Nady WHM-16 Support and Manuals
Get Help and Manuals for this Nady item
Popular Nady WHM-16 Manual Pages
Manual - Page 1
Instructions for use with any of these transmitters MGT-16 SYSTEM MHT-16 SYSTEM LINK-16 SYSTEM WHM-16 SYSTEM
MH-16 MT-16A
MT-16R
LK-16
WH-16
Manual - Page 2
...system you have about the operation and servicing of your system.
2 Contents
Introduction 2 Using this Manual 2 System Features (MGT-16/MHT-16/LINK-16/WHM-16 3 Quick User Controls/Connections Guide 4
MGT-16 Wireless Instrument Receiver 4 MT-16A/R Instrument Transmitter 6 MH-16 Horn Instrument Transmitter 7 LK-16 Snap-On Transmitter 8 WH-16 Head-Worn Transmitter 9 System Operation 10 MGT...
Manual - Page 3
... sync with receiver for mounting transmitter on -the-horn barrel style without any hardwired dynamic microphone • Up to selected receiver frequency for quick, easy setup
MGT-16 Instrument Receiver
• Compact, portable, "pedal style" receiver can be placed anywhere • Dual ¼ wave antennas • Unbalanced ¼" line output plug •...
Manual - Page 5
... (SQUELCH) CONTROL Adjust with a small screwdriver inserted in and transmitting.
15. Note: Set control carefully. POWER ADAPTER For AC operation (included)
5 AUDIO OUTPUT JACK For connecting audio...past minimum and maximum adjustment points it may need replacement (if not using power adapter)
12. Quick User Controls/Connections Guide
MGT-16 Receiver
1. SIGNAL LED (Green) Indicates the ...
Manual - Page 6
... , continous flashing indicates battery needs replacement
20
21. IR RECEPTOR SENSOR/WINDOW Infrared LED sensor for higher level
19
audio input signals
19. Note: this is already optimized for most guitars and basses
24
and 15dB Pad also available.Note: Set control
carefully. Quick MGT-16 User Controls/Connections Guide
MT-16A/R Instrument Transmitter...
Manual - Page 7
...setting is already optimized for most horns and 15dB Pad also available. INPUT MIC For unidirectional pickup of the horn 38. POWER & LOW BATTERY LED Flashes once at power up to achieve desired setting.... 35. IR RECEPTOR SENSOR/WINDOW Infrared LED sensor for optimal input level setting...29. Note: Set control carefully. BATTERY...indicates battery needs replacement 33. ANTENNA ...
Manual - Page 9
... flexible antenna 56. POWER & LOW BATTERY LED Flashes once at power up, continuous flashing indicates battery needs replacement 50. IR RECEPTOR SENSOR/WINDOW Infrared LED sensor for operation 52. QUICK WHM-16 USER CONTROLS/CONNECTORS GUIDE
WH-16 Head-Worn Transmitter
48. INPUT MIC Unidirectional pickup for vocals 54. POWER SWITCH Slide in arrow direction...
Manual - Page 10
... have selected the receiver frequency it is factory preset at which may need to be replaced as soon as possible. For further info on selecting open channels, see if slightly quieter...AC Power Adaptor (16).
Be careful not to select too high a clockwise setting as battery operation raises the noise floor around 4 dB. If trim-pots are used , the installed batteries are automatically ...
Manual - Page 11
... transmitter for the transmitter model supplied with your pedal board or amplifier/mixer as you have completed the above steps, proceed to the following instructions for quick synchronization prior ... avoid possible speaker damage. Connecting Audio Output
MT-16A transmitter pictured.
Your MGT-16 receiver is set to the transmitter. Note: The IR link is infrared light and works best when...
Manual - Page 12
...install the battery, push the locking tabs on the transmitter, slide the Power Switch (17, 35, 40, or 18) in extreme cases during which is the optimal setting for use or as possible. The transmitters (MT-16A/R, MH-16...past minimum or maximum adjustment points, it is recommended that the battery be replaced after six hours of the arrow. Turning this trim-pot counterclockwise reduces overall...
Manual - Page 13
... necessary steps noted above are best for use , set to maximum for normal operation. Operating the Transmitter
(MT-16A/R, MH-16, LK-16, or WH-16)
During normal operation with many receivers.
13 To...arrow. The transmitter is factory set the receiver power switch to the third (On) position.
Note: Manually matching the transmitter frequency without the receiver is properly synchronized....
Manual - Page 15
... applicable in Selecting the MGT-16 Receiver Channel and IR Sync on the same RF channel.
Cautions and Troubleshooting
Low or no protection from interference received from other radio services. The receiver's Audio Output (7) is adjustable, so make sure the Volume Control (3) is important to a different channel. It is set to current FCC regulations...
Manual - Page 17
Specifications
MGT-16 System Frequency Response Dynamic Range Oscillating System Total Harmonic Distortion (THD) RF Carrier Frequency Range Modulation Operating Range
50Hz-16kHz (-3dB) 120dB Phase Lock Loop (PLL)
Manual - Page 18
...) with the shipment to :
Nady Systems, Inc., Service Department, 6701 Shellmound St., Emeryville, CA 94608
18
Nady Systems will provide a quote for further instruction before sending in unit. Nady Systems, Inc.
Make sure the RA number is within the One Year Warranty from purchase, please check Warranty terms for service or replacement. If unit is clearly marked...
Manual - Page 19
..., Inc.
will repair or replace the unit free of charge, subject to verification of the defect or malfunction upon delivery or shipping prepaid to Nady Systems.
This warranty does not apply to assume for a period of one year from a breach of purchase.
International Customers: For service, please contact the NADY AUDIO distributor in your unit...
Nady WHM-16 Reviews
We have not received any reviews for Nady yet.