Release notes for Dante firmware 1.5.0 for TeamConnect Ceiling 2
Page 1
...Dante network settings Dante Firmware version 1.1.0 - TeamConnect Ceiling 2 Release Notes TeamConnect Ceiling 2 - Update • Version alignment from 1.4.7 -> 1.5.0 Firmware Update • The Dante™ firmware update requires Audinate's Dante Controller software: www.audinate.com/products/software/dante-controller Previous Releases Dante Firmware version 1.4.7... Dante Firmware version 1.3.0 - Release Date 2019-08-30 • Dante Model Name changed to "Sennheiser TCC2" • Additional Dante input channel enabled "AEC Ref" (AEC reference channel) • This update is necessary ...
...Dante network settings Dante Firmware version 1.1.0 - TeamConnect Ceiling 2 Release Notes TeamConnect Ceiling 2 - Update • Version alignment from 1.4.7 -> 1.5.0 Firmware Update • The Dante™ firmware update requires Audinate's Dante Controller software: www.audinate.com/products/software/dante-controller Previous Releases Dante Firmware version 1.4.7... Dante Firmware version 1.3.0 - Release Date 2019-08-30 • Dante Model Name changed to "Sennheiser TCC2" • Additional Dante input channel enabled "AEC Ref" (AEC reference channel) • This update is necessary ...
TeamConnect Ceiling 2 - Planning Guide for System Integrators PDF
Page 3
... of the device to the system settings while the unit is classified as "excellent" speech intelligibility. Planning guide for system integrators TeamConnect Ceiling 2 Planning guide for system integrators 2023-01 | v2.0 Introduction This document is intended for system integrators and room planners and ...Dealing with short or abrupt speech, such as concerts or musicals. Using the Control Cockpit software, you can then make manual or automatic changes to achieve complete three-dimen- Sennheiser electronic GmbH & Co. KG provides both unidirectional and bidirectional speech. The TCC2 is ...
... of the device to the system settings while the unit is classified as "excellent" speech intelligibility. Planning guide for system integrators TeamConnect Ceiling 2 Planning guide for system integrators 2023-01 | v2.0 Introduction This document is intended for system integrators and room planners and ...Dealing with short or abrupt speech, such as concerts or musicals. Using the Control Cockpit software, you can then make manual or automatic changes to achieve complete three-dimen- Sennheiser electronic GmbH & Co. KG provides both unidirectional and bidirectional speech. The TCC2 is ...
TeamConnect Ceiling 2 - Planning Guide for System Integrators PDF
Page 12
... audio source. The yellow dot and conical beam in the Control Cockpit software. Fig. 16: Exclusion Zone of interference could be created and activated simultaneously. The Exclusion Zones enable you to precisely define an Exclusion Zone for system integrators TeamConnect Ceiling 2 Some rooms are no longer picked up to five Exclusion Zones in...
... audio source. The yellow dot and conical beam in the Control Cockpit software. Fig. 16: Exclusion Zone of interference could be created and activated simultaneously. The Exclusion Zones enable you to precisely define an Exclusion Zone for system integrators TeamConnect Ceiling 2 Some rooms are no longer picked up to five Exclusion Zones in...
TeamConnect Ceiling 2 - Planning Guide for System Integrators PDF
Page 13
... a projector Fig. 19: Simulated view with a yellow dot under "Zones" (Fig. 18). Obstacles on the ceiling, such as quiet reflections in the ceiling. The Control Cockpit software precisely localizes the incoming audio signals and visualizes them with activated Exclusion Zone 2023-01 | v2.0 The TCC2 is... the cooling fan. After activating the Exclusion Zone, the audio signals from this area are obstacles on the ceiling Planning guide for system integrators TeamConnect Ceiling 2 If there are no longer picked up the noise from the active detection zone by specifying the exact ...
... a projector Fig. 19: Simulated view with a yellow dot under "Zones" (Fig. 18). Obstacles on the ceiling, such as quiet reflections in the ceiling. The Control Cockpit software precisely localizes the incoming audio signals and visualizes them with activated Exclusion Zone 2023-01 | v2.0 The TCC2 is... the cooling fan. After activating the Exclusion Zone, the audio signals from this area are obstacles on the ceiling Planning guide for system integrators TeamConnect Ceiling 2 If there are no longer picked up the noise from the active detection zone by specifying the exact ...
TeamConnect Ceiling 2 and biamp TesiraFORTEr AVB VT4
Page 2
.... AN 1255 v1.0 | 2/11 Application Note for TesiraFORTÉ TeamConnect Ceiling 2 System design guide for meeting space about 4.5 m x 8.5 m (15' x 28'). In this system configuration: 1 TeamConnect Ceiling 2 Ceiling microphone array 1 Microsoft Certified Teams Room System 1 TesiraFORTÉ AVB...running Control Cockpit, Tesira Software and Dante Controller * *This document assumes familiarity with these software platforms. It is recommended that a Tesira Certified Programmer is defined as a meeting rooms This application note shows how TeamConnect Ceiling 2, Biamp Tesira hardware...
.... AN 1255 v1.0 | 2/11 Application Note for TesiraFORTÉ TeamConnect Ceiling 2 System design guide for meeting space about 4.5 m x 8.5 m (15' x 28'). In this system configuration: 1 TeamConnect Ceiling 2 Ceiling microphone array 1 Microsoft Certified Teams Room System 1 TesiraFORTÉ AVB...running Control Cockpit, Tesira Software and Dante Controller * *This document assumes familiarity with these software platforms. It is recommended that a Tesira Certified Programmer is defined as a meeting rooms This application note shows how TeamConnect Ceiling 2, Biamp Tesira hardware...
TeamConnect Ceiling 2 and biamp TesiraFORTEr AVB VT4
Page 8
... the TeamConnect Ceiling 2 unit as shown below (using MDNS). AN 1255 v1.0 | 8/11 With the network cable attached to begin setup. Clicking on the unit to be configured from being deterred by noise sources at known locations (e.g. More information can be examined and edited. A PoE/Control connection and the Sennheiser Control Cockpit software is a ceiling...
... the TeamConnect Ceiling 2 unit as shown below (using MDNS). AN 1255 v1.0 | 8/11 With the network cable attached to begin setup. Clicking on the unit to be configured from being deterred by noise sources at known locations (e.g. More information can be examined and edited. A PoE/Control connection and the Sennheiser Control Cockpit software is a ceiling...
TeamConnect Ceiling 2 and biamp TesiraFORTEr AVB VT4
Page 9
... of the AEC reference signal should be routed from the DSP to the TeamConnect Ceiling 2 AEC Ref input via Dante. When this threshold is not active. This AEC reference signal is used inside the control software for the AEC ref signal: Setup a test-call where the far-end...steadily, at any time when the far-end talker is indicated in Sennheiser Control Cockpit by the loudspeakers) to the TeamConnect Ceiling 2's reference-input-channel (1st Dante input-channel), so the beam-steering can be adjusted in Sennheiser Control Cockpit is crucial to adjust the level of the AEC reference...
... of the AEC reference signal should be routed from the DSP to the TeamConnect Ceiling 2 AEC Ref input via Dante. When this threshold is not active. This AEC reference signal is used inside the control software for the AEC ref signal: Setup a test-call where the far-end...steadily, at any time when the far-end talker is indicated in Sennheiser Control Cockpit by the loudspeakers) to the TeamConnect Ceiling 2's reference-input-channel (1st Dante input-channel), so the beam-steering can be adjusted in Sennheiser Control Cockpit is crucial to adjust the level of the AEC reference...
Configuration of 802.1X for TeamConnect Ceiling 2
Page 3
...; SSH keys (pnac_key pair + pnac-ft_key pair) These keys are provided by Sennheiser on the network, the TCC2 will use the Sennheiser Control Cockpit software (www.sennheiser.com/control-cockpit-software). Network connection The first step is mandatory. Once the IP address of the TCC2... the user will publish its hostname and IP address via multicast DNS (mDNS). Configuration of 802.1X TeamConnect Ceiling 2 Prerequisites For the 802.1X configuration of the TeamConnect Ceiling 2 ceiling microphone array (TCC2) some tools are needed files by SCP (see „Configuring 802.1X") 2....
...; SSH keys (pnac_key pair + pnac-ft_key pair) These keys are provided by Sennheiser on the network, the TCC2 will use the Sennheiser Control Cockpit software (www.sennheiser.com/control-cockpit-software). Network connection The first step is mandatory. Once the IP address of the TCC2... the user will publish its hostname and IP address via multicast DNS (mDNS). Configuration of 802.1X TeamConnect Ceiling 2 Prerequisites For the 802.1X configuration of the TeamConnect Ceiling 2 ceiling microphone array (TCC2) some tools are needed files by SCP (see „Configuring 802.1X") 2....
3rd party control of Sennheiser products using media control protocols
Page 7
Media Control Systems 3rd party control of Sennheiser products using media control protocols Ports and protocols Device ADN Digital 6000 evolution wireless G4 TeamConnect Ceiling 2 MobileConnect/CS1 LSP 500 PRO SpeechLine Digital Wireless Ports & Protocol 53248 53249.53250 any unused (1.0.0.2) ...case CU discovery CU monitoring TCP/IP Traffic mDNS Auto setup Multicast / device discovery all IP communication Service software internal communication Service software internal communication SSC Tftp (only temporarily during the firmware update) mDNS via Multicast Ruckus AccessPoint Connection + ...
Media Control Systems 3rd party control of Sennheiser products using media control protocols Ports and protocols Device ADN Digital 6000 evolution wireless G4 TeamConnect Ceiling 2 MobileConnect/CS1 LSP 500 PRO SpeechLine Digital Wireless Ports & Protocol 53248 53249.53250 any unused (1.0.0.2) ...case CU discovery CU monitoring TCP/IP Traffic mDNS Auto setup Multicast / device discovery all IP communication Service software internal communication Service software internal communication SSC Tftp (only temporarily during the firmware update) mDNS via Multicast Ruckus AccessPoint Connection + ...
TeamConnect Ceiling 2 - TruVoicelift. Sennheiser s Interpretation of Voice Lift. PDF
Page 12
...software with just a few clicks. The horizontal angle can define Exclusion Zones in the Control Cockpit. These coverage ranges encompass a complete hemisphere originating from 0° to 360°. This enables you can configure up to 5 Exclusion Zones based on the situation: • If there is initialized, the TeamConnect Ceiling...zone Adjustment of Exclusion Zones, you to quickly and easily define a precise Exclusion Zone. TruVoicelift TeamConnect Ceiling 2 Advanced Exclusion Zones Meetings often suffer from unwanted background noise, for example from air conditioning ...
...software with just a few clicks. The horizontal angle can define Exclusion Zones in the Control Cockpit. These coverage ranges encompass a complete hemisphere originating from 0° to 360°. This enables you can configure up to 5 Exclusion Zones based on the situation: • If there is initialized, the TeamConnect Ceiling...zone Adjustment of Exclusion Zones, you to quickly and easily define a precise Exclusion Zone. TruVoicelift TeamConnect Ceiling 2 Advanced Exclusion Zones Meetings often suffer from unwanted background noise, for example from air conditioning ...
ES1 Ceiling Audio Solution TeamConnect Ceiling 2 and Bose
Page 12
... an exclusion zone, directed toward the front of the room and in these zones (e.g., ceiling-mounted AC vents, projector fans, doors credenzas). TeamConnect Ceiling 2 Setup and Configuration The Sennheiser TCC2 is a ceiling-mounted dynamic beamforming microphone. Note: Refer to 50 by sending command strings over IP from...noise and sounds in the direction of the TCC2 control object and then press Enter. A PoE/Control connection and the Sennheiser Control Cockpit software are required to red. The Source Detection section on the MTR changes the TCC2 LED to begin the setup process. ...
... an exclusion zone, directed toward the front of the room and in these zones (e.g., ceiling-mounted AC vents, projector fans, doors credenzas). TeamConnect Ceiling 2 Setup and Configuration The Sennheiser TCC2 is a ceiling-mounted dynamic beamforming microphone. Note: Refer to 50 by sending command strings over IP from...noise and sounds in the direction of the TCC2 control object and then press Enter. A PoE/Control connection and the Sennheiser Control Cockpit software are required to red. The Source Detection section on the MTR changes the TCC2 LED to begin the setup process. ...
ES1 Ceiling Audio Solution TeamConnect Ceiling 2 and Bose
Page 14
... reduce the output level of the AEC reference signal by a direction of the AEC reference signal is unmuted but remains quiet. In the control software for the AEC, set the output level for the AEC Ref Signal Set up a test call where the far-end presenter is increased steadily..., at a certain point the static status becomes active and the displayed position in Sennheiser Control Cockpit by 15 dB to be heard. Fire Alarm Override Some municipal building codes require that the alarm and any announcements can be tracked...
... reduce the output level of the AEC reference signal by a direction of the AEC reference signal is unmuted but remains quiet. In the control software for the AEC, set the output level for the AEC Ref Signal Set up a test call where the far-end presenter is increased steadily..., at a certain point the static status becomes active and the displayed position in Sennheiser Control Cockpit by 15 dB to be heard. Fire Alarm Override Some municipal building codes require that the alarm and any announcements can be tracked...
Release Notes - TeamConnect Ceiling 2 Firmware 1.8.4
Page 1
... temporarily not visible in the Control Cockpit. The individual LEDs will switch to v.1.4.7 or higher) TeamConnect Ceiling 2 Firmware v1.8.4 | 1/3 TeamConnect Ceiling 2 Release Notes TeamConnect Ceiling 2 Ceiling microphone array Firmware Update • The TeamConnect Ceiling 2 firmware update requires the Sennheiser Control Cockpit software: www.sennheiser.com/control-cockpit-software Firmware version 1.8.4 - Features • Operating system has been updated to the latest patch level •...
... temporarily not visible in the Control Cockpit. The individual LEDs will switch to v.1.4.7 or higher) TeamConnect Ceiling 2 Firmware v1.8.4 | 1/3 TeamConnect Ceiling 2 Release Notes TeamConnect Ceiling 2 Ceiling microphone array Firmware Update • The TeamConnect Ceiling 2 firmware update requires the Sennheiser Control Cockpit software: www.sennheiser.com/control-cockpit-software Firmware version 1.8.4 - Features • Operating system has been updated to the latest patch level •...
Product Specification Sennheiser Control Cockpit
Page 1
...G4 and Digital 6000 portfolio as well as the TeamConnect Ceiling 2. overview of all network-enabled devices at the same time very easy. outstanding usability on events or system warnings • Event log - The software is accessible everywhere in the intranet via web browser...email and SMS notification • Advanced beam configuration for TeamConnect Ceiling 2 with a 3D real-time visualization Sennheiser Control Cockpit is the central software for high level overview and control about all platforms. As a result, the software allows you to manage even huge setups with hundreds of ...
...G4 and Digital 6000 portfolio as well as the TeamConnect Ceiling 2. overview of all network-enabled devices at the same time very easy. outstanding usability on events or system warnings • Event log - The software is accessible everywhere in the intranet via web browser...email and SMS notification • Advanced beam configuration for TeamConnect Ceiling 2 with a 3D real-time visualization Sennheiser Control Cockpit is the central software for high level overview and control about all platforms. As a result, the software allows you to manage even huge setups with hundreds of ...
Product Specification Sennheiser Control Cockpit
Page 2
SOFTWARE SPECIFICATION 2/5 Sennheiser Control Cockpit Control Software WORKFLOWS KEY WORKFLOW AREAS SETUP MONITORING WORKFLOWS Language selection via browser setting or language selector Password settings for secured access to Sennheiser Control Cockpit Adding device automatically (discovery via mDNS) Adding device manually via IP address, IP range or listed in CSV file Configure location ...: Indication of wireless charging process Management and monitoring of SpeechLine Digital Wireless, evolution wireless G3 and G4, Digital 6000 devices as well as TeamConnect Ceiling 2 simultaneously
SOFTWARE SPECIFICATION 2/5 Sennheiser Control Cockpit Control Software WORKFLOWS KEY WORKFLOW AREAS SETUP MONITORING WORKFLOWS Language selection via browser setting or language selector Password settings for secured access to Sennheiser Control Cockpit Adding device automatically (discovery via mDNS) Adding device manually via IP address, IP range or listed in CSV file Configure location ...: Indication of wireless charging process Management and monitoring of SpeechLine Digital Wireless, evolution wireless G3 and G4, Digital 6000 devices as well as TeamConnect Ceiling 2 simultaneously
Product Specification Sennheiser Control Cockpit
Page 3
SOFTWARE SPECIFICATION 3/5 Sennheiser Control Cockpit Control Software WORKFLOWS KEY WORKFLOW AREAS MONITORING CONTROL ASSISTANCE MAINTENANCE WORKFLOWS Messages overview as log of alerts, notifications and events with time stamp, device and location flag...Device List Monitoring of the MobileConnect Manager online status Two-way device identification via button-press on device or remotely via software Full remote access to all hardware settings via software Single or multi device selection to change common properties Location based Mute: Easy un/muting of transmitter groups within definded ...
SOFTWARE SPECIFICATION 3/5 Sennheiser Control Cockpit Control Software WORKFLOWS KEY WORKFLOW AREAS MONITORING CONTROL ASSISTANCE MAINTENANCE WORKFLOWS Messages overview as log of alerts, notifications and events with time stamp, device and location flag...Device List Monitoring of the MobileConnect Manager online status Two-way device identification via button-press on device or remotely via software Full remote access to all hardware settings via software Single or multi device selection to change common properties Location based Mute: Easy un/muting of transmitter groups within definded ...
Product Specification Sennheiser Control Cockpit
Page 4
SOFTWARE SPECIFICATION 4/5 Sennheiser Control Cockpit Control Software SERVER SYSTEM REQUIREMENTS Recommended for Host PC • Intel i5 Dual Core processor or similar • 4 GB RAM • at least... 22 22 Protocol HTTP HTTPS HTTP SCP/SSH SCP/SSH Service Product Web UI Sennheiser Control Cockpit Web UI (optional) Sennheiser Control Cockpit Sennheiser Control Cockpit update service Sennheiser Control Cockpit SCP Firmware update & certificate management TeamConnect Ceiling 2, SpeechLine Digital Wireless Multi-Channel Receiver SCP Firmware update Evolution Wireless Digital EW...
SOFTWARE SPECIFICATION 4/5 Sennheiser Control Cockpit Control Software SERVER SYSTEM REQUIREMENTS Recommended for Host PC • Intel i5 Dual Core processor or similar • 4 GB RAM • at least... 22 22 Protocol HTTP HTTPS HTTP SCP/SSH SCP/SSH Service Product Web UI Sennheiser Control Cockpit Web UI (optional) Sennheiser Control Cockpit Sennheiser Control Cockpit update service Sennheiser Control Cockpit SCP Firmware update & certificate management TeamConnect Ceiling 2, SpeechLine Digital Wireless Multi-Channel Receiver SCP Firmware update Evolution Wireless Digital EW...
Product Specification Sennheiser Control Cockpit
Page 5
... email recipients shall be the Sennheiser Control Cockpit. SOFTWARE SPECIFICATION 5/5 Sennheiser Control Cockpit Control Software ARCHITECT'S SPECIFICATION A software shall enable the user to set up, control and monitor all components of wireless microphone systems like Evolution Wireless Digital, SpeechLine Digital Wireless, evolution wireless G3 & G4, Digital 6000 as well as the TeamConnect Ceiling 2 ceiling microphone array via a network...
... email recipients shall be the Sennheiser Control Cockpit. SOFTWARE SPECIFICATION 5/5 Sennheiser Control Cockpit Control Software ARCHITECT'S SPECIFICATION A software shall enable the user to set up, control and monitor all components of wireless microphone systems like Evolution Wireless Digital, SpeechLine Digital Wireless, evolution wireless G3 & G4, Digital 6000 as well as the TeamConnect Ceiling 2 ceiling microphone array via a network...
Mounting and operating instructions TeamConnect Ceiling 2 PDF
Page 5
...colored, can be configured with manufacturer declarations Accessories SL CM FB Ceiling mounting frame M4x8 SL CM EB US Angle brackets (for 2 ft ceiling grid) Package contents SL CM EB 625 Angle brackets (for 625 mm ceiling grid) 6.4 mm M4x12 Art. no . 508291 Product overview ... DE IT PT ES Package contents • TeamConnect Ceiling 2 • 3-pin Phoenix connector (3.81) • 8 self-adhesive rubber feet • 2 eye bolts (M4x10) • Instruction manual • Supplement sheet with software 28 x KE 10-237 See next page TeamConnect Ceiling 2 | 21 no . 508290 M3x8 Torx10 ...
...colored, can be configured with manufacturer declarations Accessories SL CM FB Ceiling mounting frame M4x8 SL CM EB US Angle brackets (for 2 ft ceiling grid) Package contents SL CM EB 625 Angle brackets (for 625 mm ceiling grid) 6.4 mm M4x12 Art. no . 508291 Product overview ... DE IT PT ES Package contents • TeamConnect Ceiling 2 • 3-pin Phoenix connector (3.81) • 8 self-adhesive rubber feet • 2 eye bolts (M4x10) • Instruction manual • Supplement sheet with software 28 x KE 10-237 See next page TeamConnect Ceiling 2 | 21 no . 508290 M3x8 Torx10 ...
Mounting and operating instructions TeamConnect Ceiling 2 PDF
Page 6
...PoE LALNANodoerrWWiFiFii Controll Cockpit hHoossttPPCC ((oopptt..Cclliieenntt)) MMeeddiaiaCcoonnttrrooll Cclient oOppttioionnaall MMeeddiiaa Ccontrol sSeerrvveerr LALNANodoerrWWiiFFii CCoonnttrrooll CCoocckkppiitt cClileiennttss 22 | TeamConnect Ceiling 2 Ethernet PoE/Ctrl 4 4 Digital audio output 5 Reset button 6 Analog audio output 7 PoE/Ctrl socket...45 socket is used to both power the TeamConnect Ceiling 2 via Power over Ethernet and configure it using the Sennheiser Control Cockpit software (see „Configuring the TeamConnect Ceiling 2" on page 32). Use only shielded ...
...PoE LALNANodoerrWWiFiFii Controll Cockpit hHoossttPPCC ((oopptt..Cclliieenntt)) MMeeddiaiaCcoonnttrrooll Cclient oOppttioionnaall MMeeddiiaa Ccontrol sSeerrvveerr LALNANodoerrWWiiFFii CCoonnttrrooll CCoocckkppiitt cClileiennttss 22 | TeamConnect Ceiling 2 Ethernet PoE/Ctrl 4 4 Digital audio output 5 Reset button 6 Analog audio output 7 PoE/Ctrl socket...45 socket is used to both power the TeamConnect Ceiling 2 via Power over Ethernet and configure it using the Sennheiser Control Cockpit software (see „Configuring the TeamConnect Ceiling 2" on page 32). Use only shielded ...