Snapper CRP21850 Support and Manuals
Get Help and Manuals for this Snapper item
View All Support Options Below
Free Snapper CRP21850 manuals!
Problems with Snapper CRP21850?
Ask a Question
Free Snapper CRP21850 manuals!
Problems with Snapper CRP21850?
Ask a Question
Popular Snapper CRP21850 Manual Pages
Operater's Manual - Page 1
Safety Instructions & Operator's Manual for
21" STEEL DECK WALK MOWERS COMMERCIAL MODELS
SERIES 20
Models
CP215520HV (7800372)
NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to 'Engine Power ...
Operater's Manual - Page 2
...Model Number
Serial Number
Engine
Model Type Trim
It is important that you read and understand these instructions for future reference. This manual contains safety information to the instructions in the Snapper... of established lawns and is a trademark of dependable service. For faster service please have your Snapper product will provide many years of Simplicity Manufacturing, Inc...
Operater's Manual - Page 4
...safely enough to the presence of this manual and on the mower, engine and ...the machine must understand these instructions to the Slope Guide at SNAPPER, McDonough, Georgia 30253. DO...Service
Department at the end of children. Replace if damaged. 9. Phone: (1-800-935-2967). ALLOW only responsible adults & teenagers with engine running . Read, understand, and follow instructions...
Operater's Manual - Page 5
...parts have the dealer install any damage and repair.... Use only genuine SNAPPER replacement parts to prevent accidental starting...Service engine and make certain engine, blade and all times until the blade comes to reduce fire hazard and engine overheating. 3. Replace...change engine governor speed settings or overspeed engine. 8.... instructions for holes and other gas appliance. Replace slider...
Operater's Manual - Page 6
... Cap and Dipstick
B. Rear Height Adjustment Latch (2)
E.
Engine Speed Control
K. Contact your specific model. Fuel Filler Cap
C.
Features and Controls
Features and Controls
IMPORTANT The figures and illustrations in this manual are provided for reference only and may differ from your Snapper dealer if you have questions. Rope Start Handle
H.
F
I .
Front Height Adjustment...
Operater's Manual - Page 9
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
Avoid serious
burns, allow sufficient ...and components are desired, such as side discharging or bagging.
Move the engine speed control to the slowest speed setting. 4. Operation
Operation (Continued)
!
The highest cutting position is Notch 1.
Cutting Height Adjustment
1. Move the ground...
Operater's Manual - Page 10
...adjustments or service
with engine and blade running.
Install the adapter...Installing the Grass Bag Adapter
(Optional Accessory on the inside rear of the deflector slips onto the stud behind the rear of the discharge opening , where the rear of the engine) The slot (D) on Some Models) 1.
WARNING
! Inspect frequently and
replace worn or damaged components immediately.
8
www.snapper...
Operater's Manual - Page 12
...
B
B
A Figure 14: Installing the grass bag
Figure 15: Removing the bag slider
! Grass Catcher bags used on some models. Operation
10
www.snapper.com Disconnect spark plug wire and...Immediately replace worn or damaged catcher bags
with engine and blade running.
WARNING
! DO NOT attempt any maintenance, adjustments or service
with only bags recommended by SNAPPER. Install ...
Operater's Manual - Page 13
...replaced. Introduction
To retain the quality of the drive disc
3.
Maintenance
Maintenance - Contact a local SNAPPER dealer for a particular mower, always mention the model and serial number.
! WARNING
! A
Service - Figure 17: Removing the transmission fill plug Note: Snapper "00" grease (Part...for proper oil specifications, procedures and proper service intervals.
2. ...
Operater's Manual - Page 14
...replaced.
3. On self-propelled models, disconnect the transfer rod clip and remove the ground speed control rod before tipping the mower. WARNING
! Disconnect spark plug wire and secure away from the plug.
2.
Important: Drain the fuel tank before folding the handles. 7. Refer to the engine owner's manual. Engine
Service... time for service instructions.
Do not...snapper.com
Operater's Manual - Page 16
...23). lbs.
2. The cable should slide freely with the clips installed at an angle of blade assembly A
Figure 23: Sharpening the ... side up) (E) Capscrew
7.
Wheel Drive Control Adjustment
(Self-Propelled Models Only)
1. Rehook the upper spring to extend or shorten the spring... grinding wheel at these locations. Maintenance
14
www.snapper.com The upper clip should be 4" above the...
Operater's Manual - Page 20
...
www.snapper.com
Install the 3/8" hex lock nut.
Install the new bearing. 5.
Should these models to the pulley. 2. Note the belt routing (Figure 35). WARNING
! Remove the 3/8" hex lock nut (B, Figure 34), located on
the outside of the right wheel bracket. 3.
Engine Drive Belt Replacement (Stretch Type Belts)
1. DO NOT attempt any maintenance, adjustments or service...
Operater's Manual - Page 22
... Cutter Blade (Air Lift Compatible) Cutter Blade (Mulching) Cutter Blade (Not Air Lift Compatible) Cutter Blade (Ninja - Quad Edge) Wheel Drive Pulley to Transmission Pulley Belt Engine to Drive Disc Belt Cantilever Drive Tire Assembly Rubber Drive Tire Parts Manual for Wear Damage Page 14-17
X
and Replacement
* Change oil every 25 hours when operating...
Operater's Manual - Page 23
... authorized SNAPPER dealer. 2. Make sure dip stick or oil filler cap is wet.
1. Troubleshooting
21 Engine needs choking.
1. Check Engine Manual for Instructions.
3. Fuel shut-off to proper level. 4. Blade control is released or is dry.
4. Spark plug defective or gap set improperly.
4. Blade control should be held
Running
securely against handle at all debris. 5. Service...
Operater's Manual - Page 28
... engine models is labeled in accordance with SAE J1995 (Revision 2002-05).
21" STEEL DECK WALK MOWERS COMMERCIAL MODELS SERIES 20
Product Specifications
Deck ...code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in
Gear 1 - 4 mph
5.5 hp 160 cc 1.5 qt
Common Service Parts
Cutter Blade (Ninja - Due to -engine variability. Snapper...
Snapper CRP21850 Reviews
We have not received any reviews for Snapper yet.