Owner's Manual
Page 3
...handling. ! This unit is for vehicles with liquids. Always use of an improper fuse could result in fire, generation of the car's body. Always install the amplifier on a surface with and identical equivalent. ! Doing so could result. Do not allow parts such as - If this product or cords ... is cut off and check the power supply and speaker connections. sociated with accessories sold battery wire or the amplifier fuse blows. Be sure to install the fuse to get caught between the amplifier and the automobile. If you . ! CAUTION ! Do not turn up and cause minor burns. !...
...handling. ! This unit is for vehicles with liquids. Always use of an improper fuse could result in fire, generation of the car's body. Always install the amplifier on a surface with and identical equivalent. ! Doing so could result. Do not allow parts such as - If this product or cords ... is cut off and check the power supply and speaker connections. sociated with accessories sold battery wire or the amplifier fuse blows. Be sure to install the fuse to get caught between the amplifier and the automobile. If you . ! CAUTION ! Do not turn up and cause minor burns. !...
Owner's Manual
Page 8
...volume until the mute function is from 1 W to 8 W to two speakers The output from the antenna, antenna cable and tuner. Install and route the separately sold battery wire as far as possible from catching fire, generating smoke and/or being damaged. ! Precautions for parallel ...together multiple speaker's negative cables. ! When connecting to one speaker Speaker output When connecting to prevent the amplifier from the speaker wires. Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as that the synthetic impedance is ...
...volume until the mute function is from 1 W to 8 W to two speakers The output from the antenna, antenna cable and tuner. Install and route the separately sold battery wire as far as possible from catching fire, generating smoke and/or being damaged. ! Precautions for parallel ...together multiple speaker's negative cables. ! When connecting to one speaker Speaker output When connecting to prevent the amplifier from the speaker wires. Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as that the synthetic impedance is ...
Owner's Manual
Page 11
...location such as near the heater outlet. ! Places where it could injure the driver or passengers if the vehicle stops suddenly. - After installing the amplifier, confirm that the screw tip does not touch any parts other than those supplied are behind the panel and protect all cables and...places, such as under the dashboard. Tapping screws (3 mm × 10 mm (1/8 in. × 3/8 in.)) Example of the ampli- Do not install in the desired installation location. Insert the supplied tapping screws (4 mm × 18 mm (5/32 in. × 3/4 in.)) into the screw holes and push on the floor...
...location such as near the heater outlet. ! Places where it could injure the driver or passengers if the vehicle stops suddenly. - After installing the amplifier, confirm that the screw tip does not touch any parts other than those supplied are behind the panel and protect all cables and...places, such as under the dashboard. Tapping screws (3 mm × 10 mm (1/8 in. × 3/8 in.)) Example of the ampli- Do not install in the desired installation location. Insert the supplied tapping screws (4 mm × 18 mm (5/32 in. × 3/4 in.)) into the screw holes and push on the floor...
Owner's Manual
Page 12
Section 04 Installation 3 Install the amplifier with the use of supplied tapping screws (4 mm × 18 mm ( 5/32 in. × 3/4 in.)). 1 3 2 4 5 1 Tapping-screws (4 mm × 18 mm (5/32 in. × 3/4 in.)) 2 Drill a 2.5 mm (3/32 in.) diameter hole. 3 Floor mat or chassis 4 Hole-to-hole distance: 257 mm (10-1/8 in.) (GM-D8601) / 307 mm (12-1/8 in.) (GMD9601) 5 Hole-to-hole distance: 181 mm (7-1/8 in.) (GM-D8601) / 181 mm (7-1/8 in.) (GMD9601) 12 En
Section 04 Installation 3 Install the amplifier with the use of supplied tapping screws (4 mm × 18 mm ( 5/32 in. × 3/4 in.)). 1 3 2 4 5 1 Tapping-screws (4 mm × 18 mm (5/32 in. × 3/4 in.)) 2 Drill a 2.5 mm (3/32 in.) diameter hole. 3 Floor mat or chassis 4 Hole-to-hole distance: 257 mm (10-1/8 in.) (GM-D8601) / 307 mm (12-1/8 in.) (GMD9601) 5 Hole-to-hole distance: 181 mm (7-1/8 in.) (GM-D8601) / 181 mm (7-1/8 in.) (GMD9601) 12 En