Installation Instructions
Page 3
...at least 4 ft. (1.22 m) long. Location Requirements Adjustable wrench that all parts are included. INSTALLATION REQUIREMENTS Tools and Parts Parts supplied: Gather the required tools and parts before purchasing parts. The cord should contain: ■■ A UL listed 30-amp power supply... for use with any tools listed here. For further information, please reference the "Assistance or Service" section of the Dryer User Instructions. Parts needed : Flat-blade screwdriver #2 Phillips screwdriver Wire stripper (direct wire installations) Tin snips (new vent installations) 1/4" ...
...at least 4 ft. (1.22 m) long. Location Requirements Adjustable wrench that all parts are included. INSTALLATION REQUIREMENTS Tools and Parts Parts supplied: Gather the required tools and parts before purchasing parts. The cord should contain: ■■ A UL listed 30-amp power supply... for use with any tools listed here. For further information, please reference the "Assistance or Service" section of the Dryer User Instructions. Parts needed : Flat-blade screwdriver #2 Phillips screwdriver Wire stripper (direct wire installations) Tin snips (new vent installations) 1/4" ...
Installation Instructions
Page 4
...formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). ■■ Metal exhaust system hardware, which is recommended to introduce outside air into the dryer. The dryer must conform to open fully. Contact your dealer. ■■ Special provisions ...spacing allowed. ■■ Additional spacing should be sure that the ground path is greater than 1" [25 mm], install Extended Dryer Feet Kit, Part Number 279810.) If not level, clothes may not tumble properly and automatic sensor cycles may not operate correctly. Do not operate ...
...formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). ■■ Metal exhaust system hardware, which is recommended to introduce outside air into the dryer. The dryer must conform to open fully. Contact your dealer. ■■ Special provisions ...spacing allowed. ■■ Additional spacing should be sure that the ground path is greater than 1" [25 mm], install Extended Dryer Feet Kit, Part Number 279810.) If not level, clothes may not tumble properly and automatic sensor cycles may not operate correctly. Do not operate ...
Installation Instructions
Page 14
... kit). Left or right side exhaust installation C. In Canada, call 1-800-901-2042, or visit us at www.applianceaccessories.com. Part Number Descriptions 8171587RP 0-5" Metal vent periscope 4396037RP 0"-18" Metal vent periscope 4396011RP 18" - 29" Metal vent periscope 4396014 29"...-6777 or visit us at www.whirlpoolparts.ca. C D E A F G Over-The-Top installation (also available with clamps 4396004 Dryer offset elbow 4396005 Wall offset elbow 4396006RW DuraSafe™ close clearance alternate installations are available for purchase. Other installations are shown. Elbow C....
... kit). Left or right side exhaust installation C. In Canada, call 1-800-901-2042, or visit us at www.applianceaccessories.com. Part Number Descriptions 8171587RP 0-5" Metal vent periscope 4396037RP 0"-18" Metal vent periscope 4396011RP 18" - 29" Metal vent periscope 4396014 29"...-6777 or visit us at www.whirlpoolparts.ca. C D E A F G Over-The-Top installation (also available with clamps 4396004 Dryer offset elbow 4396005 Wall offset elbow 4396006RW DuraSafe™ close clearance alternate installations are available for purchase. Other installations are shown. Elbow C....
Installation Instructions
Page 16
...tape remaining on . ■■ Household fuse is intact and tight, or circuit breaker has not tripped. ■■ Dryer door is not crushed or kinked. Once legs are level, make sure all parts are snug against the ground before tightening them. q Dispose of your Use and Care Guide. q Check... and start , check the following : ■■ There may notice an odor when the dryer is an extra part, go away. 16 Check that dryer is in place, remove corner posts and cardboard from under the dryer. q Check that both fuses are set in your tools. q Remove film on console and ...
...tape remaining on . ■■ Household fuse is intact and tight, or circuit breaker has not tripped. ■■ Dryer door is not crushed or kinked. Once legs are level, make sure all parts are snug against the ground before tightening them. q Dispose of your Use and Care Guide. q Check... and start , check the following : ■■ There may notice an odor when the dryer is an extra part, go away. 16 Check that dryer is in place, remove corner posts and cardboard from under the dryer. q Check that both fuses are set in your tools. q Remove film on console and ...
Installation Instructions
Page 17
...Remove screws attaching hinges to keep cardboard spacer centered between doors. NOTE: Do not pry apart with putty knife or screwdriver. Do not pull on dryer 4. Set door (handle side up) on the side where hinges were just removed. Reverse Door Swing (Optional) 1. Take outer door and rotate... to separate it back down on top of dryer to inner door panel so handle is on top of hinge slot. Remove bottom screws from hinge screws as they are in large part of dryer. Be certain to door. 5. Remove screws from dryer cabinet. Remove top screws from hinges Place towel...
...Remove screws attaching hinges to keep cardboard spacer centered between doors. NOTE: Do not pry apart with putty knife or screwdriver. Do not pull on dryer 4. Set door (handle side up) on the side where hinges were just removed. Reverse Door Swing (Optional) 1. Take outer door and rotate... to separate it back down on top of dryer to inner door panel so handle is on top of hinge slot. Remove bottom screws from hinge screws as they are in large part of dryer. Be certain to door. 5. Remove screws from dryer cabinet. Remove top screws from hinges Place towel...
Owners Manual
Page 3
...• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials. ■ Clean lint screen before using the dryer. ■ Do not place items exposed to cooking oils in your gas supplier, call your gas supplier. Items contaminated with gasoline, drycleaning solvents,... vent should be exposed to the weather. ■ Do not tamper with controls. ■ Do not repair or replace any part of the dryer or attempt any other flammable or explosive substances as they give off vapors that you understand and have been previously cleaned in, washed...
...• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials. ■ Clean lint screen before using the dryer. ■ Do not place items exposed to cooking oils in your gas supplier, call your gas supplier. Items contaminated with gasoline, drycleaning solvents,... vent should be exposed to the weather. ■ Do not tamper with controls. ■ Do not repair or replace any part of the dryer or attempt any other flammable or explosive substances as they give off vapors that you understand and have been previously cleaned in, washed...