Operation Manual
Page 1
Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-08123 April 23, 2012 Model Series CS4265 & CS4325 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Model Series CS4265 Shown Chipper Shredder - FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
Printed In USA TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-08123 April 23, 2012 Model Series CS4265 & CS4325 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Model Series CS4265 Shown Chipper Shredder - FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
Operation Manual
Page 7
... information. 1. WARNING: Never fill fuel tank indoors with gasoline as instructed in the raised position. Gasoline is crated with the chipper chute in the accompanying engine manual BEFORE operating your chipper shredder. Chipper Chute (Model Series CS4325 Only) For shipping reasons, the unit is extremely flammable and the vapors are completely covered. 3. See Figure 3-1. Assembly & Set...
... information. 1. WARNING: Never fill fuel tank indoors with gasoline as instructed in the raised position. Gasoline is crated with the chipper chute in the accompanying engine manual BEFORE operating your chipper shredder. Chipper Chute (Model Series CS4325 Only) For shipping reasons, the unit is extremely flammable and the vapors are completely covered. 3. See Figure 3-1. Assembly & Set...
Operation Manual
Page 8
... on the engine. Handle Use the handle when manually transporting the chipper shredder. Recoil Starter The recoil starter is used to release or lock the chipper chute in a lowered position for chipping. Hopper Leaves, twigs, and branches up to two inches (model series CS4265) or three inches (model series CS4325) in diameter may be fed into the...
... on the engine. Handle Use the handle when manually transporting the chipper shredder. Recoil Starter The recoil starter is used to release or lock the chipper chute in a lowered position for chipping. Hopper Leaves, twigs, and branches up to two inches (model series CS4265) or three inches (model series CS4325) in diameter may be fed into the...
Operation Manual
Page 10
... vines do not shred well and tend to two inches (model series CS4265) or three inches (model series CS4325) in the hopper. Stop engine. 2. Observe the following guidelines when shredding yard debris: • Never attempt to the hopper. Chipping WARNING: Never operate the chipper shredder without chipper chute lowered into the operating position. • Never feed more...
... vines do not shred well and tend to two inches (model series CS4265) or three inches (model series CS4325) in the hopper. Stop engine. 2. Observe the following guidelines when shredding yard debris: • Never attempt to the hopper. Chipping WARNING: Never operate the chipper shredder without chipper chute lowered into the operating position. • Never feed more...
Operation Manual
Page 13
... equal amount from the frame by hand until one of the two chipper blades is sharp. Remove the chipper chute support brace from each blade. 8. Follow the original angle of the impeller. See Figure 7-2. C B A Model Series CS 4325 Shown Figure 7-1 4. Retain the hardware. 3. Pivot the shredder screen upward as instructed under the heading Cleaning the Reduction Chamber...
... equal amount from the frame by hand until one of the two chipper blades is sharp. Remove the chipper chute support brace from each blade. 8. Follow the original angle of the impeller. See Figure 7-2. C B A Model Series CS 4325 Shown Figure 7-1 4. Retain the hardware. 3. Pivot the shredder screen upward as instructed under the heading Cleaning the Reduction Chamber...