Ridgid R4010 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid R4010 manuals!
Problems with Ridgid R4010?
Ask a Question
Free Ridgid R4010 manuals!
Problems with Ridgid R4010?
Ask a Question
Most Recent Ridgid R4010 Questions
Popular Ridgid R4010 Manual Pages
Owners Manual - Page 1
..., and operator safety. WARNING:
To reduce the risk of rugged, trouble-free performance.
SAVE THIS MANUAL FOR FUTURE REFERENCE Tile SAW
R4010
14 13 12 11 10 9 8
Your tile saw has been engineered and manufactured to our high standards for , it will give you for buying a RIDGID® product. Thank you years of injury, the user must read...
Owners Manual - Page 3
...parts, binding of moving parts. All visitors should be properly repaired or replaced by an authorized service...parts, breakage of checking to determine that it was not designed for outdoor use it on the saw 's applications and limitations as well as the specific...OFF. English READ ALL INSTRUCTIONS
KNOW YOUR ... jewelry. Read the operator's manual carefully. For example, pipes,...
Owners Manual - Page 8
... is used, to prevent water traveling along the cord and coming in contact with wet hands. To avoid the possibility of the tool plug or outlet getting wet, position tile saw to one side of electrocution, keep all connections dry and off the ground. Disconnect the fuse or circuit breaker that part of the cord below...
Owners Manual - Page 9
... GUIDE
SLIDING TABLE LOCK LEVER
RUBBER BOOT
14 13 12 11 10
9
8
WATER TRAY FRAME
TABLE STOP BY-PASS
SPAN-DECK CLAMP
READY RACK™ TILE CARRIER
VARIABLE FLOW VALVE
CLEANING NOZZLE
TABLE STOP
DRAINAGE
WSUV™ LEG
STAND
Diverter
VALVE SEDIMENT
WATER TRAY
SEPARATION SYSTEM™
WATER TANK
DRAIN PLUG
9 - Diagonal Capacity (tile size 18 in . FEATURES
PRODUCT SPECIFICATIONS...
Owners Manual - Page 10
...º bevel angles. The clamp supports mosaic tile for accurate cuts. Using the universal pump and water tank together keeps water circulating to slide the workpiece into the main tray.
WSUV™ Wet Saw Utility Vehicle - Failure to -read indicator on when the saw . The easy-to heed this tool. To lock the switch, install a padlock (not included) through...
Owners Manual - Page 11
...tube 1 W - Carrage bolt 8 Z - Water tray extensions 2 M - Hex key, 3 mm, 4 mm, 8 mm 3 CC - English LOOSE PARTS
The following items are included with cleaning nozzle 1 P - Spacer 8 X - Span-deck clamp 1 FF - Long clear tube with your tile saw:
B A
I - Lower brace 1
S - Long clear tube 1 F - Long tube assembly 1 T - Sliding table extension 1 II - Lock...
Owners Manual - Page 12
...connect to the product by the manufacturer and require customer installation. This product requires assembly. Carefully lift the saw is complete. Tighten securely.
After assembling it . If shipping has influenced the settings, refer to modify this manual.
If any parts on this tool. For easier assembly, match letter to make sure no breakage or damage occurred...
Owners Manual - Page 14
..., etc.
English ASSEMBLY
Installing the water tray frame assembly to the leg stand
See Figure 7. Lock the table stop by-pass by...Installing clear tubes, cleaning nozzle, and water pump TO the saw arm by -pass
Leg stand
Short carriage
bolt
Hex nut
Fig. 7
Motor head assembly
Connector
Cap bolt (short)
Sleeve
Water tray frame
Cap bolt (long)
Fig. 8
Clear tube
valve ASSEMBLY...
Owners Manual - Page 15
... plug pump into the slots on the
sliding table fence. Installing the miter guide
See Figure 14.
English
Water tray extension
Fig. 13
ASSEMBLY
Push the short clear tube of the T-connector assembly over cord connections to the submersible water pump and set the pump in the bottom of the water tray frame. Pull boot over the connector on the...
Owners Manual - Page 16
... rack™ tile carrier
See Figure 16.
installing sliding table extension
See Figure 15. From the side of the saw .
ASSEMBLY
Lock the miter guide securely to the table by turning the table extension lock knob
underneath the extension clockwise.
The carrier provides a storage area for cut tiles while the holes in the bottom allow water to the...
Owners Manual - Page 19
... spindle. Never use the 10 in . WARNING:
If the washer has been removed, replace it before placing wheel on the spindle. Spindle lock
To tighten
To loosen
Wheel wrench
... situations could result in personal injury. Installing TILE CUTTING WHEEL
See Figures 22 - 23. Never use wheels that you are available at your saw. ASSEMBLY
tile cutting wheel
For maximum performance and safety...
Owners Manual - Page 21
...tile, pavers, and stone tile products only.
Using the pump and cleaning nozzle
See Figure 26.
The use the submersible pump: Unscrew the drain plug located under the water tray. Fill the water tank two-thirds full. Center the water...
Fig. 26 Pump switch on with tools to run water through the saw arm, has three positions: A) With the pump switch...
Owners Manual - Page 23
... before removing any part of the material.
Once you've strayed from the marked line.
OPERATION
MAKING CUTS
Always draw the line to be cut on material.
Set the miter guide to 0°, ...the table and firmly against the miter guide and fence.
Make sure the material is clear of the cutting wheel before turning on the saw.
Turn the on/off a small amount of tile until...
Owners Manual - Page 24
... the material at any angle to be cut on the saw OFF. NOTE: Only overcut on the bottom or underneath side of tile to fit in place, and tighten the lock knob.
Place the material on the table and firmly against the miter guide and feed the material into the wheel. Hold...
Owners Manual - Page 28
... loaded and will not run the clean water through the saw and water pump.
Empty the dirty water from the water tank and dry off the tool.
Once the table has been removed, rinse the rails and water tray, and water tray frame.
Replace the drain plug.
Brush cap
Brush assembly
Brush assembly
Brush cap
Fig. 39
Cleaning the rails...
Ridgid R4010 Reviews
We have not received any reviews for Ridgid yet.