Pfaff hobby 1010 Support and Manuals
Get Help and Manuals for this Pfaff item
This item is in your list!
View All Support Options Below
Free Pfaff hobby 1010 manuals!
Problems with Pfaff hobby 1010?
Ask a Question
Free Pfaff hobby 1010 manuals!
Problems with Pfaff hobby 1010?
Ask a Question
Popular Pfaff hobby 1010 Manual Pages
Owner's Manual - Page 1
INSTRUCTION MANUAL FOR SEWING MACHINE
0]
351427004 0012.14
Hobby Model 1010 - 37
Owner's Manual - Page 2
...
Twin Needle
22
Embroidery
22
Quilter & Seam guide
23
Buttonhole sewing
24
Maintenance (Cleaning and oiling)
25
Checking Performance Problems WHAT TO DO
26 Always use bent needles.
13. The wrong plate can cause the needle to persons:
1. Always unplug sewing machine from all moving parts. IMF'UHIANT 5AFTY INSTRUCTIONS
When using an electrical appliance, basic safety...
Owner's Manual - Page 3
NAME OF PARTS (FRONT VIEW)
(REAR VIEW)
Zigzag width dal resure Regulator
Take up lever
Thread tension dial
Presser toot Shuttle
Extension table
Sub-spool pin pin Top cover Needle position knor Reverse button d al
read guide for upper threading
Bobbin winder
Bobbin winder spindle Upper thread guide
Stop Motion knob Hand wheel
Face...
Owner's Manual - Page 4
Button foot
Machine Oil
Zipper foot
Button hole cutter
Screw driver
-3- When servicing the sewing machine, or when removing covers or changing lamps, the machine must be removed from the socket outlet.
-4- Sewing speed can be disconnected from the supply by removing the plug from the socket outlet. Open face cover in direction arrow.
2. Remove bulb by screwinl ...
Owner's Manual - Page 5
... in correct, release .the screw of upper thread guide and ad just up or down until bobbin winding is filk tighten stop motion kric
2.Thread as a fiat bed machine but easily converts to original position. WINDING ThE BOBBIN
1 Release stop motion kno
:REE.Ai SEWING
1. When bobbin winding is com pleted return spindle...
Owner's Manual - Page 6
... to its highest
zposition and open the shuttle race cover.
2.Open hinged latch of bobbIn case and pull bobbin case out of machine.
3.Release the latch and bob bin will fall out easily.
REMOVING BOBBIN CASE AND BOBBIN
Hinged
1 .Raise needle to the ...into slot and under
tension spring and draw out about 10cm of thread into
bobbin case as shown.
2.Guide the end of thread.
-7-
Owner's Manual - Page 7
... lower thread will be brought up . Place fabric under presser foot to sew.
-10- Lower presser foot and start to the rear of machine.
3. Pull out both threads and place them together under presser foot from the front, lower presser foot.
4.Startto sew (see page 16)
CHANGING SEWING DIRECTIONS
1 Lower needle down and comes up in a loop.
2. THREADING...
Owner's Manual - Page 9
... THE PRESSER FOOT PRESSURE
1.
Push down outer ring to raise feed above needle plate for darning, embroidery, and button sewing.
8. Push down inner pin (A) to increase pressure. (Light to its highest position. 2.Loosen needle clamp screw and remove old needle. 3. Insufficient pressure may cause poor feeding, skipped stitches, or difficulty in guiding the...
Owner's Manual - Page 10
...
Please note that the following list is a guide when sewing different fabrics. Hold both threads about 10 cms to your hand.
3. Attention 1, When 'turning the balance wheel manually, always turn it
toward, you plan to use, adjusting the machine for the first two or three stitches.
3.
Depress foot/Speed control and start to its highest...
Owner's Manual - Page 11
..., etc.
- 18 -
STRAIGHT STITCH
1 This type of
machine.
5.Cut threads as shown on the thread cutter. - 17- TO FINISH SEAM
1 .Sew to the edge of seam. 2.Push the reverse button and sew in reverse 'for
about 3-4 cms. 3.Raise needle to its highest position. 4.Lift presser foot and pulloul the fabric to rear of stitching...
Owner's Manual - Page 12
... close to 6.Pull both holes of the needle. 2. To sew the right side of zipper set the zipper foot on the left side of zipper set the zipper foot on zipper 2. Place button attaching presser foot in position. 3.Place button between presser foot and fabric and lower presser foot. 4.Manually turn hand wheel towards you ensuring that the needle...
Owner's Manual - Page 13
... breaking of twin needle. Raise the foot and the needle to the left needle of needle. During sewing fold the fabric to its highest position. Lower the foot and sew the hem. 4. Insert other thread into the
hemmer foot. 5. Separate threads before last thread guide above the needle. CAUTION:Do not set stitch width wider than number...
Owner's Manual - Page 14
... THE END OF THE MARKING FIGURE (4).
7.
REMOVE THE REGULAR PRESSER FOOT AND ATTACH THE BUTTONHOLE FOOT & PUT THE FAE UNDER ThE BUTTONHOLE FOOT.
3. Set guide hole on top of presser foot holder. .Move guide to the guide for desired seam allowance. 3.
Run machine with cutter as shown. BUTTONHOLE SEWING
1.MARK WITH A PENCIL OR CHALK THE EXACT LENGTH OF THE BUTTONHOLE...
Owner's Manual - Page 15
.... -
Tension too tight - Incorrect use of fabric, and
thread. Clean shuttle.
- CCD. Incorrect setting of needle, thread or fabric,
- Tight upper thread tension. - Fit new needle. - Do not pull fabric. - Replace shuttle, or polish off
burrs completely.
Adjust sewing foot pressure. - Use correct fabric, needle and
thread. C.
0 CD CD
3' 0
(V
C, C'0CD DC
C 0 'C 0•
"4 (a,
0 CD...
Pfaff hobby 1010 Reviews
Do you have an experience with the Pfaff hobby 1010 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Pfaff yet.
Earn 750 points for your review!