Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by susaarnd on March 14th, 2014
How Long Does It Take For Im115 To Ice Maker To Fill With Water
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... the supply line. • DO NOT install water supply tubing in a kit from electrical power before connecting a water supply line to the refrigerator. Coil enough tubing at the back of 1/4"
plastic is not recommended since it to malfunction. Chemicals from the softener may damage the ice maker, causing it greatly increases the potential for cleaning...
User Manual - Page 2
...Supply Tubing
4. Leveling Bracket Qty 1
8. Steel Clamp - Water Inlet Tube - Screws - Qty 1
7. Qty 2
10. Qty 2
5. Qty 1
9. Water Valve - Ice Maker
2. Leveling Bracket Screw - Qty 2
6. Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose ...
User Manual - Page 3
... cabinet (B).
8. Slowly lift up and pull on back of refrigerator. 1. Peel off label covering ice maker hole.
7. Remove freezer shelf (some models).
3. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from hole.
5. Push water inlet tube into small hole on shelf to left condenser mounting bracket screw(s). If...
User Manual - Page 4
... in one half turn with screw (6). Tighten screw (6) when level.
4 Adjust leveling bracket (7) to level ice maker (1). Push plastic water supply tubing (3) into freezer wall. Make sure water inlet tube (11) is sitting inside fill cup.
11. 9. Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later.)
13.
User Manual - Page 5
...ice container (2) on shelf.
18. Finger tighten nylon compression nut onto threaded end of rear panel. Tighten another one half turn with dynamic condensers, remount sound baffle, if installed. Locate factory punched holes at bottom right corner of water...cabinet liner. On refrigerators with wrench. Secure plastic water tubing to water valve. DO NOT over tighten.
16. Connect ...
User Manual - Page 6
... of 1/4 inch (6.4 mm) OD, copper tubing. Manufacturer will need to measure the distance from the ice maker inlet valve at shutoff valve and tighten any other surface.
8.
NOTE: Water line kit number 5303917950, available from your water supply line connections comply with all local plumbing codes. Reconnect refrigerator to electric power supply.
10.To turn...
User Manual - Page 7
... vacations. • If the ice maker will hit the ice when the ice container is full. Ice Maker Tips • Ice stored too long may develop an odd flavor. To stop the ice maker, lift the wire signal arm until the refrigerator is connected to water that water quality determines your dishwasher. • Wash ice container in warm water with mild detergent. Empty the...
Similar Questions
How Long Does It Take A Im115 Ice Maker To Make A Tray Of Ice
(Posted by trCA 10 years ago)
How Long For Frigidaire Ice Maker To Make A Cycle
(Posted by IonArashwan 10 years ago)
Why Does It Take 24 Hours For Im115 Ice Maker To Work?
(Posted by gsc724 11 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)