Ridgid RP 330-B Support and Manuals
Get Help and Manuals for this Ridgid item
This item is in your list!
View All Support Options Below
Free Ridgid RP 330-B manuals!
Problems with Ridgid RP 330-B?
Ask a Question
Free Ridgid RP 330-B manuals!
Problems with Ridgid RP 330-B?
Ask a Question
Popular Ridgid RP 330-B Manual Pages
Owners Manual - Page 1
pág. 27 Failure to understand and follow the contents of this tool.
Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury.
• Français - 13 • Castellano - RP 330 Manual
Pressing Tool
WARNING!
Owners Manual - Page 2
... Scissor Jaw Set ...7 Pressing A Fitting With Typical Actuator and Press Ring Set 8 Inspecting The Pressed Connection ...9 Maintenance Instructions Cleaning and Lubrication ...10 Required Maintenance at RIDGID Authorized Service Center 10 Accessories ...10 Storage ...10 Service and Repair ...10 Troubleshooting ...11 RP 330 Diagnostic Codes ...12 Lifetime Warranty ...Back Cover
ii
Ridge Tool...
Owners Manual - Page 3
RP 330
Pressing Tool
RP 330-B Battery Tool
RP 330-C Corded Tool
RP 330 Pressing Tool
Record Serial Number below and retain product serial number which is located on nameplate. Serial No.
Owners Manual - Page 4
... indicates the risk of the equipment.
RP 330 Pressing Tool
Safety Symbols
In this manual is the safety alert symbol. Unmodified plugs and matching outlets will reduce risk of flammable liquids, gases, or dust. The operator's manual contains important information on the product, safety symbols and signal words are used to alert you to potential personal injury...
Owners Manual - Page 5
... that is not in a hazardous situation. Power tools are caused by a qualified repair person using only identical replacement parts. Many accidents are dangerous in accordance with specifically designated battery packs. Properly maintained cutting tools with water. in the hands of fire when used for the connection of the power tool may result in the off-position before...
Owners Manual - Page 6
... RP 330-B only)
WARNING Read the battery charger manual before operating the RP 330. An attachment that is specific to keep this tool. Do not expose to repair a damaged jaw set .
Please call Ridge Tool Company, Technical Services for any reason. Description, Specifications and Standard Equipment
Description
The RP 330 Pressing Tool, when used with a new jaw set , press...
Owners Manual - Page 7
... Series • Compact Series These jaw sets are found , do not use machine until the cord or battery has been properly repaired or replaced.
2. Similarly, only compact series jaw sets will work with standard series tools (RP 330, 320-E, CT-400). Inspect the pressing tool for any broken, worn, missing, mis-aligned or binding parts or any problems are protected under various U.S. Confirm...
Owners Manual - Page 8
... operator. See Figure 4. RP 330 Pressing Tool
4.
For a complete listing of RIDGID attachments available for the application. Tool and Work Area Set-Up
WARNING
Set up , and then the green LED will not operate unless the mounting pin is not explosion proof and can cause injury, damage the tool and make incomplete connections. Do not use the machine while standing...
Owners Manual - Page 9
... specific installation instructions. Always follow the specific attachment and fitting installation instructions may result in the appropriate fitting system's operator's manual. Failure to follow the specific instructions for the use an extension cord that the tool and work area has been properly set installed.
2. Pressing A Fitting With Typical Scissor Jaw Set
1. For the RP 330...
Owners Manual - Page 10
... five (5) seconds. RP 330 Pressing Tool
Figure 6 - Placing Scissor-Style Jaw Set Around Fitting
Figure 8 - The press cycle takes about five (5) seconds. This assures consistent, repeatable press joint integrity. Press jaw arms to the tub- For the RP 330-C plug the tool into the base of the handle. Depress ON/OFF button on display panel one time to a RIDGID Authorized Service Center for...
Owners Manual - Page 11
... NOTICE The RP 330 Pressing Tool will not run if it . A fully charged battery should be sent to successfully complete a pressed connection. If the fitting is too low to a RIDGID Authorized Service Center for specific inspection criteria. RP 330 Pressing Tool
point injuries, keep fingers away from fitting by manually grasping ring halves and opening assembly. Installing Press Ring Onto...
Owners Manual - Page 12
... jaws in extreme heat or cold. This will not allow the tool to warm or cool to a temper- WARNING Store the carrying case in the hands of this tool, see the Ridge Tool Catalog on the display panel. Service and repair on this RP 330 Pressing Tool must be indicated by a RIDGID Authorized Service Center.
To prevent serious injury, use only the accessories specifically...
Owners Manual - Page 13
... or too hot. Unplug and replug power cord or remove and reinsert fully charged battery. Used wrong jaw set .
Ridge Tool Company
11 RP 330 Pressing Tool
Troubleshooting
SYMPTOM
POSSIBLE REASONS
SOLUTION
Tool will not begin press cycle when trigger switch is depressed.
Contact Ridge Tool Company, Technical Service Department at (800) 519-3456 for the tube size or material. Red LED...
Owners Manual - Page 14
... cycles or after 30,000 cycles.
Out of acceptable voltage range - If using extension cord,
use 16 AWG for 50' or less, 14 AWG for 50' to a reliable voltage supply. Service indicator after a malfunction.
12
Ridge Tool Company Machine is locked - RP 330 Pressing Tool
RP 330 Diagnostic Codes
LED
Green
Status
Glows Blinks
Red Yellow
Blinks Glows
Blinks Glows
Description...
Ridgid RP 330-B Reviews
Do you have an experience with the Ridgid RP 330-B that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ridgid yet.
Earn 750 points for your review!