NaceCare TGB516 Support and Manuals
Get Help and Manuals for this NaceCare item
This item is in your list!
View All Support Options Below
Free NaceCare TGB516 manuals!
Problems with NaceCare TGB516?
Ask a Question
Free NaceCare TGB516 manuals!
Problems with NaceCare TGB516?
Ask a Question
Popular NaceCare TGB516 Manual Pages
tgb_516_owner_manual.pdf - Page 1
Read instructions before using the machine www.numatic.co.uk TGB 516
SCRUBBER DRYER
Owner Instructions
Warning!
tgb_516_owner_manual.pdf - Page 2
SCRUBBER DRYER
TGB 516
Machine Overview
Pages 2
Control Panel Overview Page 3
Quick Set up Guide Page 4
Machine Set up Guide Page 5
Fitting the Brush / Pad Page 5
Fitting the Floor Tool Page 5
Filling the Clean Water Tank Page 6
Fill Level Indicator
Page 6
Water Flow Adjustment Page 6
Setting the Cleaning Controls Page 7
Raising/Lowering Floor Tool Page 8
Emptying Top/...
tgb_516_owner_manual.pdf - Page 5
... OPERATION AFTER THE REMOVAL OF ALL THE PACKAGING, CAREFULLY OPEN AND CHECK THE CONTENTS.
!
Ensure the battery has been charged before use. Quick Set-up Guide
! TTB1840G CONTENTS
1
2
● Owner Manual ● Battery Charger & Lead ● Battery Pack ● Scrub Brush
● Squeegee Assembly
Using the handle position lever, (Fig.1) move the handle...
tgb_516_owner_manual.pdf - Page 6
... on the brush.
Safety gloves are recommended for quick fitting, allowing easy squeegee blade replacement and a safety knock-off feature if the floor tool gets snagged, whilst in place.
Do not over tighten the retaining knobs. Machine Set-up Guide
! Ensure inspection cap is fitted first.
1
2
3
Swing the floor-tool carrier to the...
tgb_516_owner_manual.pdf - Page 7
...Set-up Guide
Filling the Clean Water Tank
The TGB 516 is equipped with a large 18 litre clean-water tank allowing large areas to be cleaned in a single fill.
If using a hose, bucket or a suitable container (Fig.2). Fill Level Indicator
The TGB 516...-water tank, remove the filler cap (Fig.1).
Ideally set the tap to 450 this enables the cleaning solution to enter the clean water tank during...
tgb_516_owner_manual.pdf - Page 8
...60 seconds.
The start : hold down either Trigger and press the On / Off
C
Switch once (Fig.A). Ideally set the tap to last the same time as a fully-charged battery.
E
The On / Off Switch and triggers ...pump will operate in this mode off and return to reset.
! Setting the cleaning controls
A
B 450
To activate the control panel: press the
Mode select button or press a trigger (...
tgb_516_owner_manual.pdf - Page 9
... yellow cap (ensure the sealing bung is then retrieved by hand. (fig.B).
!
IMPORTANT Do not operate machine unless the Operator Manual has been
read and fully understood.
! Machine In Use
To operate, set water flow rate tap, lower the floor tool, press the vacuum / water switches, pull brush On/Off trigger. WHEN...
tgb_516_owner_manual.pdf - Page 10
... the yellow cap fitted to the left hand side of the filter first then clipping the front to disconnect the separator from the machine (Fig.1 & 2). Replace by hand. (fig.B). Regular Maintenance
!
tgb_516_owner_manual.pdf - Page 11
... blades using the two outer knobs.
Floor Tool Overview
1. Refitting the Floor Tool Blades
Refit the blade holder, retain using (903531) replacement blade set (Fig.3), fitting the blades on to be reversible, thus extending their useful
working life. Note: The blades are designed to the moulded location lugs. Refit ...
tgb_516_owner_manual.pdf - Page 12
... to discharge to the point that you start using the red connection handle (Fig.A & B). The TGB 516 come with a 40 amp safety fuse.
i.e. If the machine will go out from battery. Connect ... the power supply and the charger lead from top to reset. Replace the fuse using (208526) Numatic approved part
Battery Charging
Recharge the machine fully after each use regardless of 30...
tgb_516_owner_manual.pdf - Page 13
...Specifications
Gross Weight (Full)
70 Kg Cleaning Speed
0 - 4.2 KPH
Brush Speed
Hi - 150 Rpm Lo - 130 RPM
Brush Pressure
27.4 g/cm2
Pad Pressure
26.2 g/cm2
Dimensions
Width = 520 mm Length = 850 mm Height = 1132 mm
Hand Arm Vibration
0.6 m/s2
Recharge Time 6 hrs
Trouble Shooting
PROBLEM... flow setting To much load on the brush system
Blown fuse in Battery pack
SOLUTION
Fit or replace fuse ...
tgb_516_owner_manual.pdf - Page 15
... must be secured against unintentional movement. When cleaning, servicing or maintaining the machine, replacing parts or converting to another function the power source shall be adequately instructed as cracking or ageing.
Use a respiratory mask in the instruction manual. When ordering spare parts always quote the Model Number / Serial Number specified on slopes exceeding...
tgb_516_owner_manual.pdf - Page 16
ORIGINAL INSTRUCTIONS READ MANUAL BEFORE USE
Information for wear and wipe clean. Always wear protective clothing e.g. Remove ... Dryer
Precautions when working with batteries. 2. Never rest tools or metallic objects on , at any worn or damaged parts and replace immediately. To remove the batteries:- Disconnect machine from the mains supply. 6. Always re-charge the batteries after use...
tgb_516_owner_manual.pdf - Page 17
...
CHARGER PACK (UK) CHARGER PACK (EURO) CHARGER PACK (SWISS) CHARGER PACK (USA) CHARGER PACK (SOUTH AFRICA) CHARGER PACK (AUS)
Spare Parts
Part No. 903531 903532 303985 903544 237232
SPARES & ACCESSORIES SERILOR REPLACEMENT BLADE SET SERILOR COMPLETE SQUEEGEE ASSEMBLY FILLER CAP ASSEMBLY FILLER CAP LID SEPERATOR FILTER
237260 GRIT BASKET
231054
213055 208471 303997 208448...
tgb_516_owner_manual.pdf - Page 20
... Charging Lead & Battery Pack
Fuse Pack Signed
Distributed by:
Numatic International Limited. SCHWEIZ Tel: 0041 (0) 41 76 80 76 - 0 www.numatic.ch
Numatic International ULDA. Specification subject to change without prior notice www.numatic.co.uk © Numatic International Limited
233968 03/17 (A30) Fränkische Straße 15-19...
NaceCare TGB516 Reviews
Do you have an experience with the NaceCare TGB516 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NaceCare yet.
Earn 750 points for your review!