TASCAM DCP CONNECT Support and Manuals
Get Help and Manuals for this TASCAM item
View All Support Options Below
Free TASCAM DCP CONNECT manuals!
Problems with TASCAM DCP CONNECT?
Ask a Question
Free TASCAM DCP CONNECT manuals!
Problems with TASCAM DCP CONNECT?
Ask a Question
Popular TASCAM DCP CONNECT Manual Pages
wner s Manual - Page 2
... by end users can be customized By assigning only the necessary functions, unintended operation mistakes and trouble by system integrators and managers with a simple and easy to use it supports a wide range of functions. TASCAM EZ CONNECT 28 TASCAM EZ CONNECT can be connected with the following Dante Compact Processor Series devices 28 Using...
wner s Manual - Page 3
pp Messages that you always use the software. ATTENTION Failure to follow these instructions could result in damage to use the latest firmware for example. VCAUTION Failure to follow these instructions could result in injury. pp The App Store is a service mark of Cisco Systems, Inc. pp IOS is a registered trademark of Apple Inc.
in...
wner s Manual - Page 7
... to connect to a Wi-Fi access point that you
might not be protected. (see "SETTINGS page" on the network, the following Dante Compact Processor Series devices.
1. Set the password for the Dante Compact Processor Series device. 2 - TASCAM DCP CONNECT
TASCAM DSP CONNECT can be possible depending on . If connections are connected by Wi-Fi or...
wner s Manual - Page 9
... TASCAM DCP CONNECT and used .
DEMO MODE Tap this indicator to open that are on the SETTINGS screen and detection is input and login succeeds.
Click this menu item, to be checked. The maximum number of the device will become possible if the password is not possible using the above Manual login method succeeds, "MANUAL...
wner s Manual - Page 10
2 -
The selection button for the UNIT NAME item on the SETTINGS page. (see "SETTINGS page" on page 24)
4 MODEL This shows the model of the window or tablet display.
Use this page to make TASCAM EZ CONNECT settings. This is not shown when the mode switch (2) is being operated, the INPUT button will not be used to...
wner s Manual - Page 11
...UPDATE button will not be tapped after a name for a new preset to open the following settings are saved in the preset list, putting checks (4) into their selection boxes (8). TASCAM...4D is not supported in these boxes to export the presets to files or to update the preset list... in the "exported files" folder on the network setup and Wi-Fi connection conditions.
ooINPUT page ooMIXER page...
wner s Manual - Page 13
... setup and Wi-Fi connection conditions.
1 Mic/line input setting status This shows the MIC/LINE selection button setting on the Additional Input Settings screen.
2 Phantom power supply setting status... automatic level control function is reversed.
8 COMPRESSOR setting status This shows the COMPRESSOR on/off setting status.
2 - TASCAM DCP CONNECT
INPUT page
The INPUT page shows information...
wner s Manual - Page 14
TASCAM DCP CONNECT
t Mute button Tap the button to unmute that channel. The button appears unlit when muted. (Default: ...might damage this to change the phase of the signals on the network setup and Wi-Fi connection conditions.
1 Input channel
This shows the channel number for the open the Additional Input Settings screen for the channel. Doing so could damage the equipment or harm ...
wner s Manual - Page 17
...activated. (Default: unlit)
NOTE
All channels can be set it with each
Dante Compact Processor Series model differs depending on the network setup and Wi-Fi connection conditions. 2 -
ii The ...channel name editing pop-up screen. TASCAM DCP CONNECT
MIXER page
Settings for each mixer channel on the MIXER page and settings on the Additional Input Settings screen in the fader level display ...
wner s Manual - Page 18
... Use this area to adjust in the MIX Name field.
TASCAM DCP CONNECT
0 MIX master fader Use to adjust the level sent to 0 dB. Tap this to close the Additional Mixer Settings screen and return to the MIXER page.
4 Ducking function settings area This sets the ducking function for the open Mix.
6 MIX master...
wner s Manual - Page 19
... level will be measured by the ANC function. When on the network setup and Wi-Fi connection conditions.
4 ANC function illustration This shows the level change of the ANC function. Settings: -20 dB - 0 dB (-10 dB default, 1 dB increments)
7 RATIO This sets the gain compression ratio of the ANC function.
5 MAX GAIN This...
wner s Manual - Page 20
... Channel Label that can be output from the OUTPUT page and the output names set to open a Dante channel name editing pop-up screen.
NOTE
ii A single input source can be seen with each
Dante Compact Processor Series model differs depending on page 24.
1 Input source names and level meters This shows...
wner s Manual - Page 24
....
Tap again to open a setting value list.
24 For details, see the Dante Controller Operation Manual.
To change the login screen password, tap the CHANGE button to make...new. TASCAM DCP CONNECT
SETTINGS page
The SETTINGS page shows the status of the connected Dante Compact Processor Series device.
5 UNIT SEARCH Tap the IDENTIFY button to make related settings.
2 FIRMWARE VERSION...
wner s Manual - Page 25
... the settings.
ii Importing preset files might not be entered manually. Tap...TASCAM DCP CONNECT
9 NETWORK SETTING Tap the CHANGE button to confirm the edited preset file name.
5 DELETE button This deletes the selected preset file. ii When an AE-4D is not supported in the Android and iOS versions. EXPORTED FILES screen
Use this state, tap the RENAME button to open the GPI SETTING...
wner s Manual - Page 33
... multiple Dante Compact Processor Series devices the same. 2 Make the area passwords set the same number source selection
for the VOLUME setting with multiple Dante Compact Processor Series devices. 4 - TASCAM EZ CONNECT setting example
Operating multiple Dante Compact Processor Series devices with TASCAM EZ CONNECT
Multiple Dante Compact Processor Series devices can operate MX-8A units...
TASCAM DCP CONNECT Reviews
We have not received any reviews for TASCAM yet.