Snapper CP2155HV Support and Manuals
Get Help and Manuals for this Snapper item
This item is in your list!
View All Support Options Below
Free Snapper CP2155HV manuals!
Problems with Snapper CP2155HV?
Ask a Question
Free Snapper CP2155HV manuals!
Problems with Snapper CP2155HV?
Ask a Question
Popular Snapper CP2155HV Manual Pages
Operater's Manual - Page 1
... (I.R. 2/25/2008) TP 100-5363-IR-CW-N Safety Instructions & Operator's Manual for further details. Please refer to 'Engine Power Rating Information' for
21" STEEL DECK WALK MOWERS COMMERCIAL MODELS
SERIES 20
Models
CP215520HV (7800372)
NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower...
Operater's Manual - Page 2
... lawns and is not intended for purchasing this quality-built Snapper product.
Briggs & Stratton Yard Power Products Group Copyright © 2008, Briggs & Stratton Corporation
Milwaukee, WI, USA.
Please mail your product registration card to the instructions in the Snapper brand. For faster service please have your confidence in this equipment. All Rights Reserved. This manual...
Operater's Manual - Page 4
... in this manual. 3. Know how to cool before and while backing. 6. DO NOT refuel the machine indoors. 5. Phone: (1-800-935-2967). Never assume that can result in handling gasoline. Refer to your dealer cannot answer to the Slope Guide at SNAPPER, McDonough, Georgia 30253. Use extra care with the following SAFETY instructions could cause...
Operater's Manual - Page 5
...machine serviced by grounding spark plug next to prevent accidental starting. 12. Use only genuine SNAPPER replacement parts to...settings or overspeed engine. 8. Important Operator Safety Instructions (Continued)
! STOP engine when crossing gravel drives, walks, or roads, and under any reason. 11. DO NOT operate mower while under rotating parts. Inspect the mower for any damage and repair...
Operater's Manual - Page 8
... release the blade control.
Handle Height Adjustment
The height of the mower by releasing the wheel drive control.
2.
B B
Figure 4: Starting the mower
Propelling the Mower
1. Refer to the desired speed position.
3. Move the ground ..., adjustments or service
with engine and blade running. STOP engine and blade.
Operation
Figure 5: Mower drive controls 6
www.snapper.com
Operater's Manual - Page 9
...) position. 3.
Stop engine and mower blade by releasing the blade
control before adjusting cutting height. A Figure 9: Removing the recycling cover
7 DO NOT attempt any maintenance, adjustments or service
with engine and blade running. Avoid serious
burns, allow sufficient time for all wheels in
Figure 8: Cutting height settings (approximate)
!
Set all wheels at all times...
Operater's Manual - Page 12
...the mower handle...models.
Engine and components are subject to cool. A
B
B
A Figure 14: Installing the grass bag
Figure 15: Removing the bag slider
! DO NOT attempt any maintenance, adjustments or service
with only bags recommended by SNAPPER. WARNING
! Install...SNAPPER products are made
of the bag (B).
3.
Immediately replace worn or damaged catcher bags
with engine and ...
Operater's Manual - Page 13
... the Engine Manual for all the oil to drain the oil, as specified in Transmission
1. Allow sufficient time for a particular mower, always mention the model and serial...mower, use genuine SNAPPER replacement parts only. For the correct part or information for all components to be replaced. Remove the transmission fill plug (A, Figure 17). Contact a local SNAPPER dealer for parts and service...
Operater's Manual - Page 14
... are HOT. Drain the fuel from weather.
Engine
Service the engine according to cool. On self-propelled models, disconnect the transfer rod clip and remove the ground speed control rod before operating the mower. Maintenance
12
www.snapper.com
Avoid serious
burns, allow sufficient time for service instructions. Tilt the mower up on its rear wheels and thoroughly
clean...
Operater's Manual - Page 16
... or service
with the clips installed at these...Check torque of blade assembly A
Figure 23: Sharpening the mower blade
5. Recommended torque should be 4" above the lower knob...) between the inside of the spring hook (E) and the inside of blade.
6. Maintenance
14
www.snapper.com G D F
A B
C E
Blade Sharpening (Continued)
4. Note the correct assembly order:...Self-Propelled Models Only)
1.
Operater's Manual - Page 17
... problems, service as follows: 1.
Wipe away any maintenance, adjustments or service
with a clean cloth. 2. Driven disc rubber is still slipping, adjust the driven disc as follows: 1. Rinse components with a clean cloth. Dry components with clean water. 4. Driven and Drive Disc Service
If the mower does not propel itself properly, check for all components to the Troubleshooting...
Operater's Manual - Page 20
... 3/8" hex lock nut. Should these models to the drive disc (C). Engine Drive Belt Replacement (Stretch Type Belts)
1.
Avoid serious
burns, allow sufficient time for all components to the pulley. 2. Hold the hex shaft with an adjustable wrench held next
to cool. Install the new bearing. 5. Belt Service
On self-propelled mowers, the engine belt (A, Figure 35) transmits...
Operater's Manual - Page 22
...present.
Maintenance/Replacement Parts
Engine Speed ...Manual
Drive Belts
Check for Wear and Tension
Page 12, 18
Mower Blade Check for wear, Damage Page 13
X
& Replacement
X**
X
X
X
Mower Deck
Clean Debris Accumulation
Page 5
X
Transmission
Check Grease Level
Page 11
X
X
Grease
Periodic Grease Check
Page 11
X
Drive Disc Check for 21" Steel Deck Commercial Walk Behind Mower...
Operater's Manual - Page 23
... or gap set improperly.
4. Water, debris or stale fuel in place. Loose or missing air lift (if equipped).
3. Drive belt requires replacement.
3. Cutting height too low or high.
2. Grass is dry.
4. Clean deck.
6. Improper blade installed on deck.
6. Troubleshooting
21 Check Engine Manual for Instructions.
3. Excessive Vibration
1. Service mower blade. 2.
Blade...
Operater's Manual - Page 28
... is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). 21" STEEL DECK WALK MOWERS COMMERCIAL MODELS SERIES 20
Product Specifications
Deck Size Height of Cut Transmission Type Ground Speed Engine...
Snapper CP2155HV Reviews
Do you have an experience with the Snapper CP2155HV that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Snapper yet.
Earn 750 points for your review!