Icom IC-M24 Support Question
Icom IC-M24 Support Question
Find answers below for this question about Icom IC-M24.Need a Icom IC-M24 manual? We have 1 online manual for this item!
Question posted by Anonymous-154138 on September 7th, 2015
Sound In Weather None In Chan 16
no sound in channel 16 no squelch or sound I follow instructions.........nothing
Current Answers
Answer #1: Posted by TommyKervz on October 16th, 2015 7:30 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Check if there is no water in the speaker grill.
Set the squelch level to the threshold level. page 10 of the manual.
Recharge the battery pack
You may also refer on the service manual for further assistance.
If the problem still remain unsolved please Email Technical Support Department or call them at (800) 253-1498 or (425) 450-6087.
Related Icom IC-M24 Manual Pages
Instruction Manual - Page 2
... care this radio should provide you for the IC-M24.
RWARNING!
This function works even when the radio is used, it may occur. The IC-M24 VHF MARINE TRANSCEIVER is subject to the condition that this Icom radio.
Personal injury, fire hazard or electric shock may occur. i
FEATURES
☞ Floats on the bottom of the radio, while floating...
Instruction Manual - Page 3
... the battery cover, antenna or DC Jack cap are detached from the transceiver.
"THIS IS name of the distress and assistance
required. 6. Your call on Channel 16.
❍ USING CHANNEL 16
DISTRESS CALL PROCEDURE
1. IN CASE OF EMERGENCY
If your position) 5.
Instruction Manual - Page 4
... provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from the body when transmitting and only use , always adhere to the following guidelines:
• DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may result in an uncontrolled environment...
Instruction Manual - Page 7
... BASIC OPERATION 8-13 ■ Channel selection 8 ■ Adjusting the volume level 10 ■ Adjusting the squelch level 10 ■ Receiving and transmitting 11 ■ Call channel programming 12 ■ Volume Loud...Scan types 14 ■ Setting TAG channels 15 ■ Starting a scan 15
6 DUALWATCH/TRI-WATCH 16 ■ Description 16 ■ Operation 16
7 SET MODE 17-20 ■ ...
Instruction Manual - Page 9
... marine channels 3, 21, 23, 61, 64, 81, 82 and
15
83, according to be. If required, only a
licensed radio operator may operate a transceiver.
5
However, non-licensed individuals may require a current radio station license before using the transceiver. However, even if you are prohibited under law.
tions.
12
13
NOTE: Even though the IC-M24 is...
Instruction Manual - Page 11
...
D Battery pack
To remove the battery pack: Slide the latch and then lift the battery cover to remove it .
12
13
14
15
Correct position
16
Incorrect position
Battery cover
Rubber seal Groove
Battery cover
3 Push the cover until the latch comes back to the rubber seal. If dust or other...
Instruction Manual - Page 12
... not be guaranteed. e PTT SWITCH [PTT] Hold down for 1 second to the normal operating mode. (p. 17) release to receive. (p. 11) r CHANNEL 16 KEY [16 9] ➥ Push to select Channel 16. (p. 8) ➥ Hold down for 3 seconds to enter the Call channel programming mode. (p. 12) ➥ While in the Set mode, push to return to select the Call...
Instruction Manual - Page 13
... or set 9
all TAG channels in the selected channel group. (p. 15)
o CHANNEL/WEATHER CHANNEL KEY [CH/WX U/I/C]
10
➥ Push to switch between a regular channel and a 11
weather channel. (p. 9) ➥ Hold down for 1 second to select the USA, International
12
and Canada channel groups. (p. 9)
13
➥ Push to return to the previous channel before selecting
Channel 16 or the Call...
Instruction Manual - Page 14
...16) "DW" appears during a scan.
"TW" appears during Triwatch.
!0 DUPLEX ICON Appears when a duplex channel is selected.
6
t CHARGE ICON (p. 23) Appears while charging. r CALL CHANNEL ICON (p. 8) Appears when the Call channel...a signal or when the squelch opens. (p. 11) ➥ Blinks while monitoring. (p. 13)
e TAG CHANNEL ICON (p. 15) Appears when a TAG channel is selected.
3 PANEL ...
Instruction Manual - Page 15
... the Weather Alert function is se- PANEL DESCRIPTION 3
!1 SUB CHANNEL READOUT ➥ Displays Channel 16 during a priority scan, Dualwatch or Tri-watch. (p. 16) ➥ Displays the Set mode item while in the Set mode. (p. 17) ➥ Displays the volume level while in the volume adjustment mode. (p. 10) ➥ Displays the squelch level while in the squelch adjustment...
Instruction Manual - Page 16
... for the first time, the battery pack must be programmed, and are used to store your most often used channel in the standby mode, you must monitor Channel 16. D Channel 16
Channel 16 is monitored during Tri-watch .
lecting Channel 16, or push [Y] or [Z] to the transceiver, turn OFF the power while charging.
Hold down [FAV], push [Y] or [Z] to...
Instruction Manual - Page 17
... 1 second to the next group. • USA, International and Canadian channel groups can automatically detect a weather alert 4
tone on the selected weather channel while receiving an- 5
other channel, or during a scan. (p. 18)
6
q Push [CH/WX] once or twice to select the Weather chan- 7
nel group.
• "WX" appears when a weather channel is selected.
8
• "WX ALT" appears when the...
Instruction Manual - Page 21
...8226; The backlight is automatically turned OFF after 5 seconds of the channel and function access. * Only in the Set mode. (p. 19)...13 The monitor key action can be selected in the volume or squelch adjustment mode, and volume loud
and Volume Mute functions. ➥ ...activated.
14
15
16
Hold down both [SCAN] and [Hi/Lo].
11
• A low vibration tone sounds for night-time operation...
Instruction Manual - Page 22
...
CH 05
CH 04
* Previously selected weather channel. (when the Weather Alert function is activated)
A normal scan, like a priority scan, sequentially searches through all TAG channels. However, unlike a priority scan, Channel 16 is not checked unless Channel 16 is set as those for standby convenience. when a signal is detected on a channel other than Channel 16, the scan switches to quickly...
Instruction Manual - Page 23
... is in use, select a desired
6
weather channel using [CH/WX] and [Y] or [Z]. (p. 9)
7
w Push [SCAN] to start a priority or normal scan. • "SCAN" blinks while scanning.
8
• "16" appears on the sub channel readout during a priority scan.
9
• When a signal is received
Push
Blinks
Appears
Blinks
15 Scanning starts
16
When a signal is received, the scan...
Instruction Manual - Page 24
... disappears.
• To transmit on the selected channel during Tri-watch. • A beep tone sounds when a signal is received on Channel 16. • Tri-watch on INT channel 07.
e Hold down [PTT].
■ Operation
q Select Dualwatch or Tri-watch
• If a signal is received on Channel 16, Dualwatch/Triwatch pauses on Channel 16 until the signal disappears.
• If...
Instruction Manual - Page 25
... Push [Y] or [Z] to change the settings of the item.
7
t To exit the Set mode, push [16].
8
SET MODE ITEMS (The display shows the current settings, and the selected item is used to select a... desired option of transceiver's
D Set mode operation
2
functions: Beep Tone function, Weather Alert function, Prior- q Turn OFF the power.
3
ity Scan function, Scan resume timer, ...
Instruction Manual - Page 26
... ALT" icon blinks and a beep sounds. The currently selected weather channel is checked while the
Power Save function is activated, or during a scan.
• "ALT" appears when the function is detected, the scan pauses on the channel
for 5 seconds, and then resumes.
A normal scan searches all TAG channels while monitoring Channel 16. When the func-
fore any...
Instruction Manual - Page 27
... scan ON
D Dual/Tri-watch function
"dt"
Set the watch type to Dualwatch or Tri-watch. (p. 16)
Dualwatch function (default)
Push
Tri-watch function
D Monitor key action
"Sq" 1
The monitor key temporarily opens the squelch. The squelch stays open until any key is activated by holding down [MONI] (VOL/SQL) for 30 seconds.
Instruction Manual - Page 29
... Lithium-ion batteries may result in the following hazards: smoke, fire, or ... any
7
purpose that comes into contact with Icom radios or Icom chargers. If fluid from inside...;C; -4˚F to +140˚F) and the
16
battery itself is specified. Immediately wash...emits an abnor- High temperature buildup in this instruction manual.
8
R DANGER!
Misuse can result....
Similar Questions
How Can I Open The Ic 7200 For Transmission On Marine Channels?
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
(Posted by Runeedamm 5 months ago)
How Do I Change The Itu Region On This Radio? I Cannot Transmit In The 432 Range
Was testing a digital packet modem with the 9100 and realized I cannot transmit in the 432 Mhz area....
Was testing a digital packet modem with the 9100 and realized I cannot transmit in the 432 Mhz area....
(Posted by n1gmv 9 months ago)
Ic7410 Monitor Inaudible
The monitor on my IC7410 does not seem to work on SSB. I get plenty of sidetone on CW, but cannot he...
The monitor on my IC7410 does not seem to work on SSB. I get plenty of sidetone on CW, but cannot he...
(Posted by michaelagburch 11 months ago)
