Owner's Manual
Page 3
...At least two qualified people should be taken at all times during the installation of impact. Mounting structure recommended wood studs, solid-flat concrete, and reinforced metal studs. The wall or ceiling structure must be disconnected from dropping or mishandling the plasma television. The installation instructions ...Injury and damage can result from the power outlet. Do not install in plasma cracking or falling from the wall causing damage and injury. If installing the mount on other source of plasma display. Failure to do so may result in damage to the plasma television and...
...At least two qualified people should be taken at all times during the installation of impact. Mounting structure recommended wood studs, solid-flat concrete, and reinforced metal studs. The wall or ceiling structure must be disconnected from dropping or mishandling the plasma television. The installation instructions ...Injury and damage can result from the power outlet. Do not install in plasma cracking or falling from the wall causing damage and injury. If installing the mount on other source of plasma display. Failure to do so may result in damage to the plasma television and...
Owner's Manual
Page 4
Mounting points for power or cables. Access hole for additional security screws. 1.000 1.750 1.250 19.771 16.000 5.460 2.865 e F 3.500 A d 8.000 18.500 5.000 4.500 8.000 b 3.250 4.500 5.460 16.000 c MOUNTING BRACKET PART#: Mounting bracket MATERIAL: 12 (GA) P & O COLOR: Black Powder coat - 4 - D. Mounting points (4.5") used on installations other than wall mounting. B. C. Mount Diagrams TILT BACK PLATE PART#: 1.125 PSB-TBP MATERIAL: 12 (GA) CRS COLOR: Black powder coat A. Lag bolt access slot.
Mounting points for power or cables. Access hole for additional security screws. 1.000 1.750 1.250 19.771 16.000 5.460 2.865 e F 3.500 A d 8.000 18.500 5.000 4.500 8.000 b 3.250 4.500 5.460 16.000 c MOUNTING BRACKET PART#: Mounting bracket MATERIAL: 12 (GA) P & O COLOR: Black Powder coat - 4 - D. Mounting points (4.5") used on installations other than wall mounting. B. C. Mount Diagrams TILT BACK PLATE PART#: 1.125 PSB-TBP MATERIAL: 12 (GA) CRS COLOR: Black powder coat A. Lag bolt access slot.
Owner's Manual
Page 7
... mark the desired height by marking the wall mount. See fig 3. Wall structure Desired height marking Stud centers marking 16" Wood studs behind the wall using a (commercially available) stud finder and mark the center of this product. At least two (2) qualified personnel are ...of the studs when found. Please verify that your installation requirements. Installing the mounts Step 3 CAUTION: The plasma displays are fragile and heavy. Locate the 16" wood stud centers behind the wall structure Adjusting the mount Tilt back plate CENTER OF VIEWING HEIGHT floor floor - 7 - Select ...
... mark the desired height by marking the wall mount. See fig 3. Wall structure Desired height marking Stud centers marking 16" Wood studs behind the wall using a (commercially available) stud finder and mark the center of this product. At least two (2) qualified personnel are ...of the studs when found. Please verify that your installation requirements. Installing the mounts Step 3 CAUTION: The plasma displays are fragile and heavy. Locate the 16" wood stud centers behind the wall structure Adjusting the mount Tilt back plate CENTER OF VIEWING HEIGHT floor floor - 7 - Select ...
Owner's Manual
Page 8
... slot opening into the 1/4" pilot hole. Before continuing, confirm the marks are located on the mounting bracket. See fig 4. Access holes Put the lag bolt through the upper left and right slot openings on the wall. Raise the tilt back plate and have someone hold it in the lower left slot opening... the height is determined, use the bubble level to insure that the bracket is still leveled and then screw a lag bolt to ensure that the wall mount is level. Make any lateral positioning if any then secure the lag bolts. Drill 1/4" pilot holes on the six (6) markings on the...
... slot opening into the 1/4" pilot hole. Before continuing, confirm the marks are located on the mounting bracket. See fig 4. Access holes Put the lag bolt through the upper left and right slot openings on the wall. Raise the tilt back plate and have someone hold it in the lower left slot opening... the height is determined, use the bubble level to insure that the bracket is still leveled and then screw a lag bolt to ensure that the wall mount is level. Make any lateral positioning if any then secure the lag bolts. Drill 1/4" pilot holes on the six (6) markings on the...
Owner's Manual
Page 9
... 5 Warning: The plasma display is heavy and 2 people are interlocked with the way the plasma mount attaches to the wall mount. See the diagram on the tilt back plate before letting go of the plasma. When all (4) tab openings are needed to lift and install... (4) Tab openings Locked tab Caution: All four (4) receiving tab openings from the mounting bracket must be locked to the tabs found on the left to lock the mounts together. Before placing the plasma on the wall recheck all four (4) tab openings to lock in serious personal injury. See fig 5. Before ...
... 5 Warning: The plasma display is heavy and 2 people are interlocked with the way the plasma mount attaches to the wall mount. See the diagram on the tilt back plate before letting go of the plasma. When all (4) tab openings are needed to lift and install... (4) Tab openings Locked tab Caution: All four (4) receiving tab openings from the mounting bracket must be locked to the tabs found on the left to lock the mounts together. Before placing the plasma on the wall recheck all four (4) tab openings to lock in serious personal injury. See fig 5. Before ...