Optoma W505 Support and Manuals
Optoma W505 Videos
Popular Optoma W505 Manual Pages
Datasheet - Page 1
Just a few of installation Optional lenses for maximum installation flexibility
LENS THROW OPTIONS
Optoma Part Number Throw Ratio (Distance/Width) Projection Distance Image Size (Diagonal) Projection Lens
Weight w/ Projector
Short Throw BX-DL080 0.81:1
1.6'- 9.8' (0.5 to 3m) 28.0"-171" (0.71-4.34m) F=2.5, f=11.5 mm, Manual Focus
19.1 lb (8.6 kg)
The Optoma W505 was designed to deliver ...
Datasheet - Page 2
...W505
OPTICAL/TECHNICAL SPECIFICATIONS
Display Technology Single 0.65" DarkChip3™ DLP® Technology by Texas Instruments™
Native Resolution
WXGA (1280 x 800)
Maximum Resolution
WUXGA (1920 x 1200)
Brightness (Typical)
5200 lumens
Contrast Ratio
2,000:1 (full on/full off)
Displayable Colors
1.07 Billion
Lamp... to hardwire to the projector
Operating Temperature 41-113...
User Guide - Page 2
... Problems...80 Replacing the Lamp...81
Cleaning the Projector...83 Compatibility Modes...84
Video Compatibility...84 Video timing detail describe...84 Computer Compatibility - VESA standards 85 RS232 Commands...88 RS232 Protocol Function List...89 Telnet Commands...93 AMX Device Discovery commands 93 PJLink™ supported commands 94 Trademarks...96 Ceiling Installation...97 Optoma Global...
User Guide - Page 5
...
Please follow all replacement instructions. To reduce the risk of the lamp itself. module has been replaced. ▀■ Warning - "Replacing the Lamp" on until the lamp
▀■ Warning - Do not use the lens cap when projector is on -screen display "Options|Lamp Setting" menu after replacing the lamp module (see page 63). Please do not expose this user's guide.
▀■...
User Guide - Page 18
... the user manual of the PC to determine the appropriate Fn key combination to turn On the projector. The startup screen will now flash blue. Turn On the connected devices.
4. The first time you use the projector, you can select your preferred language and Power Mode setup after the startup screen display. Installation
Powering On...
User Guide - Page 20
... off the projector lamp, a message displays on the projector immediately following a power off the main power switch.
Under normal conditions, the projector can be switched on again after 15 seconds.
3. Installation
Powering Off the Projector
1. Disconnect the power cord from the electrical outlet and the projector.
5. Please contact your local dealer or our service center. English...
User Guide - Page 32
... "Tint" is supplied.. Position/V. v (*) "3D" is only available when a compatible signal is only supported in for YUV video sources.. Position/Exit White Level/Black Level/IRE/Exit
Bahasa Indonesia
SETUP | Security SETUP | Audio Settings
SETUP | Advanced SETUP | Network
Security Setting Security Timer Change Password
Exit
Internal Speaker Mute
Volume Audio Input
Exit
Logo Logo Capture Closed...
User Guide - Page 44
... for more information. Network
Allows access to controls for more information.
The function is available when input source is support Video signal. Set projector signal properties. Advanced
Enter the Advanced menu. Access the projector's security features. Set projector signal properties. Select the screen display during startup. Signal(Video)
Enter the Signal (Video) menu. Audio...
User Guide - Page 75
..., please contact your local reseller or service center. choose the resolution mode you need to the Replacing the Lamp section.
4 Make sure you are using a PC:
For Windows 95, 98, 2000, XP: 1.
Select the Change button under the Monitor tab. 7. Appendices
Troubleshooting
If you experience a problem with your projector, please refer to UXGA (1600 x 1200). (*)
75...
User Guide - Page 77
...projector. 4 Move the projector closer to Display | Format and try the different settings.
To replace the lamp, follow the procedures in Replacing the Lamp on the remote control or projector...remote control until the lamp module has been replaced. Intermission Problems
The projector stops responding to the following:
4 Please setup the display format as 4:3 in projector OSD. Image is still...
User Guide - Page 80
... 7m (23 ft) of the audio source. 4 Check the audio cable connection. 4 Test the source audio output with other speakers. 4 Have the projector serviced. English 80 Appendices
Message Reminders 4 Replacing the lamp:
4 Out of range: (see the following for more information)
Remote Control Problems
If the remote control does not work
4 Check the operating angle for...
User Guide - Page 81
... to turn off and unplug the projector at least an hour before
replacing the lamp. It should be replaced when it burns out. Appendices
Replacing the Lamp
The projection lamp should only be
disposed of according to local ordinance regulations.
4 Avoid touching the glass surface of mercury and should be replaced with a certified replacement part, which you can order from...
User Guide - Page 92
Appendices
(5 minutes for each step).
~XX107 n
7E 30 30 31 30 37 20 a 0D
Sleep Timer (min)
n = 0 (a=30) ~ 995 (a=39 39 35)
(30 minutes for each step).
~XX114 1
7E 30 30 31 31 34 20 31 0D
Power Mode(Standby)
Active (
User Guide - Page 95
...; standard specifications Version 1.0. INST? "11 12 21 22 31 32" The projector name set on The following value is returned. v This projector is fully compliant to 5 digits): Cumulative LAMP operating time (This item shows a lamp operating time (hour) calculated based on that LAMP MODE is LOW.) 2nd value: 0 = Lamp off, 1 = Lamp on the NETWORK menu or the ProjectorView Setup window...
User Guide - Page 96
...projector control and you can control and monitor projector's operations using the same application among projectors of different models and different manufacturers.
4 Other product and company names mentioned in the U.S. CLSS? "1" is returned. This projector supports...are trademarks of
Apple Inc., registered in this user's
manual may be the trademarks or registered trademarks of America and ...
Optoma W505 Reviews
Do you have an experience with the Optoma W505 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Optoma yet.
Earn 750 points for your review!