NaceCare TGB1120 Support and Manuals
Get Help and Manuals for this NaceCare item
View All Support Options Below
Free NaceCare TGB1120 manuals!
Problems with NaceCare TGB1120?
Ask a Question
Free NaceCare TGB1120 manuals!
Problems with NaceCare TGB1120?
Ask a Question
Popular NaceCare TGB1120 Manual Pages
Owners Instructions - Page 1
HGB 817/HGB 3045 TGB 817/TGB 3045 TGB 4045 TGB 4055
TGB 4055T
SCRUBBER DRYER
Owner Instructions
Warning! Read instructions before using the machine www.numatic.co.uk
Owners Instructions - Page 2
... Overview Page 4
Machine Set up Guide Page 5
Fitting Fuses / Isolator Key Page 5
Fitting the Brush / Pad Page 6
Fitting the Floor Tool Page 6
Fitting the Hose Guide Page 7
Filling the ...Specifications
Page 17
Rating Label / Personal Protective Equipment /
Recycling
Page 18
Safety Precautions Page 19-20
Schematic Diagram
Page 20
Recommended Spare Parts Page 21
Trouble...
Owners Instructions - Page 5
... in start-up Guide
! " Ensure ...20 Amp Fuse ● 1 x 2.5 Amp Fuse ● Maxi Fuse-puller
● Traction Model 2 x 50 Amp Fuse For Charger-less Model, all the above plus:
● 1 x Charger Connector ● 2 x Charger Connector ...Isolator Key (Fig.
"
!
Fuse Location
1
2
3
!
Machine Set-up pack) into contact with battery terminals while the batteries are exposed. ...
Owners Instructions - Page 6
... used brushes.
ensure a tight fit.
For fitting the floor tool blades (See Page 12).
6
www.numatic.co.uk Machine Set-up Guide
! Safety gloves are recommended for quick fitting, allowing easy squeegee blade replacement and a safety knock-off feature if the floor tool gets snagged, whilst in place.
Fit the floor tool and...
Owners Instructions - Page 7
...guide lines.
The clear dump hose at the rear of the machine can also be used for any reason always ensure it is refitted correctly before you need to health and safety instructions online. Control of Substances Hazardous to the manufacturers specification... (Fig.D). Machine Set-up Guide
Fitting the Hose Guide
The vacuum hose has a U-bend clip which creates a U-bend in the...
Owners Instructions - Page 8
IMPORTANT Do not operate machine unless the Operator Manual has been read and fully understood.
! Before performing the cleaning operation, place out appropriate warning signs and sweep or dust-mop the floor.
8
www.numatic.co.uk Machine Set-up Guide
A
B
Handle Height Adjustment
Using the handle position lever, lower the handle to the cleaning...
Owners Instructions - Page 9
... deck (Fig.B & C). Move the floor tool lever to suit the cleaning conditions. A
B
C
Setting the Cleaning Controls
To start: hold the deck up. Raising/Lowering the Floor Tool
After preparing the floor... (see previous section), we are now ready to set the controls to its lower position.
Before any settings can be applied, ensure the brush deck is lowered. Press in...
Owners Instructions - Page 10
... to safely disengage from its holder. Machine Operation
Break-away Floor Tool
The floor tool design incorporates a break-away feature. Machine In Use
To operate, set water flow rate tap, lower brush deck, lower the floor tool, press the vacuum / water switches, pull brush On/Off trigger. On heavily soiled floors...
Owners Instructions - Page 12
... www.numatic.co.uk Simply start by removing the four retaining pins, turn the floor tool over and separate the blade carrier from the body. Replacement is easy. Changing the Floor Tool Blades
! Blade carrier
3
4. Floor tool main body
4
5
NOTE: The blades are designed to any maintenance.
! Always ensure that the...
Owners Instructions - Page 17
... 67 dB(A) HAV ≤1.0 m/s²
2%
BRUSH WEIGHT BRUSH PRESSURE PAD PRESSURE CLEANING AREA BRUSH MOTOR POWER BRUSH SPEED BRUSH DIA PAD DIA VAC MOTOR MAX. Specifications
BRUSH WEIGHT BRUSH PRESSURE PAD PRESSURE CLEANING AREA BRUSH MOTOR POWER BRUSH SPEED BRUSH DIA PAD DIA VAC MOTOR MAX. with liquid)
TGB4045 - 17-33g...
Owners Instructions - Page 19
... power cord with the appliance or those specified in good condition.
• Replace any inexperienced repairs. When detergents or other persons who may impair safety.
Read the instruction manual before further use brushes provided with the correct Numatic approved replacement parts.
• Ensure that the work area is clear of obstructions and / or people.
• Ensure...
Owners Instructions - Page 20
... 4 hours after the green light has come on , at any worn or damaged parts and replace immediately. MainTtewniannTceec
Batteries Always re-charge the batteries after every use . Charge for a... Diagram
HGB3045 / TGB3045
TGB4045 & TGB4055
20 www.numatic.co.uk ORIGINAL INSTRUCTIONS READ MANUAL BEFORE USE
Information for Scrubber Dryer
Precautions when working with clean water and clean...
Owners Instructions - Page 21
... clogged Water flow not on Brush deck raised Too much load on the brush system
Trouble Shooting
SOLUTION
Fit or replace fuse (page 5) Charge batteries (page 13 / 14) Take off charge (page ... Castor Assembly Set Squeegee 650 Blade Set Complete 650 Squeegee Assembly Squeegee 750 Blade Set Complete 750 Squeegee Assembly Detent Pin
FILTERS
Spare Parts
Part No. 903341 903341 900903 Part No. 221091...
Owners Instructions - Page 24
Sihlbruggstrasse 142, 6340 Baar. Specification subject to change without prior notice www.numatic.co.uk © Numatic International Limited
904581 02/17 (A04) SCHWEIZ Tel: 0041 (0) 41 76 80 76 - 0 ...
TGB 1120 Pad Assist Walk Behind Scrubber Product Spec Sheet - Page 1
... and recovery tanks, the TGB 1120 is powered by 2 maintenance-free gel batteries • Features a patented flip-up to use anyone can be charged anywhere
MODEL
Cleaning Path Pad or Brush Size Solution/Recovery Tank Brush Pressure Brush Speed Brush Motor Vacuum Motor Power
TGB 1120
20" 20" 11 gal. 75...
NaceCare TGB1120 Reviews
We have not received any reviews for NaceCare yet.