Sanyo PLC-XP40 - XGA LCD Projector Support and Manuals
Get Help and Manuals for this Sanyo item
View All Support Options Below
Free Sanyo PLC-XP40 manuals!
Problems with Sanyo PLC-XP40?
Ask a Question
Free Sanyo PLC-XP40 manuals!
Problems with Sanyo PLC-XP40?
Ask a Question
Popular Sanyo PLC-XP40 Manual Pages
Owners Manual - Page 2
Be especially careful that children do not stare directly into the lens as the laser pointer function from Laser Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to this manual thoroughly and operate the projector properly. q Remote Control Unit, supplied to indicate laser emission). Eye damage may result in a fire hazard...
Owners Manual - Page 4
...the following code: Green...Model Number Trade Name Responsible party Address
Telephone No.
: PLC-XP40 : Sanyo : SANYO...instructions.
WARNING : THIS APPARATUS MUST BE EARTHED. Reorient or relocate the receiving antenna. - Do not make any changes or modifications to defeat this projector meets the requirement for a Class B digital device, pursuant to part...a particular installation.
If such...
Owners Manual - Page 5
... EACH PART OF PROJECTOR
7
MANUAL PC ADJUSTMENT
24
SETTING-UP PROJECTOR
8
COMPATIBLE COMPUTER SPECIFICATIONS
26
CONNECTING AC POWER CORD
8
PICTURE IMAGE ADJUSTMENT
27
POSITIONING PROJECTOR
9
... ADJUSTMENT
34
OPERATION OF REMOTE CONTROL
14 SETTING
35
LASER POINTER FUNCTION
14
REMOTE CONTROL BATTERIES INSTALLATION
15
TOP CONTROLS AND INDICATORS
16
SETTING MENU
35
OPERATING ON...
Owners Manual - Page 6
... of your computer is no need for troublesome manual adjustment of frequency and other settings. There is over than 1280 x 1024, reset a computer output for lower resolution. No complicated setup is necessary and projection is automatically set by digitally altering projection to focus on again when a projector detects signal or any button is not pressed...
Owners Manual - Page 8
... does not match your AC outlet, contact your authorized dealer or service station if you use .
Consult your sales dealer. When this equipment...projector on your projector. To POWER CORD CONNECTOR on . (Refer to a projector. Connect a projector with chart below and proper AC Power Cord must be easily accessible. PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector...
Owners Manual - Page 12
...computer. CONTROL PORT
12
x MAC ADAPTER
Set switches as shown in table
below .
VGA Cable
DVI Cable ✽
USB Cable ✽
Audio Cable ✽ (stereo)
Control Cable Control Cable Control Cable ...PS/2 port ADB port
BNC Cable ✽
MAC Adapter Set slide switches according to use
before computer is not supplied with this projector.)
• VGA Cable (HDB 15 pin)
•...
Owners Manual - Page 19
... on Remote Control Unit to operate.
Indicator continues to flash, contact sales dealer where you can turn off ?" Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on again. Turn a projector on page 38.) 4. LAMP Indicator lights RED, and READY Indicator lights GREEN.
During this "Cooling Down" period, this projector or service center.
19...
Owners Manual - Page 23
...setting. (Some computers need setting manually.)
Note : Projector may display one of MANUAL PC ADJUSTMENT section (P25). Auto ---- Make sure connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on Remote Control Unit. Custom Mode (1~5) set... to "COMPATIBLE COMPUTER SPECIFICATION" on this dialog box can be selected. When projector cannot recognize connected signal...
Owners Manual - Page 24
... an image as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. Press POINT LEFT/RIGHT button to recall setting for a specific computer whenever you use it. This projector has a Manual PC Adjustment to enable you want to memorize those special signal formats. This enables you to adjust value. Press POINT LEFT...
Owners Manual - Page 28
...to increase contrast. (From 0 to 63.)
IMAGE ADJUST MENU
Move a red frame pointer to item to set and then press SELECT button.
28 Move a red frame pointer to Image 1 to 4 where you want...button.
Adjust each item is displayed. Level of contrast. (From 0 to 15.)
3
Store
To store manually preset image, move a red frame pointer to item that you want to previous figure. White balance (...
Owners Manual - Page 37
... you control a projector by computer, install USB driver (optionally sold parts) and set up computer following steps below. POINT buttons and two CLICK buttons are pressing. When ONSCREEN MENU or any message / dialog box is not available for wireless mouse operation.
POINT button
Used to item and then press POINT LEFT/RIGHT button(s). INSTALLATION
To use Wireless Remote Control...
Owners Manual - Page 39
...glass bulb! Glass can be ordered through your projector : PLC-XP40 q Replacement Lamp Type No. : POA-LMP38
(Service Parts No. 610 293 5868)
LAMP REPLACE COUNTER...SETTING Menu icon (refer to page 35, 36).
2 Press POINT DOWN button to move a red frame pointer to an end, LAMP REPLACEMENT indicator lights yellow.
q Model No. APPENDIX
LAMP REPLACEMENT
When life of Projection Lamp of this projector...
Owners Manual - Page 40
... sound. If indicator flashes red, a projector cannot be turned on. (See "TURNING ON/OFF PROJECTOR" section on page 19.)
q Check Projection Lamp. (Refer to a warm temperature location
may be with your graphics controller rather than with your dealer or service center for assistance, check matters below once again.
1. APPENDIX
TROUBLESHOOTING
Before calling your computer or...
Owners Manual - Page 41
...can often correct operating problems yourself. It is necessary, contact Sanyo Service Station or store where you find that service is designed and manufactured to work . q Check cable connection between Infrared Remote Receiver and Remote Control Unit.
If a projector fails to meet rigid U.L. If after following all operating instructions, you purchased unit. Give model number and explain...
Owners Manual - Page 42
... (Control port), USB port (Series B receptacle) and Wired Remote Jack
INT. APPENDIX
TECHNICAL SPECIFICATIONS
Projector Type Dimensions (W x H x D) Net Weight LCD Panel...Manual AC Power Cord Wireless/Wired Remote Control Transmitter and Batteries Remote Control Cable VGA Cable MAC/VGA Adapter 3 Types Control Cable (For PS/2, Serial and ADB port) Protective Dust Cover Lens Cover
q Specifications...
Sanyo PLC-XP40 Reviews
We have not received any reviews for Sanyo yet.