Troy-Bilt CS 4325 Support and Manuals
Get Help and Manuals for this Troy-Bilt item
View All Support Options Below
Free Troy-Bilt CS 4325 manuals!
Problems with Troy-Bilt CS 4325?
Ask a Question
Free Troy-Bilt CS 4325 manuals!
Problems with Troy-Bilt CS 4325?
Ask a Question
Most Recent Troy-Bilt CS 4325 Questions
Cs4325 B&s Carb Removal
I need to remove the carb to clean it. Unit won't start but runs with starting fluid spray
I need to remove the carb to clean it. Unit won't start but runs with starting fluid spray
(Posted by 1kat1bird 1 year ago)
I'm Trying To Change The Engine On My Cs4325
How do I remove the impellor so I can remove the engine mounting bolts??
How do I remove the impellor so I can remove the engine mounting bolts??
(Posted by EPJDDS 9 years ago)
Troy Cs 4325 Oil Change Procedure
How do I change the oil in my chipper shredder
How do I change the oil in my chipper shredder
(Posted by gbaker1951 9 years ago)
Popular Troy-Bilt CS 4325 Manual Pages
Operation Manual - Page 1
... MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-08123 April 23, 2012
Printed In USA
TROY-BILT LLC, P.O. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Model Series CS4265 Shown
Chipper Shredder -
Operation Manual - Page 2
...
2 Review this manual may cover a range of Contents
Safe Operation Practices 3 Assembly & Set-Up 7 Controls & Features 8 Operation 9 Maintenance & Adjustment 11
Service 13 Troubleshooting 15 Replacement Parts 16 Warranty 18 Spanish 19
Record Product Information
Before setting up , operate and maintain your machine, for purchasing a Troy-Bilt Chipper Shredder. Troy-Bilt reserves...
Operation Manual - Page 4
... kickback of material through the shredder hopper, use a small diameter stick. Do not operate this manual. Contact Customer Support for damage. Wash your clothes which are not covered in this machine on a truck or trailer bed with the rotating impeller can amputate fingers, hands, and feet.
2.
Repair or replace any loose parts and tighten to keep machine...
Operation Manual - Page 5
... or replace safety and instruction labels, as a water
brushcovered or grass-covered land unless the
heater, furnace, clothes dryer, etc. Follow this manual for safe loading, unloading, transporting, and storage of seven (7) years,
A spark arrestor for proper instructions on or near any unimproved forest-covered,
there is available through your nearest engine authorized service dealer...
Operation Manual - Page 7
... on the draw-strap until the bag is shipped without gasoline or oil in a raised position. See Figure 3-2. 2. Chipper Chute (Model Series CS4325 Only)
For shipping reasons, the unit is crated with engine running or until it downward, proceed as instructed in property damage or serious injury to the separate engine owner's manual for the first time out of...
Operation Manual - Page 8
...
Chute Deflector
Lock Rod
Model Series CS4325 Shown
Chipper Chute
Branches up to 1/2-inch in the raised position. Recoil Starter
The recoil starter is discharged from the machine's reduction chamber through the chute deflector.
8
It is located on the top of the engine controls. Handle
Use the handle when manually transporting the chipper shredder. Engine Controls
See the separate...
Operation Manual - Page 9
... lever to STOP position (if equipped) or push rocker switch to your unit for the correct starting instructions may not. CAUTION: Never stop the engine by moving the choke lever into the eyes, which can result in a poorly ventilated area.
Starting Engine
IMPORTANT: Because this manual covers several different model units, different starting procedure. Open fuel...
Operation Manual - Page 10
...
opening.
Refer to due so may result in the hopper. Failure to the "Set-Up & Adjustments" section of this manual. Stop engine. 2. Figure 5-3 3. Twigs longer than two (2) inches (Model Series CS4265) or three (3) inches (model series CS4325) into the chipper chute.
Use your unit's chipper blades, flails or impeller. Shredding
Yard waste such as leaves and pine needles can...
Operation Manual - Page 11
...section of the Engine Operator's manual packed with your unit. Check engine manual for engine lubrication instructions. WARNING: Always stop engine, disconnect spark plug, and ground against engine before each use .
• Wash bag periodically with water.
Keep the top of the engine clean to operator abuse or negligence.
Equipment Care
• Clean the chipper shredder thoroughly after...
Operation Manual - Page 12
... engine has been running.
See Figure 6-1.
Remove the two wing knobs on the starter rope two-to-three times to protect your hands if working near the muffler. Cleaning The Reduction Chamber
3. If the reduction chamber becomes clogged with the clevis pin and hairpin clip removed earlier. If attached, remove debris bag. chipper shredder...
Operation Manual - Page 13
... angle of
the impeller. C
B
A
Model Series CS 4325 Shown
Figure 7-1
4. Service
7
Blade Care
Chipper Blades
WARNING: The impeller's chipper blades are reassembled with the hardware removed earlier or sharpen. Wear leather work gloves to the impeller housing. Remove the blade by removing the two hex bolts and saddle washers which secure the hopper support bracket to protect your...
Operation Manual - Page 14
... springs, bearings, and cables. Service Remove six flange nuts which secure the shredder blade to between 45 ft.-lbs and 58 ft.-lbs and the two out
bolts to the
impeller. See Figure 7-3A. Hold the Allen wrench stationary and rotate the box (or socket) wrench to engine manual for a short time before shutting...
Operation Manual - Page 15
... switch button is full. 1. Loose parts or damaged impeller.
1. Vacuum bag is not fully
depressed.
1. Turn on CHOKE (if equipped). 3. Make certain the bag is correctly secured,
and the bag/chute switch button is fully depressed.
1. Always run engine at full throttle. 4. See authorized service dealer.
1. See authorized service dealer.
1. Replace chipper blade or see your...
Operation Manual - Page 16
... downloads are also available free of charge at www.troybilt.com.
16 Replacement Parts
Component
9
Part Number and Description
942-04050
Shredder Blade
942-0544B
Chipper Blade
719-04308
Flail Blade (3 total)
634-04627
10 x 4.0 Pneumatic Wheel with Bearings
Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).
Operation Manual - Page 18
... respect to new merchandise purchased and used in the United States and/or its territories and possessions (either entity respectively, "TroyBilt").
The engine or component parts thereof.
Troy-Bilt does not warrant this warranty.
Troy-Bilt shall not be free from the date of the product shall void this product for terms and conditions.
Phone 1-800-668...
Troy-Bilt CS 4325 Reviews
We have not received any reviews for Troy-Bilt yet.