Hayward Max-Flo Support Question
Hayward Max-Flo Support Question
Find answers below for this question about Hayward Max-Flo.Need a Hayward Max-Flo manual? We have 2 online manuals for this item!
Question posted by ericbuckalew067 on January 11th, 2014
Where Does The Neutral Go Inside The Motor .
When you change the motor to 110 from 240 where does the neutral go in the motor there is no scamatic.
Current Answers
Answer #1: Posted by BusterDoogen on January 11th, 2014 2:30 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,397
Member since:
October 30th, 2011 Points: 28,565,397
Watch this video it will guide you through the wiring procedure.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Hayward Max-Flo Manual Pages
All Max-Flo II models - Page 1
... for both new construction or as a replacement pump. Designed for improved motor cooling and to operate in this manual carefully and completely. WARNING -
To prevent potential injury and to 122 degrees F, an elevated base for pools of all types and sizes, Max-Flo II features a Tri-Lock cam and ramp strainer cover with durable...
All Max-Flo II models - Page 2
Max-Flo II ™ Series ____
____
_____
_ Page 2 of the following : Failure to follow instructions may also be used with storable pools. When you see this symbol on your pump...Code (NEC). CAUTION -
It requires free circulation of the motor. If installed within an outer enclosure or beneath the skirt of a hot tub or spa, adequate ventilation and free circulation of air must be followed,...
All Max-Flo II models - Page 3
...entrapment. Installation of this manual. - Max-Flo II™ Series _____ _____
_____
...Also, contact a licensed electrician for information on the motor housing and to all
applicable local codes, regulations,...pool, spa, or hot tub.
Suction Entrapment Hazard. Suction in conformance with all electrical equipment, metal piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside...
All Max-Flo II models - Page 4
... to the pool. Failure to install according to seal with strainer cover lock ring.
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Do not change filter control ...pool and spa circulation system if a system component is also necessary to allow system water to return back to all system valves must be in violent separation of the Hayward Max-Flo IITM Series.
Motors...
All Max-Flo II models - Page 5
... flood when it is strongly advised to meet all local and national codes. Keep motor clean. Fasten pump to base or pad with screws or bolts to further reduce vibration...REPLACEMENT PARTS Suction line diameter must : Allow pump inlet height to pool as practical and run suction lines as direct as possible. Max-Flo II ™ Series__________
Product Specifications
_____
Page 5 of air for...
All Max-Flo II models - Page 6
... Plumber's Pipe Dope as it may cause damage. Fittings
Fittings restrict flow. Pool and spa fittings MUST conform to a gas supply line. Electrical
WARNING - Do NOT ground...to ground and bond pump motor can cause serious or fatal electrical shock hazard. Max-Flo II ™ Series __________ Pump Mounting (cont'd)
_____
Page 6 of a
swimming pool filtration system operate under pressure...
All Max-Flo II models - Page 7
... all metal parts within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub. Connect motor ground terminal to pool structure.
All electrical wiring MUST be maintained for no longer... Max-Flo II ™ Series _ _________
_____
Page 7 of 16
Electrical (cont'd.)
Voltage
Voltage at a water temperature no higher than 100° F (38° C). 5. Permanently ground motor. ...
All Max-Flo II models - Page 8
...damage plastic components in personal injury or death. Keep motor clean. Replace with compressed air. Strainer housing must be...flooding and voids the warranty. See "Shaft Seal Change Instructions" in your pool/spa system. Propylene glycol is removed. If no ... is higher than the pump, unscrew and remove strainer cover; Max-Flo II ™ Series
Page 8 of 16
Starting/Priming the ...
All Max-Flo II models - Page 9
Max-Flo...hold the motor assembly to protect delicate motor parts.
Rotate the impeller (item #10) counterclockwise and remove.
Inspect gaskets & replace if necessary. Shaft Seal Change Instructions
IMPORTANT...To avoid dangerous or fatal electrical shock hazard, turn OFF power to the pool. 2. To prevent motor shaft from mounting pad, wiring system (after power has been turned OFF...
All Max-Flo II models - Page 10
... (Be sure housing gasket (item#11) is in a clockwise direction. Press the spring seal assembly (item #12) onto the motor shaft - Re-attach assembly to 185 in step #4.
12. Tighten snugly by using torque pattern in diagram 1 at bottom of the...1
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Replace if damaged). Max-Flo II ™ Series
Page 10 of the ceramic seat.
All Max-Flo II models - Page 11
Max-Flo II ™ Series
Replacement Parts
Parts Diagram
Page 11 of 16
Item #16: Optional with some models
SEE PARTS LISTING ON NEXT PAGE
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
All Max-Flo II models - Page 12
..., Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V)
SPX2710Z2M Motor, 1-1/2 HP, Two Speed, Threaded Shaft
1
(Single Phase, 60 Cycle 115/230V)
SPX2715Z2M Motor, 2 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V)
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II ™ Series
Parts Listing
Page 12 of 16...
All Max-Flo II models - Page 13
.... Check voltage to Steps 4 & 5 of "Shaft Seal Change Instructions" in bubbles emanating from return fittings on motor data plate label. Check impeller for blocked suction line or dirty...Check For:
1. Max-Flo II ™ Series
Page 13 of overheating. Loose connections on valves. a. iii. Clogged or restricted strainer or suction line. Manually check rotation of motor shaft for line ...
All Max-Flo II models - Page 14
... seal assembly.
Motor bearings noisy from return fittings). backwash as per manufacturer's instructions; Solution: Re-tighten using Teflon tape. 5. Air leak in pool, and unrestricted discharge... clean or replace cartridge. 4. www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II ™ Series
Page 14 of filter, valve partially closed (high gauge reading)....
All Max-Flo II models - Page 15
... Division Street Elizabeth, NJ 07207
▲Retain this Warranty Certificate (upper portion) in materials and workmanship for cartage; Max-Flo II ™ Series
___
Page 15 of purchase. To original purchasers of this pump, Hayward Pool Products warrants its products free from defects in a safe and convenient location for a period of ONE (1) year...
All Max-Flo II models - Page 16
Max-Flo II ™ Series
___
Page 16 of 16
This Page is Blank
www.haywardpool.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
All Max-Flo models - Page 1
....
This cuts down on filter. (The air that the electrical supply available agrees with hot tubs and spas if so marked. Suction pipe should be readily disassembled for storable pools. Motors require free circulation of the motor. 4. Insure that is equipped with a 3 ft. (1 m) cord and twist lock plug, items 5 through pipe and fittings. STARTING...
All Max-Flo models - Page 3
...motor assembly to dislodge the diffuser. 15. Remove four bolts holding motor shaft with the diffuser in a dry, well-ventilated room.
SEAL CHANGE INSTRUCTIONS
SP2800X SERIES - For A.O.S. NOTE: Replace motor...rear center of the pump/strainer housing, exposing the diffuser. Keep motor clean. See instructions. MAX-FLO™
GENERAL
Exercise extreme care in the pump/strainer housing. ...
All Max-Flo models - Page 4
...;
Cavitation due to speed. 3. Vibration due to the factory without the expressed written authorization of Hayward Pool Products, Inc. No pumps or motors may be returned directly to improper mounting, etc. 4. MOTOR CUTS OUT-Check for : 1. The motor will automatically shut off suction as possible and determine if pump will auto-restart when safer...
Similar Questions
1 Hp Hayward Sp5500z2 Pool Pump Power Flo Matrix Motor Wont Start
(Posted by Rvesjeevi 10 years ago)
How To Remove Motor Mounting Plate From Motor?
Removed motor via 4 long housing cap screws with attached seal plate and motor mounting plate. Want ...
Removed motor via 4 long housing cap screws with attached seal plate and motor mounting plate. Want ...
(Posted by DNDEPAUL02 11 years ago)
How Many Watts Does The Max-flo Vs Use At Each Level
(Posted by dsevig 11 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)