Troy-Bilt Pro-Line CRT Support and Manuals
Get Help and Manuals for this Troy-Bilt item
View All Support Options Below
Free Troy-Bilt Pro-Line CRT manuals!
Problems with Troy-Bilt Pro-Line CRT?
Ask a Question
Free Troy-Bilt Pro-Line CRT manuals!
Problems with Troy-Bilt Pro-Line CRT?
Ask a Question
Most Recent Troy-Bilt Pro-Line CRT Questions
Proline Frt Tiller Return Spring Assembly
I have replaced the drive belts on my tiller..........I can't figure out where the return spring on ...
I have replaced the drive belts on my tiller..........I can't figure out where the return spring on ...
(Posted by melnichukjohn 2 years ago)
Proline Crt Want Stay Running
It cranks right up, although its harder to pull than it use to be but as soon as it meets any resist...
It cranks right up, although its harder to pull than it use to be but as soon as it meets any resist...
(Posted by janmills64 9 years ago)
Popular Troy-Bilt Pro-Line CRT Manual Pages
Operation Manual - Page 1
Printed In USA
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-07548 (December 13, 2011)
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Bronco, Super Bronco & Pro-Line CRT Tillers
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ...
Operation Manual - Page 2
...change product specifications, designs and equipment without notice and without first contacting the Customer Support Department. You can be aware that this Operator's Manual may not be sure that you for purchasing a Troy-Bilt Tiller.
If applicable, the power testing information used to establish the power rating of the tine shield. We want to Maintenance and Parts Installation Videos...
Operation Manual - Page 9
.... 3-5. Use the handlebar to roll the tiller to between 15 and 20 PSI.
Z-Connector
Reverse Clutch Cable (If so equipped)
1. Z-Connector
Cable Bracket
Cable Bracket
Figure 3-6 2. See Fig. 3-7. Service the engine with gasoline and oil as instructed in the Engine Operator's Manual packed separately with a tire gauge. Section 3 - Assembly & Set-Up
9 The wheel should now...
Operation Manual - Page 12
...! On models with one side of
the ground and the engine and tines are used on the handlebar (one hand, yet keep your arm loose). Clearing the Tines
The tines have a self-clearing action which eliminates most easily). Do not till near buried electric cables, telephone lines, pipes or hoses.
• This is a CRT (counter-rotating tine) tiller...
Operation Manual - Page 24
... WARRANTY: This limited warranty gives you specific legal rights, and you and your area:
In the U.S.A.
Phone: 1-866-840-6483, 1-330-558-7220 MTD Canada Limited - Belts are warranted to be greater than an authorized service dealer. Attachments include, but are not genuine Troy-Bilt parts. e.
The provisions as set forth above as mentioned above exclusions...
Service Manual - Page 1
Product Training and Education Department
FORM NUMBER 769-01529 11/2004 Service Manual
Small Frame Troy-Bilt Tillers
MTD Products LLC -
Service Manual - Page 5
...plug, and ground it to the Engine Owner's Manual for -
ward clutch spring with the Troy-Bilt Factory School. Record the forward clutch spring measurement ... FORWARD CLUTCH CABLE ADJUSTMENT:
2.1. Troy-Bilt Small Frame Tillers
Troy-Bilt Small Frame Tillers
TUFFY TILLER
ABOUT THIS SECTION:
NOTE: This section covers the Tuffy rear tine tiller, model 21A-630B063 with Serial Number 1B212G80447...
Service Manual - Page 12
...is resting on the tines and not on the trailing shield.
Hair Pin
Clevis Pin
Figure 6.15
6.16. Raise the front of the tiller up until the ...tine hood to allow the depth bar's spiral pin to pass through. Remove both wheel assemblies.
8
Remove both hair pins and clevis pins securing the wheel assemblies onto the wheel shaft using needle nose pliers. Troy-Bilt Small Frame Tillers...
Service Manual - Page 13
... 1/2" socket. See Figure 6.21. Lower the front of the unit until the front support can be stabilized before removing the transmission. See Figure 6.17. Self-Tapping Screws
Cable ...
6.21. Remove both sets of the unit and raise it up until the pulley/belt guard is setting on the ground.
9
Pivot the forward idler lever inward. 6.19.
Troy-Bilt Small Frame Tillers
6.20. Figure 6.21...
Service Manual - Page 14
...front assembly.
See Figure 6.29. Remove the transmission assembly from the forward idler lever. Set the unit on the floor. See Figure 6.24.
See Figure 6.28. Pivot the ... 6.26
NOTE: A small pry bar can be used for assistance, if necessary. 6.27.
Troy-Bilt Small Frame Tillers
6.24.
Remove the hex screw and belleville washer securing the transmission pulley to the drive shaft...
Service Manual - Page 15
... of the transmission up and set it on a 2" x 4" block. Raise the rear of the tine assemblies for correct installation. See Figure 6.31.
Rotate the transmission horizontally 180°. Remove the hex screws and lock nuts securing the right and left tine assemblies using a 1/2" socket.
Transmission Pulley Key
Belleville
Troy-Bilt Small Frame Tillers
6.33. Hex Screw & Lock Nut...
Service Manual - Page 21
...Rotate the wheel shaft worm gear until the HiPro key slides into the housing until the Hi-Pro key contacts the wheel shaft worm gear.
7.41. NOTE: Two paper clips with small ...Shim Removal Tools
7.35. Slide the wheel shaft back into the key way.
17 See Image Below
Troy-Bilt Small Frame Tillers
7.38. See Figure 7.35.
See Image Below. Record the thicknesses of wood and a large ...
Service Manual - Page 22
...the bronze wheel shaft bushing out of wood and a large hammer. Wheel Shaft
Wheel Shaft Worm Gear Hi-Pro Key
Bronze Bushings
Internal Shims External Shims Retaining Rings
Oil Seals Figure 7.46
18 See Figure 7.45. Figure... with the other. See Figure 7.42.
7.45.
Remove the Hi-Pro key from the right side of the transmission housing. See Figure 7.46. Troy-Bilt Small Frame Tillers
7.42.
Service Manual - Page 25
...
Race Tapered Roller
Bearing
Drive Shaft Assembly
Figure 7.61
8. Locate both hex flange screws that is
lined with a protective material.
Make certain all the drive shaft components are accounted for wear or damage. Troy-Bilt Small Frame Tillers
8.3. Set the transmission housing in a vice that were securing the left and right hood brackets to the...
Service Manual - Page 30
... using a soft mallet. See Figure 8.35.
8.41. See Figure 8.37. Troy-Bilt Small Frame Tillers
8.35.
Drive the Hi-Pro key into the transmission housing until it is flush with the outside of the wheel shaft bronze bushing that has been installed.
8.37. Hi-Pro Key
Wheel Shaft
Figure 8.35
8.36. Drive Shaft
Wheel Shaft Worm...
Troy-Bilt Pro-Line CRT Reviews
We have not received any reviews for Troy-Bilt yet.