Pfaff hobby 1037 Support and Manuals
Get Help and Manuals for this Pfaff item
View All Support Options Below
Free Pfaff hobby 1037 manuals!
Problems with Pfaff hobby 1037?
Ask a Question
Free Pfaff hobby 1037 manuals!
Problems with Pfaff hobby 1037?
Ask a Question
Popular Pfaff hobby 1037 Manual Pages
Owner's Manual - Page 1
INSTRUCTION MANUAL FOR SEWING MACHINE
0]
351427004 0012.14
Hobby Model 1010 - 37
Owner's Manual - Page 2
... unplug this manual. To disconnect, turn all instructions before using and before relamping, Replace bulb with any opening.
8.
Needle table
15
To start sewing
16
To finish seam
17
Straight stitch
18
Zigzag sewing
18
Button sewing
19
Zipper sewing
20
Hemming
21
Twin Needle
22
Embroidery
22
Quilter & Seam guide
23
Buttonhole sewing
24
Maintenance (Cleaning...
Owner's Manual - Page 3
NAME OF PARTS (FRONT VIEW)
(REAR VIEW)
Zigzag width dal resure Regulator
Take up lever
Thread tension dial
Presser toot Shuttle
Extension table
Sub-spool pin pin Top cover Needle position knor Reverse button d al
read guide for upper threading
Bobbin winder
Bobbin winder spindle Upper thread guide
Stop Motion knob Hand wheel
Face...
Owner's Manual - Page 4
...
Zipper foot
Button hole cutter
Screw driver
-3- When servicing the sewing machine, or when removing covers or changing lamps, the machine must be disconnected from the supply by removing the plug from the socket outlet.
Plug the machine to the po y supply.
3.
Remove bulb by screwinl ri clockwise.
4. Install a now bulb by unscre ing it counter-clockwise...
Owner's Manual - Page 5
...guide and ad just up or down until bobbin winding is in diecfion or
arrow. When bobbin winding is balanced.
-6- REMOVING EXTENSION TABLE
1 Hold the left end of table and pull out in correct, release .the screw of arrow. Especially useful for sewing...:REE.Ai SEWING
1.
This sewing machine can be used as shown.
3.When bobbIn is com pleted return spindle to free arm machine by removing the...
Owner's Manual - Page 6
... latch open the latch of bobbin case and hold it into
bobbin case as shown.
2.Guide the end of thread into slot and under
tension spring and draw out about 10cm of thread...case onto centre pin shuttle and release latch -8-
INSERTING BOBBIN INTO BOBBIN CASE
insertI.PulI off 5cm of machine.
3.Release the latch and bob bin will fall out easily. REMOVING BOBBIN CASE AND BOBBIN
Hinged
1...
Owner's Manual - Page 7
...threads and place them together under presser foot from the front, lower presser foot.
4.Startto sew (see page 16)
CHANGING SEWING DIRECTIONS
1 Lower needle down and comes up in a loop.
2. DRAWING UP BOBBIN THREAD... lower thread will be brought up . Place fabric under presser foot to the rear of machine.
3.
Hold upper thread with left hand, turn the hand wheel slcwly towards you until ...
Owner's Manual - Page 9
...to release pressure. (Heavy fabrics)
3. No pressure adjustment is required when darn ing or sewing embroidery.
With the flat side of the needle facing away from you,
insert needle as ...feeding, skipped stitches, or difficulty in guiding the fabric.
4. Push feed ever up as far up to raise feed above needle plate for darning, embroidery, and button sewing.
8. Push down to its highest ...
Owner's Manual - Page 10
Attention 1, When 'turning the balance wheel manually, always turn it
toward, you stop sewing.
-15-
16 -
- FABRIC THREAD NEEDLE TABLE
Please note that the following list is a guide when sewing different fabrics. Sufficient fabric should be placed under needle before starting and
after stopping sewing.
2. Test the machine stitches on a scrap of fabric you plan to use...
Owner's Manual - Page 11
... and pulloul the fabric to page 15 for sewing initials, patterns, applique, etc.
- 18 - STRAIGHT STITCH
1 This type of stitching is the one used most frequently. 2.The zig-zag presser foot can be used for dial
setting). TO FINISH SEAM
1 .Sew to the edge of
machine.
5.Cut threads as shown on the thread cutter...
Owner's Manual - Page 12
.... (Increase or decrease width setting). 5.Sew about 2 cm and place fabric under foot
1. to a raised edge preventing sowing on the right side of the needle. 2. BLflTON SEWING
1 .Lower drop feed. 2. Place button attaching presser foot in position. 3.Place button between presser foot and fabric and lower presser foot. 4.Manually turn hand wheel towards you...
Owner's Manual - Page 13
... groove under the foot. CAUTION:Do not set stitch width wider than number 2 setting. The
fabric must be necessary to run ...threads before last thread guide above the needle. HEMMING Note: Hemmer foot can be purchased separately
1. Lower the foot and sew the hem. 4....the
same path as for normal sewing.
Replace the toot with a few stitches. During sewing fold the fabric to form the...
Owner's Manual - Page 14
...r(2)
(3)
(4)
01
41
1. Run machine with cutter as shown. SET STITCH LENGTH ABOUT 0.5, ZIGZAG WIDTh KNOB ABOUT '2' NEEDLE POSITION KNOB ON L POSITION, THEN SEW AS FIGURE (2) IJNTILL YOU REACHES THE END OF THE MARKING. 5. Set guide hole on top of material touching guide.
23 -
-
SEAM GUIDE
Note: Seam guide can be purchased separately. BUTTONHOLE SEWING
1.MARK WITH A PENCIL OR...
Owner's Manual - Page 15
...
0 CD CD
3' 0
(V
C, C'0CD DC
C 0 'C 0•
"4 (a,
0 CD
.4
0 'C
C0'CD DC
0. 0
0
z
'a,
0.
Sewing foot pressure too strong. -
C. Tight stop motion. - CD
CCD.
0
-4.
Fit new needle. - C)
CDDC
CD CCDD
C. 0.
CD
5: -. Light pressure on presser foot.
- Incorrect setting of fabric, and
thread. Re-thread machine. - Incorrect use of needle, thread or fabric,
- Needs...
Pfaff hobby 1037 Reviews
We have not received any reviews for Pfaff yet.