressure when I use it, and the stream ...
(Posted by williamhodge 8 years ago)
Are There After Market Warranties Available For My Nacecare Pressure Washer?
I lost the original warranty registration card for my NaceCare pressure washer. How do I find out if...
I lost the original warranty registration card for my NaceCare pressure washer. How do I find out if...
(Posted by Anonymous-152116 13 years ago)