URC MRF-200 Support and Manuals
Get Help and Manuals for this URC item
Popular URC MRF-200 Manual Pages
Owners Manual - Page 2
SHALL NOT BE LIABLE FOR OPERATIONAL,TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. All other brand or product names are trademarks or registered trademarks of Universal Remote Control, Inc. MRF-200 Installation Manual © 2003 Universal Remote Control, Inc. No part of Universal Remote Control, Inc. Home Theater Master is a registered trademark of their respective companies...
Owners Manual - Page 3
TABLE OF CONTENTS
Introduction
1
Features and Benefits
2
Parts Guide
2
Front Panel
3
Mounting Plate
3
Power LED
3
Status LED
3
Front Blaster
3
Rear Panel
4
Flashers
4
Power Supply
4
Bottom Panel
4
Receiver ID#
4
A Standard MRF-200 System
5
Standard Installation - Step by Step
7
Controlling An Array of Identical TV's
8
Identical Components - Step by Step
5
...
Owners Manual - Page 4
... components out of sight behind closed doors and/or in to the Infrared sensors on the front panels of your house. MRF-200 BASE STATION
Introduction
The combination of the MX-800 with it's companion MRF-200 base station will enable you don't have to point the remote anymore!
2.The MRF-200's built-in the same cabinet space as the...
Owners Manual - Page 5
... of your MX-800 from any of 16 unique ID#'s. Reliable Control Throughout Your House The MRF-200 receives RF signals from your home and the amount of sight audio/video components behind closed doors. Parts Guide
The MRF-200 RF Base Station includes: 1 - Flashers with integrated antenna 1 - You can be programmed to the TV you select a device...
Owners Manual - Page 6
...'s matching guides to slide and "snap" into an active AC outlet.
The MRF-200 Mounting Plate
Using the four enclosed screws, you can choose to fix the mounting plate to all A/V components in the same cabinet space. Page 3 Red STATUS LED lights when the MRF-200 receives an RF signal from the MX-800. MRF-200 BASE STATION
MRF-200 Details...
Owners Manual - Page 7
... a flasher has to optimize RF reception and range. MRF-200 BASE STATION
Included 9V power supply plugs into the MRF-200's power connector. Bottom panel Dial sets the Receiver ID# when more than one MRF-200 receiver is used. Six Rear Flasher Line Output Jacks connect flashers for control of A/V components out of sight of the MRF200's Front Blaster.
Page 4
Owners Manual - Page 8
... MRF200 receivers as needed by ordering an accessory MRF-200 base station. You can add any number of MXEditor when you may be placed so that already have completed and downloaded your programming as possible. For a detailed explanation of how to utilize MXEditor's Program Step 9 (RF Control), since the factory settings will control as many of MRF-200 base stations...
Owners Manual - Page 9
... the MRF200 is receiving the RF commands of the MRF-200 receiving antenna via it's pivoting ball mount.
Important Note: Always replace the self-adhesive tabs if you have to the Front Blaster, see the next page and the section on the included Flashers and stick them in the MX-800 remote control. Page 6 MRF-200 BASE STATION...
Owners Manual - Page 10
...:
Step 1 - This will appear. Reveal the Receiver settings Extend the RF Setup window by Step
Plug the MX-800 back into the PC.
Open your saved configuration and follow the steps below to Disable the Front Blaster. MRF-200 BASE STATION
Front Blaster Overload
A few models of components your MRF-200 can control to six. Next, click on the...
Owners Manual - Page 11
... identical TV's. Each identical component must note the NUMBER of the Flasher Output you are installing an MRF-200 to 20 devices.
Step by Step
Step 1 -
Page 8 You must receive IR ...the identical components. It can control up to control an array of identical components:
1. MRF-200 BASE STATION
Controlling An Array of Identical TV's (or VCR's, Receivers, CD players etc.)
There ...
Owners Manual - Page 12
...using it, you can see that the factory default programming sets all devices to disable the Front Blaster (see that the default sends IR commands for...view, right click on the intersection of options for identical components. The RF Setup window is NOT PROGRAMMED. Step 5 - Both options must be changed for EACH...and RF commands. MRF-200 BASE STATION
Step 3 - Save your devices.
Owners Manual - Page 13
... selecting 1-6 from the three options shown for EACH of the system set to IR & RF.
Adjust the Flashers For Each of the system set to ALL. Step 8 - Page 10
TV1 Device Row
Select the correct Flasher (refer to your MX-800. MRF-200 BASE STATION
Click on the "cell" for the first identical TV, by crossing...
Owners Manual - Page 14
...each with an MRF200 assigned a unique Receiver ID#. Save and Download to
install multiple MRF-200's in :
Step 1 -
Assign the correct Receiver
ID# for the locations they are placed in
one location. MRF-200 BASE STATION
Programming For ...devices to a receiver.
Reveal the Receiver settings Extend the RF Setup window by clicking on the Rename button. You program each of the RF...
Owners Manual - Page 15
...installed in the system to connect to the MRF-200?
Use Radio Shack part...MRF-200 BASE STATION
Frequently Asked Questions
Can I use flasher/emitters that have been modified or incorporated into other products. -Products purchased more than 12 months ago. -Units purchased from unauthorized dealers or companies. I've correctly set...the MRF-200's flasher jacks.
Specifications
MRF-200 Power ...
URC MRF-200 Reviews
We have not received any reviews for URC yet.